SuperMax Tools 19-38 Drum Sander Owner’s Manual
- July 26, 2024
- SuperMax Tools
Table of Contents
- 19-38 Drum Sander
- Specifications:
- Product Usage Instructions:
- 1. Unpacking and Setup:
- 2. Safety Precautions:
- 3. Operating the Drum Sander:
- 4. Maintenance:
- Q: How do I select the correct abrasive for my drum
- Q: What should I do if I encounter issues with my SuperMax
- …….PART NO…………..DESCRIPTION…………………………………………….. SIZE …………………………………………..QTY
- 8X1/2″………………………………………………. 2 34….. 480DS-134 ……….. LOCK WASHER
- …….PART NO…………..DESCRIPTION…………………………………………….. SIZE …………………………………………..QTY
- …….PART NO…………..DESCRIPTION…………………………………………….. SIZE …………………………………………..QTY
- 6-32X1/2″…………………………………………. 2 19….. 480BS-219 ……….. SWITCH ON/OFF
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
19-38 Drum Sander
“`html
Specifications:
- Model: 19-38 Drum Sander
- Brand: SuperMax Tools
- Power: 110V, 60Hz
- Weight: 200 lbs
- Dimensions: 24″ x 36″ x 24″
Product Usage Instructions:
1. Unpacking and Setup:
Before using the drum sander, ensure you have read the manual
thoroughly. Unpack the machine carefully and place it on a stable,
level surface. Check for any visible damage before proceeding.
2. Safety Precautions:
Always prioritize safety when operating the drum sander. Wear
eye protection at all times and avoid loose clothing that could get
caught in the machine. Ensure the dust cover is closed, and the
dust collector is connected before operation.
3. Operating the Drum Sander:
a. Turn on the power and adjust the feed rate according to the
type of material being sanded.
b. Feed the boards against the drum rotation to prevent
kickback.
c. Maintain control of the boards throughout the sanding
process.
4. Maintenance:
Regular maintenance is essential for optimal performance. Clean
the machine after each use, check for wear on abrasive belts, and
ensure all locks are tightened before operation.
FAQ:
Q: How do I select the correct abrasive for my drum
sander?
A: Refer to the abrasive selection guide in the manual (page 12)
for recommendations based on the type of material you are
sanding.
Q: What should I do if I encounter issues with my SuperMax
Tools drum sander?
A: Refer to the troubleshooting section in the manual (page 20)
for common issues and solutions. If problems persist, contact your
SuperMax Tools distributor for assistance.
“`
OWNER’S
MANUAL
19-38
DRUM SANDER
© 03/2017 SuperMax Tools Pat. 9,132,521
®
C
US
269049
P. 888.454.3401
SuperMaxTools.com
F. 651.454.3465 sales@SuperMaxTools.com
CONGRATULATIONS
SuperMax Tools takes pride in our products and stands behind them with
continuing service and support for our customers. Your SuperMax Tools sander
was designed with several features that will bring a new dimension of
productivity to your shop. Our goal at SuperMax Tools is to develop machines
that provide you with maximum performance, maximum economy and maximum
utility. Your 19-38 drum sander has features that will give you better results
in less time in the years ahead. This sander is designed to be tailored to
every project and features ultra-precise control for any sanding project.
This sander is covered with a warranty and your distributor can answer any
questions you may have. Additionally, we will always be here to offer support,
service information, and product supplies and services. Before using your
sander for the first time learn how to use it. This manual covers unpacking
step-by-step, sander set up and fine-tuning the controls. Safety information
is also provided to makes sure your process is hassle free. If you have any
questions this manual will provide answers and you can also refer to our
website or customer service for any updates or further details.
MODEL IDENTIFICATION
Your 19-38 drum sander is one of a family of machines from SuperMax Tools
designed to help you achieve re-
sults comparable to industrial-size sanders at a fraction of the cost. For
future reference, find the model, stock and serial numbers on the back of
machine base and write them in below.
Model:
Date Purchased:
Stock Number:
Distributor:
Serial Number:
IMPORTANT: KEEP THIS MANUAL HANDY
Please read this manual first. It was designed to help you get the most from
your 19-38 drum sander. Before unpacking or using the machine, familiarize
yourself with its components, features, and basic adjustments by reviewing the
following pages. You will find it an invaluable aid in setting up, operating
and servicing your machine. If, after reviewing this manual, you still have a
problem you can’t solve, please call your SuperMax Tools distributor.
WARNING: SAFETY FIRST
When maintaining and operating this machine, always put safety first. For your
own safety, read and understand this owner’s manual before operating this
machine. Always heed and follow all normal safety precautions, including the
following:
a. Always wear eye protection while operating sander. b. Always feed boards
against the drum rotation. c. Tighten all locks before operating. d. Keep
hands and clothing away from operating drum. e. Do not operate sander with
dust cover opened. f. Do not operate sander without dust collector connected
to the dust cover. g. Always maintain control of boards to avoid kickback
(know how to prevent it). h. Always disconnect power before servicing or
adjusting.
WARNING: FOR YOUR OWN SAFETY READ THIS INSTRUCTION MANUAL BEFORE OPERATING THE SANDER.
