ZALMAN X7 ATX Full Tower Computer Case User Manual
- June 3, 2024
- ZALMAN
Table of Contents
- Precautions
- Specification
- Accessories Component
- Case construction
- I/O Port
- | Part| #| Part| #| Part
- Separating the side panel
- Mounting the main board
- Mounting PSU
- Mounting PCI-E(VGA) card
- Mounting the riser card
- Mounting 5.25” device
- Mounting 2.5” SSD and HDD
- Mounting the 3.5” and 2.5” HDD
- Cable Connection
- Separating the top panel
- Mounting the top fan and radiator
- Separating the front panel
- Separating the front bezel
- Mounting the fan and radiator in the front
- Mounting the custom water cooler
- Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZALMAN X7 ATX Full Tower Computer Case User Manual
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
- Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Specification
Model | X7 |
---|---|
Case Form Factor | ATX FULL TOWER |
Dimensions | 617 x 230 x 587(H)mm |
Weight | 17.5kg |
Case Materials | Aluminum, Steel, Plastic |
Motherboard Support | E-ATX / ATX / M-ATX / M-ITX |
Maximum GPU Length | 420mm |
Maximum CPU Cooler Height | 175mm |
Maximum PSU Length | 180mm |
PCI Expansion Slots | 8 + 2 |
Case Drive Bays | 1 x 5.25”, 6 x 3.5”. 5 x 2.5” |
Fan Mount Locations | Front |
Top | 3 x 120mm / 2 x 140mm |
Rear | 1 x 120mm / 1 x 140mm |
Fans Included | Front |
Rear | 1 x 120mm(with RGB LED effect) |
Radiator Mount Locations | Front |
Top | 240mm / 280mm / 360mm |
Rear | 120mm / 140mm |
I/O Ports | 1 x Headphone, 1 x Mic, 4 x USB 3.0 |
RGB Fan Controller
| Channels| 8 + 2
Connectors| Fan: 8 x 6-Pin
LED Strip: 2 x 4-Pin
Power: 1 x 4-Molex Pin
RGB Fan Controller
Accessories Component
Case construction
A ·················· Tempered glass| G ·· Tool-free 2.5″, 3.5″ combo
HDD cage| M ··················· Side I/O port
---|---|---
B ············· Aluminum front panel| **H ·············· ·2.5″
SSD, HDD cage| N ············ Radiator & Fan bracket
C ···················· Front bezel| ** I ·············· Aluminum
top panel| O ····················· VGA guide
D ····················· Dust filter| **J ·········· ZM-MFC5(RGB
fan controller)| P ··················· Rubber cover
E ····················· Vent filter| ****K ················ Front
RGB display| Q ············· VGA mounting guide
F ·········· ZM-F3 STR(120mm RGB fan)| ****L ······················
Top bezel| R** ················ Side RGB display
I/O Port
| Part| #| Part| #| Part
---|---|---|---|---|---
**A| Headphone| ****B| Mic| ****C| USB 3.0
****D| HDD LED| ****E| Power button| ****F**| Reset button
Separating the side panel
Loosen the side hand screw and separate the tempered glass panel.
Mounting the main board
As 6 stand-offs are mounted by default, insert an additional standoff according to the type of main board by referring to the mounting position of the main board, and mount the main board on the case.
Mounting PSU
Fix the PSU on the PSU mounting hole located at the bottom of the case using the screw.
Mounting PCI-E(VGA) card
Loosen the screw, separate the PCI cover, mount the graphic card, and fix it using the screw.
Mounting the riser card
Fix the riser card on the riser card-mounting hole using the screw, and mount the graphic card on the relevant position.
Mounting 5.25” device
Insert the 5.25” device into the side 5.25” bay until it is latched. (For a product where the fan controller is mounted, installation is possible only after separating the product and the fan. Separate the panel at the top, loosen the screw from the bottom of the fan controller, and separate it.)
Mounting 2.5” SSD and HDD
Separate the 2.5” SSD and HDD cage on the side of the case by pushing it to the right and assemble the 2.5” SSD or HDD. Mount the assembled SSD on the cage-mounting hole by pushing it to the left.
Mounting the 3.5” and 2.5” HDD
Separate the tool-free 2.5” and 3.5” combo HDD cage and assemble the HDD or SSD. Mount the assembled HDD on the slot.
Cable Connection
Separating the top panel
Loosen the screw at the back and separate the top panel.
Mounting the top fan and radiator
Separate the radiator and fan bracket by loosening the fixed hand screw and assemble the radiator or the fan. Fix the assembled radiator and fan bracket on the top bracket-mounting hole using the hand screw.
Separating the front panel
Hold the groove at the bottom front and separate the panel.
Separating the front bezel
Separate the bezel by pulling it in the direction of the arrow as shown in the figure.
Mounting the fan and radiator in the front
Mount the fan or the radiator on the mount hole in the front as shown in the figure.
Mounting the custom water cooler
You can clamp the water bottle to the custom water cooler mounting hole as shown in the figure.
Warranty
Zalman Tech products come with the following limited warranties:
1 Year Warranty
CPU coolers (All CNPS series, Reserator 3 Max series), computer cases,
keyboards, mice, laptop coolers, case fans, hardware enclosures (including VE
series), audio devices, and all other accessorei s not specified below.
3 Year Warranty
GVM Series Power Supply Units
7 Year Warranty
ARX,EBT series Power Supply Units
Zalman USA has the right to change availability of limited warranty at its own
discretion and any changes will not be retroactive.
The limited warranty does not cover…
- Non-Zalman brand products and accessories.
- Problems resulted from external causes such as accident, abuse, misuse, and/or problems with electrical power.
- Any service not authorized by Zalman USA.
- Usage that is not in accordance with product instructions.
- Failure to follow the product instructions and/or failure to perform preventive maintenance.
- Problems caused by using accessories, parts, and/or components not supplied by Zalman.
- Products with missing, altered Service Tags and/or seria lnumbers.
For United States and Canada
Technical support and warranty related inquiries:
support.usa@zalmanusa.com
Toll free customer service:
1-888-925-6266
For all other regions
Send e-mail to techsupport@zalman.co.kr
For detailed warranty information, please visit
www.zalman.com.
References
- ZALMAN.COM
- ANDPRO.RU - интернет магазин компьютерной и офисной техники с выгодными ценами и доставкой
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>