Webasto W9030026A SmartControl Control Panel User Guide
- June 5, 2024
- Webasto
Table of Contents
- Control Element and menu
- Buttons and control
- Back-function
- Symbols
- Switching on and off by quick start button
- Switching on and off through the menu
- Timer
- Important Information on Operating and Installation Instructions
- Intended use
- Statutory regulations governing installation
- Installation
- Electrical Connections
- Dimensions
- Declaration of Conformity
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Webasto W9030026A SmartControl Control Panel User Guide
Control Element and menu
- Submenu name
- Submenu symbol
- Activated time settings
- Time
- Quick start button
- Control knob
*: if installed
Buttons and control
Button | Control and function |
---|---|
Quick start button (5) with status display. | |
Control knob (turn/push button) (6) for selection and confirmation of the |
selected functions.
Back-function
Exit the selected menu with the “Back” function.
The settings are saved and the higher-level menu level is displayed.
Symbols
Symbol | Description | Symbol | Description |
---|---|---|---|
Timer menu (programme time setting) | Ventilation menu | ||
Heating-Normal | Settings menu | ||
Heating level Normal | Heating level Eco | ||
Heating level Boost | Fan speed (level 1-4) | ||
Add timer | Activate timer | ||
Deactivate timer | Delete timer | ||
Delete all timers | Active timer | ||
Quick start | Day of the week | ||
Time | Language | ||
Temperature unit | Day/Night | ||
System information | Error message | ||
Reset | Service indicator (service required) | ||
To the left | Attention | ||
**** | Back | **** | To the right |
--- | --- | --- | --- |
**** | 12 hour format | **** | Symbol for confirmation |
**** | Operating voltage too low | **** | ADR display |
**** | Altitude correction |
At temperatures below –20 °C protective function of control element display is
active.
Display and background illumination are switched off, heating status is
indicated by status of LED diode. The heater can be tuned on and off by quick
start button without any limits.
Switching on and off by quick start button
“Quick start” function enables heating or ventilation by simply pressing the button. Operation time, temperature and heating mode can be preset in the settings in menu item “Setting the quick start”.
Press quick start button (5).
Heating or ventilation starts functioning.
The quick start button (5) lights up when the heater is in operation:
- Green (Heating)
- Blue (Ventilation)
By pressing quick start button (5) heating or ventilation can be ended prematurely at any moment.
Switching on and off through the menu
Switching on the heating through the menu
Heating menu has been selected in the main menu.
Press the control knob (6).
The heating level, required temperature and/or operation time must be set in accordance with the installed heater. Follow the instructions displayed in the menu.
You can select the setting by turning the control knob. You confirm selection
by pressing the control knob.
The heating starts functioning as soon as all the settings have been chosen.
By pressing quick start button (4) heating can be ended prematurely at any
moment.
Setting ventilation through the main menu (optional)
Ventilation menu has been selected in the main menu.
Press the control knob (6).
The fan speed, required temperature and/or operation time must be set in accordance with the installed heater. Follow the instructions displayed in the menu.
You can select the setting by turning the control knob. You confirm selection
by pressing the control knob.
The ventilation starts functioning as soon as all the settings have been
chosen.
By pressing quick start button (5) during functioning, ventilation can be
ended prematurely at any moment.
Timer
The function is not available in ARD operation (hazardous substance transportation).
Timer menu has been selected in the main menu.
Press the control knob (6).
”Add timer” message (if no timer has been saved yet) appears in the display.
Press the control knob in order to add new timer.
In order to programme the timer you should enter the desired day of the week and switch-on and switch-off time. Follow the instructions displayed in the menu.
As soon as settings are entered, the programmed timer is saved and shown in the display.
**** Press the control knob in order to activate the programmed timer.
“Activate” message appears in the display.
**** Press the control knob in order to confirm activation.
All programmed times can be deactivated, edited or removed. If the “Timer” symbol has been selected in the main menu, all saved timers appear in the display in chronological order. The following functions are at the disposal after selecting the desired timer: “activate”, “deactivate”, “edit” and “delete”.
Important Information on Operating and Installation Instructions
DANGER
-
Do not operate the heater in closed rooms due to the danger of poisoning and suffocation.
-
Always switch off the heater before refuelling.
-
The improper operation, installation or repair of Webasto heaters and control elements can cause fire or the leakage of deadly carbon monoxide. This can lead to serious injury or death.
-
Webasto shall not assume liability for defects or damage that are the result that the installation and operating instructions as well as the instructions contained therein being disregarded.
This liability exclusion particularly applies for:- installation by untrained personnel
- improper use
- repairs not carried out by a Webasto service workshop
- use of non-genuine parts
- Conversion of the heater without permission from Webasto
-
If faulty always replace the complete control element.
Intended use
The control element MultiControl | SmartControl is used to operate the Webasto
water or air heaters for cabin and engine preheating.
The control element MultiControl | SmartControl is currently approved for
connection to certain Webasto water or air heaters.
Statutory regulations governing installation
Regulations/Type-approval numbers for MultiControl | SmartControl
Electromagnetic compatibility
ECE R10 04 7319 MultiControl | SmartControl
NOTE
The provisions of these regulations are binding within the scope of EU
Regulation 2018/858 and should also be observed in countries where there are
no special regulations
IMPORTANT
Failure to follow the installation instructions will result in the
invalidation of the type approval for the heater and therefore invalidation of
the general homologation of the vehicle.
NOTE
For vehicles with an EU type approval, an entry is not required in accordance
with § 19 section 4 of appendix VIII b of StVZO. Country-specific registration
regulations must be complied with.
Installation
Detailed information can be found in the operating and installation
instructions.
The documents are stored on the DVD included in delivery.
- Install and connect wiring harness, see Section „12 Electrical
- Connections“. X Connect and install MultiControl | SmartControl.
Electrical Connections
DANGER
Incorrect handling
Cables damaged on sharp edges can cause short-circuits. Fit protectors on
sharp edges.
Connector designation
Con. | Description | Remarks |
---|---|---|
1 | W Bus / Low Switch / Diagnostics | The connection is configured differently |
depending on the heater selected. Please note that there is no W-bus on this
line for heaters with analogue control. W-bus diagnostics are only possible
with a W-bus heater connected or with a UniBox connected.
2| SAU1 switch output| max. switching current 500 mA
3| KL30| Plus+
4| KL31| Earth-
Dimensions
Declaration of Conformity
CE-Declaration of Conformity and UKCA-Declaration of Conformity
The MultiControl | SmartControl was developed, manufactured, tested and
supplied in accordance with the relevant directives, regulations and standards
for safety, EMC and environmental compatibility.
Webasto declares that the product MultiControl | SmartControl is manufactured
and delivered in accordance with the directives and regulations. The complete
CE Declaration of Conformity and UKCA Declaration of Conformity can be found
in the download area at https://dealers.webasto.com.
In multilingual versions the German language is binding. If a language is not available, please contact the Webasto Service Centre for this purpose (see the brochure with the service phone numbers of the respective subsidiaries).
Europe, Asia Pacific
Webasto Thermo & Comfort SE
Postfach 1410
82199 Gilching
Germany
Company address:
Friedrichshafener Str. 9
82205 Gilching
Germany
UK only :
Webasto Thermo & Comfort UK Ltd
Webasto House
White Rose Way
Doncaster Carr
South Yorkshire
DN4 5JH
United Kingdom
You will find more detailed operating instructions at www.webasto.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>