TABLE OF CONTENTS
safety rules ………………………………………………………………………………………….4 grounding instructions
…………………………………………………………………………5
specifications………………………………………………………………………………………..6
warranty………………………………………………………………………………………………6 about the superMax tools druM
sander…………………………………………………7 unpacking your druM
sander………………………………………………………………….7 setting up your superMax tools druM sander
………………………………………11
Checking drum alignment………………………………………………………………………………………………………………………………11
Connecting Dust Collectors……………………………………………………………………………………………………………………………12
Power and Electrical Safety ……………………………………………………………………………………………………………………………12
abrasive selection guide ………………………………………………………………………12
Wrapping Abrasives……………………………………………………………………………………………………………………………………….13
Proper Abrasive Wrap Position ………………………………………………………………………………………………………………………14
Abrasive Wrap Tension Adjustment ……………………………………………………………………………………………………………….14
Maximizing Abrasive Longevity ……………………………………………………………………………………………………………………..14
operating your druM sander ………………………………………………………………..15
Drum Depth of Cut …………………………………………………………………………………………………………………………………………15
Conveyor and Speed Rate………………………………………………………………………………………………………………………………16
Stock Feeding Operation………………………………………………………………………………………………………………………………..16
Stock Feeding Maximum Performance………………………………………………………………………………………………………….16
Tension Roller Pressure………………………………………………………………………………………………………………………………….17
Tension Roller Contact
Adjustment………………………………………………………………………………………………………………..17 Conveyor Belt
Tension……………………………………………………………………………………………………………………………………18 Conveyor Belt
Tracking…………………………………………………………………………………………………………………………………..18
Maintenance ………………………………………………………………………………………..18
Monthly Maintenance…………………………………………………………………………………………………………………………………….18
Replacing Conveyor Belts ………………………………………………………………………………………………………………………………18
Cleaning the Machine…………………………………………………………………………………………………………………………………….19
supply checklist ………………………………………………………………………………….19 troubleshooting your
superMax tools druM sander…………………………….20 wiring diagraM
…………………………………………………………………………………….22 parts list and
diagraMs…………………………………………………………………. 23-27
SAFETY RULES
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from tool before turning it on.
3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet
locations, or expose them to rain. Keep work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work
area.
6. MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing
starter keys.
7. DON’T FORCE TOOL. It will do the job better and safer at the rate for
which it was designed.
8. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it
was not designed.
9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good
condition. When using an extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized cord will cause a drop
in line voltage resulting in loss of power and overheating. Table A (on the
next page) shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller
the gage number, the heavier the cord.
10. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get caught in moving parts. Nonslip
footwear is recommended. Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting
operation is dusty. Everyday eyeglasses only have impact resistant lenses,
they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer
than using your hand and it frees both hands to operate tool.
13. DON’T OVERREACH. Keep proper footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing; when changing accessories, such as
blades, bits, cutters, and the like.
16. REDUCE THE RISK OF UNINTENTIONAL STATING. Make sure switch is in off
position before plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended
accessories. The use of improper accessories may cause risk of injury to
persons.
18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or
if the cutting tool is unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that it will
operate properly and perform its intended function – check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction
of rotation of the blade or cutter only.
21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool
until it comes to a complete stop.
Some dust created by power sanding, sawing, grinding, drilling and other
construction activities contain chemicals known to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are: · Lead from
lead based paint. · Crystalline silica from bricks, cement, and other masonry
products. · Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals, work in a well-ventilated area and
work with approved safety equipment, such as face or dust masks that are
specifically designed to filter out microscopic particles.
4
TABLE A – MINIMUM GAUGE FOR CORD
AMPERAGE RATING
–
MORE THAN
0 6 10 12
–
NOT MORE THAN
6 10 12 16
VOLTS
120 240
–
TOTAL LENGTH OF CORD (IN FEET)
25
50
100
150
50
100
200
300
MINIMUM GAUGE FOR CORD
18
16
16
14
18
16
14
12
16
16
14
12
14
12
Not recommended
GROUNDING INSTRUCTIONS
1. All grounded, cord-connected tools:
In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This
tool is equipped with an electric cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged into a matching outlet that is
properly installed and grounded in accordance with all local codes and
ordinances.
· Do not modify the plug provided – if it will not fit the outlet, have the
proper outlet installed by a qualified electrician.
· Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. The conductor with insulation having an outer surface
that is green with or without yellow stripes is the equipment-grounding
conductor. If repair or replacement of the electric cord or plug is necessary,
DO NOT CONNECT the equipment-grounding conductor to a live terminal.
· Check with a qualified electrician or service personnel if the grounding
instructions are not completely understood, or if in doubt as to whether the
tool is properly grounded.
· Use only 3-wire extension cords that have 3-prong grounding plugs and 3 pole
receptacles that accept the tool’s plug.
· Repair or replace damaged or worn cord immediately.
2. Grounded, cord-connected tools intended for use on a supply circuit having
a nominal rating less than 150 V:
· This tool is intended for use on a circuit that has an outlet that looks
like the one illustrated in sketch A in Fig. 1. The tool has a grounding plug
that looks like the plug illustrated in sketch A in Fig. 1. A temporary
adapter, which looks like the adapter illustrated in sketch B and C, may be
used to connect this plug to a 2 pole receptacle as shown in sketch B if a
properly grounded outlet is not available. The temporary adapter should be
used only until a properly grounded outlet can be installed by a qualified
electrician. This adapter is not permitted in Canada. The green-colored rigid
ear, lug, and the like, extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box.
3. Grounded, cord-connected tools intended for use on a supply circuit having
a nominal rating between 150 250 V, inclusive:
· This tool is intended for use on a circuit that has an outlet that looks
like the one illustrated in sketch D. The tool has a grounding plug that looks
like the plug illustrated in sketch D. Make sure the tool is connected to an
outlet having the same configuration as the plug. No adapter is available or
should
5
be used with this tool. If the tool must be reconnected for use on a different
type of electric circuit, the reconnection should be made by qualified service
personnel; and after reconnection, the tool should comply with all local codes
and ordinances.
Fig. 1: Grounding Methods
SPECIFICATIONS
Maximum Width Minimum Length Maximum Thickness Minimum Thickness Dimensions Drum diameter Dust port diameter Height Adjustment Conveyor Motor Drive Motor (TEFC) Power Requirements Shipping Weight (3 boxes)
38″ (2 passes) 2-1/4″ 4″ 1/32″ 36″ x 42″ x 24″ (without stand) 5″ diameter – 1740 rpm. 4″ 1/16″ per revolution (depth scale included) Direct drive D.C. motor; Infinitely variable 0 – 10 ft/min 1-3/4 HP – Continuous-duty 110 V, 1 Ph, 20 A 286 lbs (weight varies on how equipped)
2 YEAR WARRANTY
Limited warranty. We will provide all replacement parts which are found to be
defective in materials or workmanship. Manufacturers’ warranties on conveyor
belts. Register the warranty for your new machine by filling out and mailing
in the warranty registration card supplied in the package with each new
machine.
