SONY 5-051-921-11 2 Way Speaker Instructions

June 15, 2024
Sony

SONY 5-051-921-11 2 Way Speaker Instructions

Dimensions

XS-160GS

XS-130GS

A Reference Point
B Reference Plane
C Reference Axis

Precautions

  • Do not continuously use the speaker system beyond the peak power handling capacity.
  • Keep recorded tapes, watches, and personal credit cards using magnetic coding away from the speaker system to protect them from damage caused by the magnets in the speakers.
  • Please note the following when installing the units; otherwise malfunction and/or deterioration in sound quality may result.
    • Do not touch the diaphragms and/or speaker cones by hand or with tools.
    • Do not put your fingers through the holes of the frame.
    • Do not drop foreign objects in the units.
  • Do not place this product close to medical devices.
    • This product (including accessories) has magnet(s) which may interfere with pacemakers, programmable shunt valves for hydrocephalus treatment, or other medical devices. Do not place this product close to persons who use such medical devices. Consult your doctor before using this product if you use any such medical device.

If you cannot find an appropriate mounting location, consult your car dealer or your nearest Sony dealer before mounting.

Specifications

XS-160GS

  • Speaker: Coaxial 2 way: Woofer 16.5 cm (6 1 /2 in) cone type Tweeter 2.0 cm (13/16 in) dome type
  • *Short-term maximum power1:* 250 W2
  • Rated power: 40 W*2
  • CTA 2031 RMS Power: 45 W
  • Rated impedance: 4 Ω
  • Output sound pressure level: 89 dB ± 2 dB (1 W, 1 m)*2
  • Effective frequency range: 45 Hz – 24 000 Hz*2
  • Mass: Woofer: Approx. 650 g (1 lb 7 oz) per speaker
  • Supplied accessories: Parts for installation

XS-130GS

  • Speaker: Coaxial 2 way: Woofer 13 cm (5 1 /4 in) cone type Tweeter 2.0 cm (13/16 in) dome  type
  • *Short-term maximum power1:* 230 W2
  • Rated power: 30 W*2
  • CTA 2031 RMS Power: 35 W
  • Rated impedance: 4 Ω
  • Output sound pressure level: 89 dB ± 2 dB (1 W, 1 m)*2
  • Effective frequency range: 50 Hz – 24 000 Hz*2
  • Mass: Woofer: Approx. 550 g (1 lb 3 oz) per speaker
  • Supplied accessories: Parts for installation

Design and specifications are subject to change without notice.

  1. “Short-term maximum power” may also be referred to as “Peak Power”.
  2. Testing Condition: IEC 60268-5 (2003-05)

Mounting

Before mounting

A depth of at least 46.3 mm (1 7 /8 in) for XS-160GS or 45.3 mm (1 13/16 in) for XS-130GS is required for flush mounting. Measure the depth of the area where you are to mount the speaker, and ensure that the speaker is not obstructing any other components of the car. Keep the followings in mind when choosing a mounting location:

  • Make sure that nothing is obstructing around the mounting location of the door (front or rear) or the rear tray where you are to mount the speaker.

  • A hole for mounting may already be cut out of the inner panel of the door (front or rear) or the rear tray. In this case, you need to modify the board only.

  • If you are to mount this speaker system in the door (front or rear), make sure that the speaker terminals, frame or magnet do not interfere with any inner parts, such as the window mechanism in the door (when you open or close the window), etc.
    Also make sure that the speaker grille does not touch any inner fittings, such as the window cranks, door handles, arm rests, door pockets, lamps or seats etc.

  • If you are to mount this speaker system in the rear tray, make sure that the speaker terminals, frame or magnet do not touch any inner parts of the car, such as the torsion bar springs (when you open or close the trunk lid), etc.
    Also make sure that the speaker grille does not touch any inner fittings, such as seat belts, head rests, center brake lights, inner covers of the rear wipers, curtains or air purifiers, etc.

Parts list

Parts list

  • Mounting from the car interior
  • DOOR (FRONT/REAR)

(XS-160GS/XS-130GS)

  1. Mark the 4 bolt holes and make them 3.2 mm (5/32 in) in diameter

  2. Speaker cord (not supplied)

Power amplifier, etc
Note
When releasing the cables, push down on the catch firmly and release them carefully. If excessive force is used, damage to the speaker or cable terminals may result

  1. XS-160GS

    XS-130GS

Flat mounting (installed flush with the surface of the dash)

XS-130GS

This speaker can be made to fit in almost any type of car by removing the mounting tabs.
Use clippers or pliers, etc. to cut or snap two of the mounting tabs off so that it is even with the edge of the speaker frame as illustrated.

Note
After removing the mounting tabs, handle the speaker frame with care, as the edges may be sharp.

Notice for customers: the following information is only applicable to equipment sold in countries applying EU directives
This product has been manufactured by or on behalf of Sony Corporation.

EU Importer: Sony Europe B.V.
Inquiries to the EU Importer or related to product compliance in Europe should be sent to the manufacturer’s authorized representative, Sony Belgium, bijkantoor van Sony Europe B.V., Da Vincilaan 7-D1, 1930 Zaventem, Belgium.

Disposal of old electrical & electronic equipment (applicable in the European Union and other countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring that this product is disposed of correctly, you will help to prevent potential negative consequences for the environment and human health, which could be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Notice for customers: the following information is only applicable to equipment sold in UK applying relevant statutory requirements
This product has been manufactured by or on behalf of Sony Corporation.

UK Importer: Sony Europe B.V.
Inquiries to the UK Importer or related to product compliance in the UK should be sent to the manufacturer’s authorized representative, Sony Europe B.V., The Heights, Brooklands, Weybridge, Surrey KT13 0XW, United Kingdom.

Disposal of old electrical & electronic equipment (applicable in the European Union and other countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring that this product is disposed of correctly, you will help to prevent potential negative consequences for the environment and human health, which could be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals