Norauto 2274031 Booster with 8000mAh Lithium Battery Instruction Manual
- June 5, 2024
- Norauto
Table of Contents
Norauto 2274031 Booster with 8000mAh Lithium Battery Instruction Manual
FOREWORD
We thank you for choosing our product. It is designed for you according to the highest quality standards. Please read the operation manual carefully before using and operating the unit. Heed all warnings. If the device is passed on to another person, this manual must be handed over to the user along with it. Please keep this manual handy for future reference.
INTENDED USE
SAFETY WARNINGS
-
BEFORE CHARGING , READ THE INSTRUCTIONS.
-
FOR INDOOR USE. DO NOT EXPOSE TO RAIN.
-
DISCONNECT THE SUPPLY BEFORE MAKING OR BREAKING THE CONNECTIONS TO THE BATTERY.
-
WARNING : EXPLOSIVEGASES.
PREVENT FLAMES AND SPARKS .
PROVIDE ADEQUATE VENTILATION DURING CHARGING. -
Use this appliance only as described in this instruction manual. Any misuse of the appliance, or use different from what is explained in the manual, will not engage the liability of the manufacturer nor of the reseller.
-
Do not attempt to modify the appliance in any way. Modifications might lead to damage of the appliance, property damage or personal injury for which the manufacturer will accept no liability.
-
Vehicles may have electrical and electronic systems ( e . g . e n g i n e management systems, mobile phones) that maybe damaged if subjected to high starting voltages and voltage peaks.
Before connecting the appliance to the vehicle, read the vehicle’s owner’s manual to confirm that external charging is allowed. -
The disrespect of the safety instructions can cause electric shock, fire and/or injuries to persons.
-
Follow instructions for connecting and disconnecting the battery charger leads or battery terminals.
-
This appliance is meant for domestic and indoor use only.
-
Do not use any accessory not recommended by the manufacturer/reseller! They may damage the appliance and/or cause injuries to persons.
-
CHOCKING HAZARD! Keep the appliance and its packaging elements out of reach of children.
-
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision. -
Children should be supervised to ensure that they do not play with the appliance.
-
Do not operate the appliance in explosive atmospheres, such as in presence of flammable liquids, gases or dust.
-
Avoid naked flames, hot surfaces and sparks area during the use of this appliance. Do not smoke when using the appliance.
-
During charging, the battery must be placed in a well-ventilated area.
-
Keep the appliance dry. Do not immerse it into water nor into any other liquid.
-
Keep the appliance away from water and spatters.
-
Do not operate the appliance in a humid environment. Do not use in wet places.
-
No object containing liquid should be kept around this appliance.
-
Do not cover the appliance with objects like paper, towels, curtains, etc.
-
Do not expose the appliance directly to the sun, nor to hot temperatures.
-
Do not let the supply cord hang from a table edge, do not let it touch any hot surface.
-
When you unplug the appliance, always pull on the plug itself, never pull on the supply cord.
-
If the supply cord or the clamps are damaged, do not use the appliance.
-
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
-
Do not modify the supply cord nor the plug. If the cord and/or the plug do not match your electrical installations, contact a qualified technician.
-
An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and electric shock.
-
Do not let the red and black clamps touch each other, as it may lead to sparks, explosion and cause damages.
-
Before making any electrical connection, check that:
-
The appliance and its components are not damaged. In which case, do not use the appliance but bring it back to your reseller for inspection and fixing.
-
The indicated voltage on the rating label matches with your electrical installations.
-
Position the battery charger as far away from the battery as the leads will allow.
-
Explosive gases may collect near the ground. Locate the battery charger as high as possible above ground level.
-
Do not proceed to any maintenance operation by yourself. Any check, disassembling or fixing has to be performed exclusively by a qualified person.
-
Do not open body casing. There are no user-serviceable parts inside.
-
Do not place the battery charger above or stand the battery charger on top of the battery.
-
The battery terminal not connected to the chassis has to be connected first.
The other connection is to be made to the chassis, remote from the battery and fuel line. The battery charger is then to be connected to the supply mains. After charging, disconnect the battery charger from the supply mains. Then remove the chassis connection and then the battery connection.
