ZALMAN N5 MF ATX MID Tower Computer Case

Precautions

• Read this manual carefully before installing.
•  Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
•  Wear gloves to prevent accidents when installing the product.
•  Severe damage may occur when mounting the system, so do not apply excessive force.
•  Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
•  Be careful not to block the ventilation hole of the product when using the system.
•  Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
• Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
•  Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
•  Store and use the product out of children’s reach.
• Our company assumes no responsibility for any problem that occurs due to theuse of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
• The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.

Specifications

Fan Support

| Top| 3 x 120mm
Front| 3 x 120mm
Rear| 1 x 120mm
Bottom| 2 x 120mm

Fan(s) Inclued

| Front| 3 x 120mm (with RGB LED Effect)
Rear| 1 x 120mm (with RGB LED Effect)

Radiator Support

| Front| 120mm / 240mm / 360mm
Rear| 120mm

I/O Ports

| 1 x Headphone, 1 x Mic, 2 x USB 2.0, 1 x USB 3.0, Reset Button, Power Button, Fan-LED Controller (Change Fan Speed & LED Brightness)

Accessories

• User’s Manual

• Buzzer

• SSD / MB Screws x 20

• Cable Ties x 5

• PSU / HDD / VGA Screws x 8

• Thumm Screws x 2

• Motherboard Standoffs x 3

I/O Ports

| Part| #| Part| #| Part| #| Part

---|---|---|---|---|---|---|---
ⓐ| Power Button| ⓑ| USB 2.0 Ports| ⓒ| HDD / Power LED| ⓓ| Headphone Jack
ⓔ| Microphone Jack| ⓕ| Fan Controller| ⓖ| USB 3.0 Port| ⓗ| Reset Button

1. Removing the side panels

   • Acrylic Panel
   • Steel Panel
     

2. Removing the front panel

3.  Mounting the motherboard

   •  Motherboard size
     Pick out the 8-Pin auxiliary power cable(CPU power connector) through the groove on top before installing motherboard.

   • ATX

   • mATX

   • Mini-ITX
     

4. Mounting the PSU
   

5. Mounting the PCI-E(VGA) card
   

6. Mounting the 3.5″ and 2.5″ SSD / HDD
   

7. Mounting the 2.5″ SSD / HDD
   

8. Mounting the fans

   • Mounting the top fans
   • Mounting the bottom fans

9. Fan(s) Inclued

   • Front : 3 x 120mm Fan – with RGB LED Effects
   • Rear : 1 x 120mm Fan – with RGB LED Effects

10. Fan Controller
    4 Control Modes of Fan speed & LED brightness Mode| Fan Speed| LED Brightness
    ---|---|---
    Mode 1.| High| High
    Mode 2.| Low| Low
    Mode 3.| Low| Off
    Mode 4.| Off| Off

Caution: shutting off your system fans could cause increase of system temperature.

11.  I/O Connectors

References

• zalman.com
• ANDPRO.RU - интернет магазин компьютерной и офисной техники с выгодными ценами и доставкой

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>