NOTE: You can also register online using our fast and easy warranty form by
visiting our website at www.SuperMaxTools.com
6
ABOUT THE SUPERMAX TOOLS DRUM SANDER
This manual is designed to help familiarize you with your SuperMax Tools drum
sander, and to help you take advantage of its exclusive features. By
understanding its major components, and how they work together, you will be
able to get the most from your investment.
The SuperMax Tools drum sander is basically made up of:
1. Height adjustment handle of the drum. 2. Shroud. 3. Depth scale. 4. Knob to start feed conveyor and selects feed rate.
5. Starts and stops the motors. 6. Conveyor table. 7. Tension roller contact adjustment. 8. Drum carriage.
1 2
3
8
4
7
5
6
UNPACKING YOUR SUPERMAX TOOLS DRUM SANDER
Your 19-38 drum sander has been shipped mostly assembled from the factory. If
any damage has occurred as a result of shipment, notify the transportation
company as soon as possible and ask them to make an immediate inspection. Ask
for a damage or loss report. Also notify your distributor of any loss or
damage during shipment. See enclosed Warranty Statement. NOTE: Before setting
up make sure that the space is adequate for your new equipment. We also
recommend that there is more than one person available for lifting and initial
set up procedures.
TO AVOID PROBLEMS AND POTENTIAL DAMAGE TO THE MACHINE, PLEASE READ THROUGH THE
UNPACKING INSTRUCTIONS BELOW BEFORE PROCEEDING TO SET UP THE MACHINE IN YOUR
SHOP.
7
1
2
Assemble the SuperMax Tools 19-38 drum sander Open Stand #71938-OP or
alternatively, if you have chosen to use your own bench prepare the existing
bench for the sander attachment.
NOTE: See Open Stand #71938-OP manual included in the Open Stand shipping box
for stand set-up and directions.
Open box 1 that contains the main sanding unit. Remove the cardboard liner.
Open the plastic bag enclosing the sanding unit.
NOTE: There will be a small container of hardware included with your sander.
This container will include everything you need to set up your sander (see
above).
3
4
Cut each corner of BOX 1 to fold sides flat, providing With one or two helpers, place the sanding unit on
access to sanding unit.
stand or bench (lift points marked).
5
Remove the two wooden packing plates from bottom of the sanding unit using the enclosed wrench and keep wrench for future adjustments.
NOTE: These bolts that you just removed from the packing plates will work as your bolts for attaching the sander or as extra bolts for future replacement.
8
6
7
Install knob to height adjustment handle. First, finger tighten nut to knob. Thread stud from knob into hand wheel and tighten nut against hand wheel.
Turn the handle and raise sanding head to higher position to remove packing block from under carriage arm.
CLOSE-UP
8
9
To prepare the unit for the installation of the conveyor
belt, first remove the 2 bolts on the outboard (left) side of the conveyor
belt.
Next remove the 2 bolts on the inboard (right) side of the conveyor belt.
10
NOTE: Leave the silver plate, which is near the fast lever and under the motor, in place when removing bolts.
Open box 2 and remove conveyor from packaging and place on sanding unit. The conveyor motor should be nearest to the main motor and depth gauge.
9
NOTE: The fast lever should be in the upright position for installation of the sanding unit. The fast lever raises the inboard (right) side of conveyor up. Do not ever tighten the bolts all the way down. The fast lever should always be able to be moved back and forth between and up/down position. The bolts should be tightened, but not so tight that the fast lever doesn’t move. The lever should be able to move from the down to up position easily.
11
12
Install lock washer and flat washer onto two socket heads (or hex head bolts) and install into flange of conveyor bed on inboard (right) (motor side). Keep support plate in place on inboard (right) side and make sure the fast lever is positioned up.
Install two lock washers and two flat washers on the studs on outboard (left)
side of the conveyor belt, then tighten all nuts and bolts with wrench.
NOTE: Do not completely tighten bolts with fast lever. See note above.
13
14
Plug the short power cord that is attached to the motor into the outlet on the control box. This cord will provide switched power for the motor when the machine is plugged into the power source.
Check your power supply to make sure that it is adequate (110 V, 20 A required) but do not plug the machine into the power supply until it is fully set-up.
10
SETTING UP YOUR DRUM SANDER
Your SuperMax Tools 19-38 sander should now be in place and ready for the
final set-up. The sander was adjusted and aligned at the factory. However
simple alignment checks will ensure that everything is in perfect order.
Problems can be avoided if these essential checks and set-up procedures are
performed prior to operation.
CHECKING DRUM ALIGNMENT
Checking the alignment before using the sanding drum is necessary to make sure
that the drum is parallel.
1
2
Remove the abrasive on the drum. Removing the abrasive is necessary to make sure that the adjustment is as accurate as possible and the texture on the abrasive will make the adjustment imprecise.
Locate the height adjustment handle for raising and lowering the sanding head.
NOTE: The height adjustment handle controls the drum height. Turning the
handle raises or lowers the sanding head. One revolution of the handle raises
or lowers the head by 1/16 of an inch.
3
4
Use a flat, uniform piece of wood as a thickness gauge. Insert it between the
conveyor belt and the drum on the inboard (right) side of the machine.
The tension rollers are set just below the drum enough so that items cannot
pass easily underneath. Use the height adjustment handle as necessary to
ensure that the piece of wood makes contact with the drum
After you place the piece of wood between the conveyor belt and the drum,
rotate the height adjustment handle up one full turn. After the height has
been adjusted the wood piece may be removed.
NOTE: You have to repeat these steps on the outboard (left) side of the
machine using the same procedure. As you check look to make sure that the drum
is parallel. A simple visual check that the drum is parallel is sufficient.
11
If the drum is not parallel, loosen the 4 socket head
screws A (these screws are along the outboard (left)
side of the conveyor belt) and raise or lower the conveyor with the adjustment nut B to achieve parallel
B
alignment. Then tighten the four socket head screws.
To achieve parallel alignment on the inboard (right)
side of the machine, repeat steps 3 and 4, then adjust
the alignment if needed by loosening the 4 socket
head screws located along the outboard (left) side of the conveyor and turning the height adjustment nut of
A
the conveyor.
