Webasto BlueCool F-Series Fresh Air Instruction Manual
- June 5, 2024
- Webasto
Table of Contents
Webasto BlueCool F-Series Fresh Air
About this document
This document is an integral part of the product and contains the information required to ensure correct and safe installation and operation. The Operating Instructions (OI) are an integral part of the product and provide the information required to ensure correct and safe operation.
Using this document
- Read these Operating Instructions (OI) carefully before operating the unit.
- Please pass this document on to the next owner or user of the unit.
Use of symbols and highlighting
This document uses warning labels and colors for hazard classification in
accordance with ISO 3864: See also https://www.iso.org/standard/55814.html.
DANGER
This signal word denotes a hazard with a high degree of risk which, if not
avoided, will lead to death or seri-ous injury.
WARNING
This signal word denotes a hazard with a moderate de-gree of risk which, if
not avoided, may lead to minor or moderate injury.
CAUTION
This signal word denotes a hazard with a low degree of risk which, if not
avoided, will lead to minor or moder-ate injury.
NOTE
This signal word denotes a Special Technical Feature or (if not observed)
potential damage to the product. Refers to separate documents which are
enclosed or can be requested from Webasto.
Warranty and liability
Webasto shall not assume liability for defects or damage that are the
result of the Installation Instructions / Operating Instructions and the
instructions contained therein being disregarded. This liability exclusion
particularly applies to:
- Installation by untrained personnel.
- Improper use.
- Repairs not carried out by a Webasto service workshop.
- Use of non-genuine parts.
- Conversion of the unit without permission from Webasto.
Webasto Service App
The type label of the F series (see Type Label) contains a QR code that can
be used to call up further additional technical documentation in various
languages. For this purpose, please use the Webasto Service App, which is
available as a download for iOS ( Apple) and Android (Google).
Safety
Intended use
The Bluetooth F-Series is used for fresh air supply on boats and ships.The
BlueCool F-Series has been built according to the current state of technology
and recognized safety rules.
WARNING
Improper or inappropriate use may result in danger to life and limb of the
user and others, as well as impairment of the unit and other property. Any
other use of this product is not permissible. Any other use of or changes to
the product, including as part of assembly and installation, will result in
any and all warranty claims being voided.
WARNING
Risk of injury, damage to the product. The BlueCool F-Series must only be
operated in their fi-nal installed position.
WARNING
Ignition of surrounding gases or highly flammable liquids by sparking of the
BlueCool F-Series. You must always switch off the air conditioning system when
refueling, or while in a petrol station area.
NOTE
This device may be used by children from the age of eight if they are
supervised or have been instructed re-garding the safe use of the device and
understand the resulting dangers.
Operation
The Bluetooth MyTouch control element for the BlueCool F-Series enables you to control the connected system. The display doubles up as a touch screen. Instructions are included in this document.
ATTENTION
The display must not come in contact with any other electrical devices. The
electrostatic discharge could cause malfunctions. Do not use pointed or sharp
objects to operate the screen. Do not exert excessive pressure.
NOTE
Webasto recommends operating the screen using your fingers only. The touch
sensitivity of the screen is op-timized to fingertip contact. The screen may
not re-spond if gloves are worn.
Tapping at the very edge of the screen may not be recognized.
Home screen and icons
- On/off
- Notification
- Settings
- Crew menu
Standby
The screen will go to Standby mode after 5 minutes if the screen remains
untouched. Tap anywhere on the screen to bring up the Home screen.
Notification
The notification icon appears on the bottom status line to draw your
attention to the current status of the system. Tap the icon to show the
current status.
ON/OFF
When the screen is off:
- Tap the screen
- The screen switches on.
When the screen is on:
- Tap the green/grey field
- The color of the ON/OFF symbol indicates the operating status of the BlueCool (green = switched on).
Operation
After switching on in automatic mode F3, the control starts the Fresh air
unit and the connected Extract air unit one after the other and then switches
to start mode. In the first 30 sec. both fans of fresh air and extract air
unit op-erate with nominal air flow rate and detect the current temper-ature
conditions of the outdoor air. During this phase, the proportional valve is
partially opened to accurately sense the actual chilled water temperature. If
the outside air temperature is lower than the cabin supply air set point
temperature, the unit will begin reheating the outside air even regardless of
the chiller’s current operating mode. If the outside air temperature is higher
than the set target temperat-ure, the unit will begin to cool, but only if the
available chilled water temperature is lower than the outside air
temperature.It is recommended to operate the fresh air system in F3 auto-matic
mode. In that mode the system is able to adapt to differ-ent weather
conditions. If the chiller is operated in F1 “Cooling only” mode, the electric
heating of the fresh air unit is still activ-ated. If the supply air
temperature is higher (cooling) or lower (heat-ing) than the set temperature,
the message
- High supply air temperature
- Low supply air temperature
- Undercooling protection
is displayed.The fan will not operate if “Shutdown high supply air temperat- ure” or “Shutdown low supply air temperature” is activated. This prevents air that is too warm or too cold being blown into the cabin.The fan will operate if “Shutdown high supply air temperature” or “Shutdown low supply air temperature” is deactivated. This ensures a sufficient supply of fresh air, when needed. However the supply air temperature will be warmer or colder than the set value.The fan will NOT operate if the supply air temperature is below 12 °C in order to prevent cabins getting too cold.In cooling mode, the cold water temperature is significantly be-low 15 °C and in heating mode significantly above 40 °C. For changes to these shutdown parameters, please contact your authorised Webasto Marine dealer or service partner.
