ZALMAN Z8, Z8 MG, Z8 TG ATX MID Tower Computer Case User Manual
- October 27, 2023
- ZALMAN
Table of Contents
Z8, Z8 MG, Z8 TG ATX MID Tower Computer Case
User Manual
Ver. 041120
- To ensure safe and easy installation, please read the following precaution.
- Product design and specifications may be revised to improve quality and performance without notice.
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
- Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Specifications
| Model | Z8 I | Z8 MS | I Z8 TG | |
|---|---|---|---|---|
| Case Form Factor | ATX Mid-Tower | |||
| Dimensions | 460 x 212 x 493(H)mm | |||
| Weight | 6.3kg | I 6.8kg | ||
| Case Materials | Tempered Glass, Plastic, Steel | |||
| Motherboard Support | E-ATX(-280mm) / ATX / mATX / Mini-ID( | |||
| Maximum VGA Length | 350mm | |||
| Maximum CPU Cooler Height | 160mm | |||
| Maximum PSU Length | 180mm | |||
| PCI Expansion Slots | 7 | |||
| Drive Bays | 2 x Combo (3.5″ or 2.5″, Toolless ), 4 x 2.5″ | |||
| Fan Support | Top | 2 x 120mm / 2 x 140mm | ||
| Front | 3 x 120mm / 3 x 140mm | |||
| Rear | 1 x 120mm | |||
| Bottom | 2 x 120mm (Remove SSD Brackets) | |||
| Fan(s) Included | Front | 3 x 120mm | Addressable RGB 3 x 120mm | |
| Rear | 1 x 120mm | |||
| ARGB Controller Included | ||||
| Radiator Support | Top | 120mm / 240mm / 280mm | ||
| Front | 120mm | |||
| Rear | 120mm | |||
| I/0 Ports | 2 x USB3.0, 1 xUSB2.0, 1 x Headphone Jack, |
1 x Microphone jack, Power Button, Reset Button, LED Button
Accessories
I/O Ports
| Part
---|---
ⓐ| Power Button
ⓑ| HDD / Power LED
ⓒ| Headphone Jack
ⓓ| Microphone Jack
ⓔ| USB 2.0 Port
ⓕ| USB 3.0 Ports
ⓖ| Reset Button
ⓗ| LED Button
Removing the side panels
| 2. Removing the front panel | 3. Mounting the motherboard |
|---|
3-1. Motherboard size
4. Mounting the PCI-E(VGA) Card
5. Mounting the 2.5” SSD
6. Mounting the 3.5″ HDD
Mounting the PSU
8. Mounting the radiator
Fans Included / Specifications
Z8
Front (120mm Fan)
RPM : 1,100 ±15%
Input : 12V ** 0.16A
Sleeve Bearing
4-Pin| Z8 MS, Z8 TG
Front (ARGB 120mm Fan)
RPM : 1,300 ±15%
Input : (Fan)12V ** 0.16A
(LED)5V **** 0.5A
Hydro Bearing
4-Pin
---|---
10. Mounting the fans
- Mounting the top & bottom fans
・2 x 120mm
・2 x 140mm| 2) Mounting the front fans
・3 x 120mm
・3 x 140mm| 3) Mounting the rear fan
・1 x 120mm
---|---|---
11. I/O Connectors
Developed and designed by ZALMAN in Korea.
This product is protected by ZALMAN’s pending or registered patents.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>