5
CONNECTING DUST COLLECTORS
Dust collection is necessary for the SuperMax Tools 19-38 drum sander. The
sander comes equipped with a 4″ diameter dust exhaust port at the top of the
cover. Check to make sure that the minimum dust requirements are sufficient.
To attach to your collection system, install 4″ hose from your collector. The
minimum recommended dust collector capacities is 600 cfm. For best results,
follow the recommendations of the manufacturer of your dust collection
equipment. When connecting dust collectors straight pipe is preferred because
it is the least restrictive for airflow. If straight pipe is not possible Y’s
and elbows are preferred because they are less restrictive to airflow than
T’s.
NOTE: Some applications will require more dust collection than the recommended
minimum.
POWER AND ELECTRICAL SAFETY
The SuperMax Tools 19-38 drum sander requires 110 V, single-phase 20 A
service. After the dust collection system is in place and the drum alignment
is checked your machine should be ready to be powered up and operated.
SAFETY NOTE: DO NOT REWIRE THE SUPERMAX TOOLS 19-38 DRUM SANDER TO 220 VOLT. ALWAYS DISCONNECT ELECTRICAL POWER BEFORE DOING ANY SERVICING OR ADJUSTING OF THE MACHINE.
ABRASIVE SELECTION GUIDE
GRIT COMMON APPLICATION
24 Grit 36 Grit 50 Grit 60 Grit 80 Grit 100 Grit 120 Grit 150 Grit 180 Grit 220 Grit
Abrasive planing, surfacing rough-sawn boards, maximum stock or glue removal Abrasive planing, surfacing rough-sawn boards, maximum stock or glue removal Surfacing and dimensioning boards, trueing warped boards Surfacing and dimensioning boards, trueing warped boards Light dimensioning, removal of planer ripples Light surfacing, removal of planer ripples Light surfacing, minimal stock removal Finish sanding, minimal stock removal Finish sanding only, not for stock removal Finish sanding only, not for stock removal
12
INSTALLING AND WRAPPING ABRASIVES
Accurate attachment of the abrasive strip to the drum is critical to achieving
the top performance from your SuperMax Tools 19-38 drum sander.
WRAPPING ABRASIVES
Abrasive strips do not have to be pre-measured. The end of the roll is first
tapered and attached to the outboard (left) side of the drum. Then the strip
is wrapped around the drum, and the second taper is made for attachment to the
inboard (right) side of the drum. To attach a strip to the drum, follow the
procedure below.
Drum width: 19″ Tip-to-tip: 114-1/2″ Wrap ready to install: 108-1/2″
3”
TBAaPndEeRaEbDrasEivNe D(côOtéFabTrHasEif vAeBrsRleAhSauIVt) E
15-3/4″
Approx. 3” NOTE: Pre-cut wraps have been factory tapered to the specific width of your drum. If you are cutting your own abrasive, use the wrap that came on the drum as a template or the template below (abrasive side up).
1
2
Mark and cut a taper at one end of the roll as shown above. Because the
tapered end should use most of the left (outboard) slot width, its end must be
trimmed. Start on the left (outboard) side of the drum.
Pinch or squeeze the clip lever on the left (outboard) side of the drum.
Insert the tapered end through the slot and into the fastener so that it uses
most of the width of the slot. Release the clip lever to securely hold the
wrap end in the fastener.
Wind the wrap around the drum, being careful not to overlap the windings. The
tapered cut of the wrap end should follow the edge of the drum.
Continue to wrap the abrasive in a spiral fashion by rotating the drum with
your left hand and guiding athe wrap with your right hand. Successive windings
of the wrap should be flush with previous windings without any overlap.
13
3
4
Pinch or squeeze the clip lever to open the clip, and
pull the take-up lever to the top. Insert the tapered end through the slot in
the inboard (right) end of the drum.
The take-up fastener is designed to automatically take up any slack caused by
stretching of the abrasive wrap. The abrasive wrap may stretch enough in use
to allow the take-up lever to reach its lowest position so it no longer is
able to maintain tension on the wrap.
If this occurs, it will be necessary to reset the take-up lever by raising it,
pushing the wrap end into the slot, and then releasing the clip lever.
PROPER ABRASIVE WRAP POSITION
NOTE: Take notice that for detail only the drum was removed to show the inboard (right) take-up fastener.
Position the abrasive wrap in the slot with sufficient room between the inside
of the slot and the tapered end of the wrap to allow it to be pulled into the
drum
as needed (see opposite picture). If enough space is not left between the wrap
and the inside of the slot the take-up fastener will not operate properly.
ABRASIVE WRAP TENSION ADJUSTMENT
The abrasive wrap may stretch enough in use to allow the take-up lever to
reach its lowest position. If this occurs then tension is not longer
maintained on the abra-
sive wrap. To fix this reset the take-up lever by raising it, pushing the
abrasive wrap into the slot and then releasing the clip lever.
MAXIMIZING ABRASIVE LONGEVITY
A sandpaper cleaning stick may be used to remove deposits and help extend the life of the abrasive. 1. To use the cleaning stick, operate the sanding drum with the dust cover open and dust collection on. 2. Hold the cleaning stick against the rotating drum and move it along the drum surface. 3. Use a shop brush to remove any cleaning stick remnants from the drums before resuming sanding operations.
FOR YOUR OWN SAFETY ALWAYS WEAR EYE PROTECTION WHILE PERFORMING ABRASIVE CLEANING AND TAKE ALL PRECAUTIONS TO AVOID ANY CONTACT WITH HANDS OR CLOTHING ON THE UNCOVERED.
14
OPERATING THE 19-38 DRUM SANDER
Your sander will be able to perform an infinite variety of sanding projects
all designed to your specifications. With some time and experimentation the
proper setting and technique for each job will become apparent.
DRUM DEPTH OF CUT
Determining the depth of cut is the most important operating procedure
decision. It may take some experimentation to determine the proper depth of
cut. The crucial variables to keep in mind are abrasive grit, type of wood,
project type, and conveyor feed rate. We recommend practicing on a scrap of
wood prior to sanding a project.
