ZALMAN Z7NEO ATX Mid Tower User Manual

User’s Manual
TEMPERED GLASS & RGB LED LIGHTING SYNC
Ver. 051019

Z7NEO ATX Mid Tower

• To ensure safe and easy installation, please read the following precaution.
• Product design and specifications may be revised to improve quality and performance without notice.

Developed and designed by ZALMAN in Korea.
This product is protected by ZALMAN’s pending or registered patents.

www.zalman.com

Z7 NEO

Precautions

• Read this manual carefully before installing.
• Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
• Wear gloves to prevent accidents when installing the product.
• Severe damage may occur when mounting the system, so do not apply excessive force.
• Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
• Be careful not to block the ventilation hole of the product when using the system.
• Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
• Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
• Do not insert your hand or another object into the product during operation, as this may injure your hand or damage the object.
• Store and use the product out of children’s reach.
• Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
• The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.

Specifications

LED Control Button, Reset Button, Power Button

Caution (Radiator Support)
※ Limited fitment to memory equipped with heatsinks.
※ Some motherboards with tall heat sink will cause interference on the installation of the 280mm radiator.

Accessories

I/O Ports

• LED Control Button

1. Short Press : 1st ~ 10th RGB LED Lighting Mode (Effects & Colors)11th RGB LED Lighting Mode Off
2. Long Press : RGB LED Lighting Mode Change (LED Control Button Motherboard Sync)

Removing the side panels

1. Tempered Glass
   

2. Steel Panel

Mounting the motherboard

2-1. Motherboard size

Mounting the PSU

4. Mounting the PCI-E(VGA) card

5. Mounting the 3.5″ and 2.5″ SSD / HDD

6. Mounting the 2.5” SSD / HDD

7. Mounting the top fans

8. Mounting the front radiator

Caution
※ Limited fitment to memory equipped with heatsinks.
※ Some motherboards with tall heat sink will cause interference on the installation of the 280mm radiator.

Fan specifications

I/O Connectors

RGB LED Controller

Fan 1~8 / 6Pin
– Connector to RGB LED fans (Four pre-installed)
– RGB LED Fans I/O port 8ea B LED Control Button / 2Pin
– Connector to LED control button
– RGB LED Lighting effects & 7 Colors C DC Power / 4Pin
– Connector to PSU
– Input: 12V D Motherboard Sync / 4Pin
– Connector to the motherboard
– Requires a motherboard that supports RGB sync ※ Caution
Please be sure to check the arrow of the female cable, it indicates where 12V needs to be connected when you are connecting it to the motherboard.

Certification

1. RGB LED Controller

RGB LED Controller
**

1. : ZM-RGB8P-4AS
   2) KC EMC : R-R-ZMT-ZM-RGB8P-4AS
   MEMO
   www.zalman.com
   **  site: https://andpro.ru
   : +7 495-545-4870
   email: info@andpro.ru

References

• zalman.com
• ANDPRO.RU - интернет магазин компьютерной и офисной техники с выгодными ценами и доставкой

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>