SAFETY INSTRUCTIONS REGARDING BATTERIES
-
WARNING: Risk of explosive gas mixtures.
Working in the vicinity of a lead-acid battery is dangerous. Batteries generate explosive gases during normal battery operation. For this reason, it is of utmost importance that each time, before using your battery charger, you read this manual and follow the instructions exactly. -
Thanks to check that your batteries can be recharged with this charger. To know this, refer to the manufacturer’s instruction manual of the battery.
-
Make sure that the initial charging rate does not exceed the battery manufacturer’s requirement.
-
Do not put batteries in use during the charge! Do not start the engine during the charge.
-
Non-rechargeable batteries must not be recharged.
-
Never attempt to charge a frozen battery!
-
Wear complete eye protection and suitable clothing to give protection from contact with battery fluid. Avoid touching the eyes while working with a battery.
Acid, acid particles or corrosion may get into the eyes. -
Remove personal metal items such as rings, bracelets, necklaces and watches when working with a lead-acid battery.
Be extra cautious to reduce the risk of dropping a metal object onto the battery.
This might cause sparks or short-circuit the battery or other electrical parts, and lead to an explosion or severe burn. -
In wrong circumstances, some fluid can be ejected from the battery. Battery fluid can cause irritations and/or burns.
Avoid any contact with it. In case of accidental contact, immediately rinse the spot with water. If fluid enters your eye, immediately rinse the eye with plenty of fresh water and contact a doctor. -
Worn-out batteries must be safely scrapped. Read the “Disposal of this product” chapter in this manual to learn more about recycling and environment protection.
-
Respect the technical specifications of the batteries that you want to charge, along with the corresponding specific recommendations (for example: how to insert and connect the battery, charge rate, etc.).
-
Do not recharge dry-cell batteries commonly used in household appliances.
It may cause a fire and damage to persons. -
This appliance must be used exclusively on automotive vehicle batteries with 12Vdc voltage. Do not connect the appliance to other types of systems (6Vdc, 24Vdc, etc.).
-
The appliance is only to be used with the power supply unit provided with the appliance DC05.
-
WARNING: For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance: car charger DC05.
-
This appliance contains batteries that are only replaceable by skilled persons.
-
This appliance contains batteries that are non-replaceable.
PACKAGING
SN | ACCESSORIES | QTY |
---|---|---|
1 | Car charger | 1 |
2 | USB cable | 1 |
3 | Smart Clamps | 1 |
4 | USB car charger | 1 |
5 | Accessory bag | 1 |
6 | Manual | 1 |
PART LIST
-
Engine start port
-
Work light
-
USB output
-
USB charging input port
-
On/Off (POWER)
-
LEDs
-
Smart clamps
-
USB car charger
-
USB cable
OPERATION
NOTES:
- Dual USB 5V DC power output interface, the highest current is 2.4A.
- Work lights: highlight, steady, slow flash, flash, SOS and other five working modes.
- With travel lock function, it is convenient to shut down during travel to avoid accidentally switch on the device.
- 5 LEDs indicates the level of internal battery status.
- Product protection functions: reverse polarity protection, over current protection, short circuit protection, over charge protection, reverse charge protection, over discharge protection, over temperature protection, fire protection.
CHARGING
CAUTIONS:
- Charge the unit before using for the first time.
- When the battery level is 2 LEDs, the device should be charged ASAP. If with only 1 LED, it should be charged immediately
CHARGING THE JUMP STARTER
- Car charger: Connect the car charger to cigarette lighter, and connect the USB cable to the car charger and input port (4) of jump starter.
- USB charging: Use an external USB to connect to the product’s USB input port (4) for charging
CHARGING INDICATION
- Charging: LED flashes each one to solid green until all blue;
- Full charged: all blue LEDs will be solid blue.
NOTE: After charging is completed, and the charger is not disconnected, the charging mode will be automatically restored if the battery voltage drops to 12V.
NOTE: It is recommended to recharge the Jump Starter every 3-4 months to maintain the efficiency and prolong the service life of the internal battery even if the unit has not been used.