System settings
- Tap the Settings icon.
- Setting level 1 is displayed.
- Tap to scroll between pages.
Settings menu
You can access the settings menu by tapping the Settings icon from the home
screen. The settings menu is displayed. The available functions are:
Brightness
Adapts the screen brightness to the ambient light levels.
Language
Sets the operating language.
Standby
Sets the BlueCool MyTouch display to Standby mode. In Standby mode, the
available functions are:
- Website Logo
- Shows the Webasto logo.
- Customer logo
- Shows an individual file in .BMP (bitmap) format, that you can load onto the BlueCool MyTouch using the BlueCool Expert tool.
- Cabin temperature – bright
- Shows the current cabin supply air temperature at high brightness levels in areas with bright ambient light.
- Cabin temperature – dim
- Shows the current cabin supply air temperature at low brightness levels in areas with little ambient light.
- Display off
- No display in Standby mode.
- Operating indicator
- An illuminated dot indicates that the system is ready for operation.
- Standby off
- The Home screen remains active.
Maintenance
- Check the sea-water and chilled water circuit for leaks in the entire system and from the sea-cock to the sea-water outlet.
- Check the condensate line for unobstructed drainage of the condensate water tray.
- Check air-ducting for damage, interruption and free flow.
- Check proper functioning of the system by running it for at least 10 minutes.
- Check electrical connections for corrosion of contacts and firm fitting.
Status / Error message table
Screen | LED “Alive” | Possible cause | Possible cause |
---|---|---|---|
AAA Under- voltage | 1x flashing, pause… | Switch-off as a result of under- |
voltage. The power supply is below the set undervoltage value for longer than 5 seconds. This may be caused by an excessively long cable, over- loading or an insufficiently high power-generator output.| Provide a more suitable power supply.
If this does not solve the problem, please contact your au- thorised Webasto Marine dealer or service partner.
A09
Cabin supply air temperature sensor
| 2x flashing, pause…| l Cabin supply air temperature sensor defective
l Break/ short-circuit in electrical circuit
l Temperature sensor not connec- ted
| Please contact your authorised Webasto Marine dealer or service partner.
A10
Cold water temperature sensor
| 3x flashing, pause…| l Cold water temperature sensor defective
l Break/ short-circuit in electrical circuit
l Temperature sensor not connec- ted
| Please contact your authorised Webasto Marine dealer or service partner.
A60
Internal air temperature sensor
| 4x flashing, pause…| l Internal air temperature sensor defective
l Break/ short-circuit in electrical circuit
l temperature sensor not connec- ted
| Please contact your authorised Webasto Marine dealer or service partner.
A61
Air flow rate
| 6x flashing, pause…| l Air flow interrupted
l Air flow paths or filters blocked
l Fan inactive
| Please contact your authorised Webasto Marine dealer or service partner.
A62
High air tem- perature sup- ply
| 7x flashing, pause…| l Outdoor temperature too high
l Cooling capacity insufficient
| Switch on the refrigeration system, check cooling mode, check flow, bleed
water circuit, deactivate ECO mode for V series, switch off air handler in
unused cabins. Check the electric heater’s power supply.
A63
Low air tem- perature sup- ply
| 8x flashing, pause…| l Outdoor temperature too low
l Heating capacity insufficient
| Switch on the refrigeration system, check heating mode, check diesel heater,
check flow, bleed water circuit, deactiv- ate ECO mode for V series, switch
off air handler in unused cabins. Check the electric heater’s power supply.
A64
Undercooling protection
| 9x flashing, pause…| l Outdoor temperature too low
l Heating capacity insufficient
| Switch on the refrigeration system, check heating mode, check diesel heater,
check flow, bleed water circuit, deactiv- ate ECO mode for V series, switch
off air handler in unused cabins. Check the electric heater’s power supply.
A65
Filter service
| 23x flashing, pause…| Filter replacement interval expired| Please contact
your authorised Webasto Marine dealer or service partner.
Init
Data commu- nication
| 5x flashing, pause…| l Initialization procedure or sys- tem blocked
l Electrical wiring defective
l Interruption in power circuit/ short circuit
| Please contact your authorised Webasto Marine dealer or service partner.
References
- rbasto1 (Ricardo Basto) · GitHub
- Webasto - Home
- Inspirational facades, seamless acoustic surfaces and floor coatings by Sto
- ISO - ISO 3864-3:2012 - Graphical symbols — Safety colours and safety signs — Part 3: Design principles for graphical symbols for use in safety signs
- Webasto Group - Feel the Drive
- ISO - ISO 3864-3:2012 - Graphical symbols — Safety colours and safety signs — Part 3: Design principles for graphical symbols for use in safety signs