· Depth Scale Operation
The depth scale (see opposite picture) measures the distance between the
conveyor table and the bottom of the sanding drum. The sanding head must be
parallel to the conveyor bed surface.
1. To calibrate the depth scale, loosen the two screws holding the scale.
Lower the drum (with abrasive installed) until the drum touches the conveyor
belt.
2. Slide the scale to align with the pointer at the “0” mark. Tighten the two
screws holding the scale.
An optional DRO (digital read out) for depth is available (see opposite
picture). This offers the most precise reading of sanded thickness and allows
for accurate repeatability of a thickness. Great when making parts that must
be an exact thickness or when matching a thickness.
1. To operate, turn ON and select standard inch “in” or metric millimeter
“mm”.
2. Lower drum, with abrasive installed, until it touches the conveyor belt.
Press “zero” button to calibrate.
· Using Thickness Gauge
Another method to set depth of cut is to use the thickness gauge attached to
the inboard (right) side of the sander (see opposite picture). The gauge must
be adjusted to the same height as the abrasive in use.
1. Place a flat piece of scrap stock under the drum with the abrasive in
place. Lower the durm until the abrasive lightly touches the scrap piece of
stock.
2. Without changing the height, place the scrap stock under the thickness
gauge. Adjust the bottom of the gauge by loosening the large nut and rotating
the gauge up or down until it lightly touches the scrap piece of stock.
3. Tighten the large nut. Now the stock can be placed under the thickness
gauge and the drum lowered until the gauge lightly touches the stock to be
sanded. By using this method the stock does not need to be carried under the
drum to set depth of cut.
A good rule of thumb when sanding is to place the stock under the drum and
lower the sanding head until the stock is in contact with the drum but the
drum can still be rotated by hand. Normally as the depth of cut is adjusted
the handle will be rotated no more than a third of a turn at any time.
INTELLISAND will help with this process.
15
CONVEYOR AND SPEED RATE
After the depth of cut has been determined, selecting the proper feed rate is
essential. For finish sanding the best finish is usually achieved with a slow
to moderate feed rate. This allows for the most revolutions of the drum per
inch of sanding. Faster feed rates can be used as long as the machine is not
over-stressed.
When finish sanding with grits finer than 80, the best finish can usually be
obtained if INTELLISAND does not engage. If INTELLISAND does slow the conveyor
when finish sanding, it is best to make another sanding pass without changing
the thickness setting and sand again.
NOTE: INTELLISAND will automatically adjust the conveyor feed rate if an
excess load is detected. This prevents excessive gouging, reduces the risk of
burning and protects the machine from overload or stalling. The red light by
the adjustment knob will come on when INTELLISAND is operating. When the load
is decreased, INTELLISAND will automatically increase the feed rate to the
pre-selected speed.
STOCK FEEDING OPERATION
To feed stock through the sander rest the stock and hold the stock to be
sanded on the conveyor table. Allow the conveyor to carry the stock into the
drum. Once the stock is halfway through, reposition yourself to the outfeed
side of the machine to receive and control the stock as it exits the unit.
STOCK FEEDING MAXIMUM PERFORMANCE
The built-in versatility of the SuperMax Tools 19-38 drum sander allows it to
be used for a wide range of tasks. Learning to use the multiple controls to
make adjustments will allow you to fine tune the machine for maximum results
no matter what the job. The best results come from experimenting with
different machine adjustments to best fit the job at hand.
· Sanding stock wider than the drum
When dealing with stock that is wider than the drum the fast lever will be
very useful (see opposite picture). Wide stock may require extra space between
the drum and conveyor along the outboard (left) edge. The extra space will
help prevent and overlap line or ridge from developing along the sanded part
where it extends beyond the sanding drum.
Adjusting the fast lever approximately half-way between the full upright and
full downright position allows for easy alteration of the drum position in
relationship to the conveyor without changing the initial drum alignment. It
is a good idea to test a scrap piece of stock prior to sanding. If a line or
ridge is still visible after adjusting the fast lever additional adjustments
can be made to the drum alignment. After sanding stock wider than the drum the
fast lever should be adjusted back to the original position. The fast lever
should be put into the up position.
NOTE: The fast lever raises the inboard (right) side of the table .003. Never
tighten the bolts all the way down. The fast lever should always be able to be
moved back and forth between and up/down position. The bolts should be
tightened, but not so tight that the fast lever doesn’t move.
· Sanding multiple pieces simultaneously
When sanding multiple pieces at once, make sure to stagger or step the pieces
across the width of the conveyor belt. This position provides better contact
with the tension rollers. It is best to only process multiple pieces that are
all of a similar thickness. If there is a thickness difference the thinner
pieces may not come in contact with the tension rollers and may slip on the
conveyor belt
16
· Sanding Imperfect or Tall Stock To avoid bodily injury take special care
when sanding stock that is twisted, bowed or otherwise varied in thickness
from end to end. If possible support such stock as it is being sanded to keep
it from slipping or tipping. Use extra roller stand, assistance from another
person, or hand pressure on the stock to minimize potentially hazardous
situations. When sanding high or tall stock special attention is necessary to
prevent tipping or slippage. Extra care may be needed as the stock exits the
machine.
· Stock Feeding Position and Angle Positioning the stock at an angle will
allow the most effective stock removal and least loading on the abrasives.
Feeding stock straight through yields the widest sanding capacity and least
noticeable scratch pattern. Some pieces because of their dimensions will need
to be fed into the sander at a 90-degree angle, which will be perpendicular to
the drum. However, even a slight offset angle of the stock can provide for
more effective sanding. Final pass sanding should be done following the grain
pattern.
TENSION ROLLER PRESSURE
The tension roller pressure is factory set and should be adequate. However,
the pressure of each roller can be adjusted as needed. To increase the tension
turn the tension adjusting screw clockwise 1/4 revolution at a time. To
decrease tension turn the adjusting screw counter-clockwise 1/4 revolution at
a time (see opposite picture). NOTE: Too little pressure can result in
slippage of stock on conveyor belt or kick-back. Too much tension can cause
snipe when drum sanding.