JUMP START
WARNING: When using this unit to start, make sure the positive and negative connections are correct, otherwise the battery may explode.
Follow the steps below for jump start, otherwise it will be dangerous:
- Insert “Smart Clamps” into the engine start port of the device first.
- Connect the red (+) clamp with the positive (+) side of the battery.
- Connect the black (-) clamp with the metal part of the engine (negative ground) or to the negative battery.
- After the connection is completed, follow the instructions in Table 1 below to check whether the connection is correct and proceed to the next step.
- Start the car and do not cranking over 5 seconds.
- If the engine does not start successfully, check battery level and if the battery is over 3 bars, wait 3 minutes to try again.
- After the engine is successfully started, first pull the “smart clamps” off the device and then remove the clamps from the car battery.
- Charge the unit immediately after each use.
SMART CLAMPS
SN| GREEN LED| RED LED| AUDIBLE WARNING|
STATUS
---|---|---|---|---
1| Flash| Flash| Off| No car battery connected.
2| On| Off| Off| Connected to the standby state.
3| Off| On| On| Short circuit alarm.
4| Off| On| On| Reverse polarity alarm.
5| Off| On| On| Reverse charging voltage protection.
6| Off| On| On| Internal temperature exceeds 75 °C, over temperature alarm.
7| Off| On| Off| Time-out alarm (connection status exceeds 30s).
USB OUTPUT
- Connect the USB cable to the USB output port of the device (3), 5V DC, 2.4A or 9V DC, 2A, please refer to the technical data.
- Short press the “POWER” button (5), USB provides 5V 2.4A output to provide charging for mobile phones/tablets and other electronic products.
- The USB output will be automatically turned off after charging is completed.
- When the load current exceeds 2.4A, the USB output will be automatically turned off.
- The charging time will be more than 8 hours, and the USB output will be automatically turned off.
WORK LIGHT
- Press and hold the “POWER” button (5) over 3 seconds to turn it on.
- Lighting (2) working mode:
- Turning ON: 100% brightness
- 1st short press: 50% dim light
- 2nd short press: Slow flash
- 3rd short press: Flash
- 4th short press: SOS
- 5th short press: Close
- After continuing to work for more than 5 seconds in any working mode, short press the “POWER” button (5) will turn off the light directly.
TRAVEL LOCK
- Press and hold the “POWER” button (5) over 8 seconds to turn on the travel lock mode.
- In this mode, the device will fall into sleep (lock state): short press the “POWER” button (5) would not turn on the USB output, work light output or 12V output.
- To turn off the “travel lock” mode: Press and hold the “POWER” button (5) again for over 8 seconds to release the device.
CLEANING AND MAINTENANCE
- WARNING: Always disconnect the device from the power supply before cleaning or maintenance.
- Never immerse the unit in water or other liquids.
- Do not use abrasive cleaning agents or hard objects during cleaning as these can damage the product.
- Store the appliance in a cool, dry place, protected from moisture and direct sunlight.
TROUBLESHOOTING
QUESTION | ANSWER |
---|---|
Why didn’t my Jump starter start my vehicle? | There could be a number of |
reasons why the Jump starter did not start your vehicle. Check the following:
- Ensure the Jump starter battery is fully charged.
- Ensure the vehicle operates on 12V DC.
- Ensure the displacement of the car.
- The vehicle’s battery may be below 2.5V, the minimum start voltage for the Jump starter. Ensure all connections are correct, then press the Power/ Light and Jump-start buttons simultaneously for 3 seconds to manually activate the Jump starter. (This is optional and various according to product.)
Can I leave my Jump starter connected to the car after it has started?|
Leaving the Jump starter connected to the car after it has started will not be
a problem. But it is best to disconnect and charge the Jump starter so it is
ready to start another car. As the Jump starter will not be receiving charge
in this situation and it is best to pack the Jump starter away so it will not
fall in the engine area.
What is Peak Amps?| Peak amps is the maximum current the battery in the Jump
starter can produce.
What is Cranking Amps?| Cranking Amps is the continuous current available
during jump starting.