TENSION ROLLER CONTACT ADJUSTMENT
The tension rollers are factory set for the most versatile use. 1. If
necessary, to adjust tension roller contact, loosen
the four socket head screws holding the tension roller brackets (two per side;
front and back shown in opposite picture). 2. Have abrasive wrapped on drum.
3. With machine unplugged, lower sanding drum until it rests on conveyor belt.
4. Raise drum 2 to 3 revolutions. 5. Tighten the four socket head screws (two
per side; front and back). 6. Raise drum up, off of the conveyor belt. 7. Set
drum for proper sanding height and process stock.
17
CONVEYOR BELT TENSION
Insufficient belt tension will cause slippage of conveyor belt on the drive
roller during sanding operation. The conveyor belt is too loose if it can be
stopped by hand pressure applied directly to the top of the conveyor belt.
Excessive belt tension can result in bent rollers, premature wearing of the
bronze bushings or conveyor belt
To adjust the tension of the conveyor belt, first adjust the take-up screw nut
on both sides of the conveyor to obtain approximately equal tension on both
sides of the belt when taut (see opposite picture).
CONVEYOR BELT TRACKING
Belt tracking adjustments are made while the conveyor belt is running. After
the proper belt tension is obtained turn the conveyor unit on and set it at
the fastest speed setting. Watch for a tendency of the conveyor belt to drift
to one side of the conveyor. To adjust the belt tracking, tighten the take-up
screw nut on the side the belt is drifting toward, and loosen the take-up
screw nut on the opposite side. Adjusting the take-up screw nuts on either
side of the conveyor allows belt-tracking adjustments to be made without
affecting belt tension. Note: Adjust the takeup screw nuts only 1/4 turn at a
time. Then allow time for the belt to react to the adjustments before
proceeding further. Avoid over-adjustments.
MAINTENANCE
MONTHLY MAINTENANCE CHECKLIST
· Lubricate conveyor bushings and check for wear.
· Lubricate with a dry lubricant spray all of the moving parts, such as
threaded rods and washers.
· Clean dust from conveyor belt.
· Check all set screws for tightness.
· Clean drum and abrasives if necessary.
REPLACING CONVEYOR BELTS
To replace the conveyor belt, the conveyor assembly must be removed from the
machine. 1. Raise the drum carriage to its highest position
using the height adjustment handle. 2. Turn off power source to machine.
Unplug main drive
motor from receptacle (in gear motor assembly). 3. Loosen the conveyor take-up
screws to relieve belt
tension and slide the drive roller fully inward. 4. Remove the two Allen head
bolts on the inboard
(right) side that attach the conveyor assembly to the base. 5. Remove the two
nuts and washers from outboard (left) side (see opposite picture). 6. Lift the
conveyor and remove it from the sander. Set conveyor on motor side. Avoid
tearing the belt on any edges underneath the conveyor bed during removal.
Reverse the procedure for re-installation. Re-install the conveyor bed to
sander.
18
CLEANING THE MACHINE
The sander may need to be cleaned more frequently depending upon frequency of
use. The drum and the conveyor belt need to be clean. Allowing excess build-up
of dust and debris can adversely affect performance and increase the
likelihood of slippage on the conveyor belt. Sweep the conveyor belt clean
after all operations. When cleaning dust from the drum leave the dust
collection system on.
SUPPLY CHECKLIST
ACCESSORIES
71938-CL 71938-OP 98-0130 71938-7 71938-DRO
CONVEYOR BELTS
Closed stand, includes locking wheels Open stand Caster Set, heavy duty, roll & swivel lock (used with open stand) Infeed/outfeed tables DRO (digital read out) depth scale
60-0322 (Type 1) 61-1003 (Type 2)
DRUM ABRASIVES
100 grit abrasive surface with reinforced backing (standard equipment) Polyurethane textured surface with monofilament backing
60-19-036 60-19-060 60-19-080 60-19-100 60-19-120 60-19-150 60-19-180 60-19-220 60-19-000
36 Grit 60 Grit 80 Grit 100 Grit 120 Grit 150 Grit 180 Grit 220 Grit Assorted box (36/80/120 grit)
SuperMax Tools 19-38 – 3-Wraps in Box SuperMax Tools 19-38 – 3-Wraps in Box SuperMax Tools 19-38 – 3-Wraps in Box SuperMax Tools 19-38 – 3-Wraps in Box SuperMax Tools 19-38 – 3-Wraps in Box SuperMax Tools 19-38 – 3-Wraps in Box SuperMax Tools 19-38 – 3-Wraps in Box SuperMax Tools 19-38 – 3-Wraps in Box SuperMax Tools 19-38 – 1 each in Box
NOTES
For information call SuperMax Tools 1-(888)-454-3401 or visit www.SuperMaxTools.com 19
TROUBLESHOOTING YOUR SUPERMAX TOOLS DRUM SANDER
Any operating problems with the drum sander will likely occur most often
during the period that you are becoming familiar with its components and their
adjustments. If you are experiencing a problem affecting the machine’s
performance, check the following listings for potential causes and solutions;
it may also pay to review the previous sections in this manual on setting up
and operating your machine.
TROUBLESHOOTING GUIDE: MOTORS
PROBLEM MOTOR DOES NOT START BRUSH MOTOR OVERLOADS
POSSIBLE CAUSE
Main power cord unplugged from receptacle
Drum motor cord unplugged from receptacle near power-
feed motor. Circuit fuse blown or circuit
breaker tripped Inadequate circuit
Machine overloaded
CONVEYOR MOTOR OSCILLATES
Motor not properly aligned Shaft collar or bushing worn
DRUM MOTOR OR CONVEYOR GEAR MOTOR
STALLS
Drive roller bent Excessive depth of cut
TROUBLESHOOTING GUIDE: CONVEYOR
SOLUTION
Plug in primary power cord
Plug in drum motor cord at receptacle on machine if so
equipped (Fig 5) Replace fuse or retrip breaker
(after determining cause) Check electrical requirements Use slower feed rate;
reduce
depth of cut Loosen housing bolts, run
motor, retighten bolts. Replace shaft collar or
bushing Replace drive roller
Reduce depth of cut; reduce feed rate
PROBLEM
CONVEYOR DRIVE ROLLERS RUN INTERMITTENTLY
CONVEYOR BELT SLIPS ON DRIVE ROLLER
POSSIBLE CAUSE
Shaft coupling loose
Improper conveyor belt tension
Excessive depth of cut
SOLUTION
Align shaft flats of gear motor and drive roller; tighten shaft coupling set
screws
Adjust belt tension
Reduce depth of cut reduce feed rate
20
PROBLEM
POSSIBLE CAUSE
STOCK SLIPS ON CONVEYOR BELT CAUSING
GOUGING
Excessive depth of cut Tension rollers too high
Excessive feed rate
Dirty or worn conveyor belt
CONVEYOR MOTOR STALLS
Belt out of adjustment Roller bushings elongated
due to excessive wear
TROUBLESHOOTING GUIDE: MACHINE
PROBLEM DRUM HEIGHT ADJUSTMENT WORKS IMPROPERLY KNOCKING SOUND WHILE
RUNNING
SNIPING OF WOOD (GOUGING NEAR END OF BOARD)
BURNING OF WOOD OR MELTING OF FINISH
CONVEYOR MOTOR STALLS
POSSIBLE CAUSE
Improper adjustment of height control
Bearing worn
Inadequate support of stock
Conveyor drive or driven rollers higher than conveyor bed
Exessive tension roller pressure
Feed rate too slow
Excessive depth of cut
Conveyor belt is too loose Excessive depth of cut
Wood slipping on conveyor due to lack of contact
SOLUTION
Reduce depth of cut Lower tension rollers
Reduce feed rate Clean or replace conveyor
belt Readjust belt Replace bushings
SOLUTION
Readjust height control
Replace bearing Contact distributor Use roller stands to sup-
port stock
Readjust rollers
Adjust rollers Increase feed rate Reduce depth of cut Adjust belt tension
Reduce depth of cut Use alternate feeding
procedure
21
19-38 – WIRING DIAGRAM 22
TO GEAR MOTOR CONVEYOR
GROUND STUD
19-38 – PARTS LIST – HEAD ASSEMBLY
…….PART NO…………..DESCRIPTION…………………………………………….. SIZE …………………………………………..QTY
1……. 480DS-101 ……….. MOTOR……………………………………………………………………………………………………………………………. 1 ……… 480DS-101 ………. MOTOR FAN COVER ……………………………………………………………………………………………………….. 1 2……. 480BS-134 ……….. STRAIN RELIEF, MOTOR…………………………………… 7N-2……………………………………………………. 1 3……. 480DS-103 ……….. MAIN CORD, MOTOR TO CONTROL BOX ……………………………………………………………………….. 1 4……. 480BS-104 ……….. KEY…………………………………………………………………… 3/16″ SQ X 3/4″ ………………………………….. 2 5……. 480BS-105 ……….. NYLON INSERT LOCK NUT………………………………. 5/16″ – 24 ……………………………………………. 4 6……. 480BS-106 ……….. FLAT WASHER …………………………………………………. 5/16″…………………………………………………… 9 7……. 480BS-107 ……….. OILITE WASHER………………………………………………………………………………………………………………. 8 8……. 480BS-108 ……….. MOTOR PLATE………………………………………………………………………………………………………………… 1 9……. 480BS-109 ……….. SET SCREW ……………………………………………………… #8-32 X 1/4″……………………………………….. 1 10….. 480BS-110 ……….. HEX CAP SCREW……………………………………………… 5/16″ – 18X1-1/4″ ……………………………….. 6 11….. 480BS-111 ……….. LOCK WASHER ………………………………………………… 3/8″…………………………………………………….. 4 12….. 480BS-112 ……….. SOCKET HEAD CAP SCREW ……………………………. 3/8″ – 16X1-1/2″………………………………….. 4 13….. 480BS-113 ……….. SET SCREW ……………………………………………………… 1/4″-20X1/4″………………………………………. 5 14….. 480BS-114 ……….. COUPLING ………………………………………………………………………………………………………………………. 2 15….. 480BS-115 ……….. COUPLING SPIDER………………………………………………………………………………………………………….. 1 16….. 480BS-116 ……….. DEPTH SCALE PLATE……………………………………………………………………………………………………… 1 17….. 480BS-117 ……….. SCREW, PHIL PAN HEAD………………………………….. M4X0.7X6………………………………………….14 18….. 480BS-118 ……….. LABEL, DEPTH SCALE (INCH)…………………………………………………………………………………………. 1 19….. 480BS-119 ……….. DEPTH SCALE POINTER…………………………………………………………………………………………………. 1 20….. 480BS-120 ……….. KNOB ………………………………………………………………………………………………………………………………. 1 21….. 480BS-121 ……….. HEIGHT ADJUSTMENT HANDLE……………………………………………………………………………………. 1 22….. 480BS-122 ……….. NYLON INSERT LOCK NUT………………………………. 5/8″-11 ……………………………………………….. 1 23….. 480BS-123 ……….. HEIGHT ADJUSTMENT SCREW ………………………. …………………………………………………………… 1 24….. 480BS-124 ……….. E-RING………………………………………………………………. E12……………………………………………………… 1 25….. 480BS-125 ……….. THRUST BEARING……………………………………………. 51103 …………………………………………………. 1 26….. 480BS-126 ……….. SHROUD………………………………………………………………………………………………………………………….. 1 27….. 480BS-127 ……….. STUD……………………………………………………………………………………………………………………………….. 4 28….. 480BS-128 ……….. HEX CAP SCREW……………………………………………… 3/8″-16X1-1/4″……………………………………. 4 29….. 480BS-129 ……….. FLAT WASHER …………………………………………………. 3/8″…………………………………………………….. 8 30….. 480BS-130 ……….. HINGE ……………………………………………………………………………………………………………………………… 2 31….. 480DS-131 ……….. DUST COVER…………………………………………………………………………………………………………………… 1 32….. 480BS-132 ……….. HANDLE ………………………………………………………………………………………………………………………….. 1 33….. 480BS-133 ……….. PAN HEAD MACHINE SCREW ………………………….