How do I turn off the product?| The product has intelligent detection
function. If there is no load, or the electronic product is charged for long
time, the device will automatically fall into “sleep” and save the energy.
NOTE: The engine start port on the device is always live and is protected with rubber cover.
How long do I have to charge the product?| Time to full charge varies:
- USB 5V 2A: 4 – 6 hours
- USB 5V 1A: 8 – 12 hours
- USB 5V 0.5A: 16 – 24 hours.
How many times can I charge my cell phone?| Take the iPhone XS as an example.
The mobile phone can be fully charged 2 times from no power shut-down to full
charge. Other brands of mobile phones can charge more than 1-3 times according
to the capacity of the mobile phone.
How many starts per full charge?| Depends on the displacements, the number of
starts could be very different. For example, if it’s 1.2L car, it could have
20+ starts.
What’s the service life?| It could be used for 1-5 years on non-commercial
uses.
How long do I have to charge the jump starter?| The jump starter is very well
built. It is no problem to store for 6-12 months, but in order to prolong the
service life, it is recommended to charge once every three months.
What’s the use of travel lock function?| This is Greatway’s patent. It is
characterized by turn off deeply, that preventing abnormal power consumption,
USB output and 12V output short circuit caused by improperly stored
miscellaneous items during travel.
What are the protection features of this product?| There are 8 protections:
- Reverse polarity protection: prevent the harms from clamps being reversed;
- Over-current protection: prevent damage to the product caused by excessive input charging current;
- Short circuit protection: prevent the clamps from being shorted between positive and negative poles;
- Overcharge protection: when fully charged, or external input voltage is too high, the device won’t accept charge;
- Reverse-charge protection: stop the reverse charging from car after jump starting;
- Over-discharge protection: keep the device from discharging when battery is too low. This keeps a weak device from cranking;
- Over-temperature protection: Automatically stop working when the temperature is getting too high for during charging, lighting, and USB interface use;
- Spark protection: prevents sparks when the clamps are connecting car batteries.
TECHNICAL DATA
Battery | Lithium Ion 8000 mAh (29.97 Wh) |
---|---|
Cranking Amps | 200 A |
Peak Amps | 400 A |
Input | USB 5 V , 2.1 A Max |
Output | 12 V (engine start) |
USB 5 V , 2.4 A; 9 V , 2 A
Temperature range| -10 °C ~ +55 °C
Storage temperature| -20 °C ~ +60 °C
Dimension| 146 x 78 x 27.3 mm
Weight| 0.33 kg
This product meets all the basic EU regulatory requirements relevant to it.
Selective collection of waste electrical and electronic equipment.
Electrical equipment must not be disposed of with household waste.
Pursuant to European Directive 2012/19/EU on waste electrical and electronic
equipment, and its transposition into national law, waste electrical equipment
must be collected separately and disposed of in designated collection points.
Contact the local authorities or the vendor for advice on recycling.
This symbol means that the product contains batteries covered by European Directive 2013/56/EU. Disposing of batteries with household waste is prohibited. Contact the public collection points in your local municipality for proper disposal.
WARNING: To reduce the risk of injury, the user must read the instruction manual.
NORAUTO
511/589 rue des Seringats 59262 Sainghin-en-Mélantois France
Distribué par / Distributed by / Vertrieben von:
Norauto France 511/589 rue des Seringats 59262 Sainghin-en-Mélantois
Auto 5 Bld Paepsem 20 -1070 ANDERLECHT BELGIQUE
A.T.U Auto-Teile-Unger Handels GmbH & Co.KG,
Dr.-Kilian-Str. 11, D-92637 Weiden i.d.OPf Deutschland
Noroto España SAU Centre Comercial Alban Carretera de Ademuz
km 2,9 46100 BURJASSOT
Norauto Italia SPA Corso Savona 85/10024 MONCALIERI
Norauto Portugal LDA Av. dos Cavaleiros, n°49 Alfragide 2794-057 CARNAXIDE
www.norauto.com
www.atu.eu
Made in P.R.C / Fabricado en/na R.P.C / Fabriqué en R.P.C