8X1/2″………………………………………………. 2 34….. 480DS-134 ……….. LOCK WASHER
………………………………………………… M3………………………………………………………. 2 35….. 480BS-135 ……….. DUST
COVER LATCH ………………………………………………………………………………………………………. 1 36….. 480DS-136 ………..
PHILLIPS FLAT HEAD SCREW …………………………. M3X0.5X10 ………………………………………… 2 37…..
480DS-137 ……….. SANDING DRUM……………………………………………………………………………………………………………… 1 38…..
480DS-138 ……….. NYLON INSERT LOCK NUT………………………………. M3X0.5 ……………………………………………….
2 39….. 480DS-139 ……….. INBOARD (RIGHT) ABRASIVE FASTENER
………………………………………………………………………. 1 40….. 480DS-140 ……….. OUTBOARD (LEFT) ABRASIVE
FASTENER……………………………………………………………………… 1 41….. 480DS-141 ……….. CARRIAGE BOLT
………………………………………………. 5/16″-18X1…………………………………………. 4 42….. 480DS-142 ………..
BEARING …………………………………………………………. 6205ZZ……………………………………………….. 2 43….. 480DS-143
……….. C-RING ……………………………………………………………… S25……………………………………………………… 2 44…..
480DS-144 ……….. DRUM CARRIAGE ……………………………………………………………………………………………………………. 1
45….. 480BS-145 ……….. FLAT WASHER ………………………………………………….
1/4″…………………………………………………….. 5
23
19-38 – PARTS LIST – HEAD ASSEMBLY
…….PART NO…………..DESCRIPTION…………………………………………….. SIZE …………………………………………..QTY
46….. 480BS-146 ……….. ROUND SOCKET HEAD CAP SCREW ……………….
1/4″-20X1″………………………………………….. 4 47….. 480BS-147 ……….. FLAT WASHER
…………………………………………………. 5/16″…………………………………………………… 4 48….. 480DS-148 ……….. BEARING
SEAT ……………………………………………………………………………………………………………….. 2 49….. 480BS-149 ……….. HEX
CAP SCREW WITH WASHER……………………. #10-24X3/8″ ………………………………………. 2 50….. 480BS-150
……….. DUST COVER CATCH………………………………………………………………………………………………………. 1 51…..
480BS-151 ……….. STUD……………………………………………………………………………………………………………………………….. 1 52…..
480BS-152 ……….. SPRING……………………………………………………………………………………………………………………………. 1 53…..
480BS-153 ……….. TENSION ROLLER …………………………………………………………………………………………………………… 2
54….. 480BS-154 ……….. BUSHING, OILITE
…………………………………………………………………………………………………………….. 4 55….. 480BS-155 ……….. TENSION
ROLLER BRACKET, INNER LEFT……………………………………………………………………… 1 56….. 480BS-156 ………..
SCREW……………………………………………………………… #8-32X1″…………………………………………….. 4 57….. 480BS-157
……….. SPRING, TENSION ROLLER …………………………………………………………………………………………….. 4 58…..
480BS-158 ……….. TENSION ROLLER BRACKET, INNER RIGHT ……………………………………………………………………
1 59….. 480BS-159 ……….. PAD, BRACKET-TENSION
ROLLER…………………………………………………………………………………… 2 60….. 480BS-160 ………..
BRACKET…………………………………………………………………………………………………………………………. 2 61….. 480BS-161 ………..
PLATE ……………………………………………………………………………………………………………………………… 1 62….. 480BS-162 ………..
BASE ……………………………………………………………………………………………………………………………….. 1 63….. 480BS-163
……….. ADJUSTING LEVER (FAST)……………………………………………………………………………………………… 1 64…..
480BS-164 ……….. ADJUSTING ROD…………………………………………………………………………………………………………….. 1
65….. 480BS-165 ……….. HEIGHT ADJUSTING PLATE
…………………………………………………………………………………………… 1 66….. 480BS-166 ……….. ROUND SOCKET HEAD
CAP SCREW ………………. 5/16″-18X1/2″…………………………………….. 4 67….. 480BS-167 ……….. LOCK
WASHER ………………………………………………… 5/16″…………………………………………………… 5 68….. 480BS-168 ………..
SPRING……………………………………………………………………………………………………………………………. 3 69….. 480BS-169 ………..
NYLON INSERT LOCK NUT………………………………. 1/4″-20 ……………………………………………….. 1 70…..
480DS-170 ……….. SOCKET HEAD CAP SCREW ……………………………. M8X1.25X40……………………………………….
1 71….. 480DS-171 ……….. HEX NUT WITH WASHER………………………………….
5/16″-18……………………………………………… 4 72….. 480DS-172 ……….. BLOCK, MEASURING
DEVICE………………………………………………………………………………………….. 1 73….. 480DS-173 ……….. HEX
NUT…………………………………………………………… M12X1.75…………………………………………… 1 74….. 480DS-174 ………..
STOP BOLT………………………………………………………………………………………………………………………. 1 75….. 480DS-175
……….. SCREW……………………………………………………………… M3X0.5X6…………………………………………… 2 76…..
480DS-176 ……….. LOWER FIXED PLATE, DRO……………………………………………………………………………………………… 1
77….. 480BS-177 ……….. HEX CAP SCREW………………………………………………
3/8″-16X3/4″………………………………………. 4 78….. 480DS-178 ……….. HEX
NUT…………………………………………………………… M4X0.7 ………………………………………………. 1 79….. 480BS-179 ………..
TENSION ROLLER BRACKET, RIGHT ………………………………………………………………………………. 1 80…..
480BS-180 ……….. TENSION ROLLER BRACKET, LEFT…………………………………………………………………………………. 1
81….. 480BS-181 ……….. E-RING……………………………………………………………….
E5……………………………………………………….. 1 82….. 480DS-182 ……….. UPPER FIXED PLATE,
DRO………………………………………………………………………………………………. 1 83….. 480DS-183 ……….. BATTERY
COVER…………………………………………………………………………………………………………….. 1 84….. 480DS-184 ……….. LABEL
……………………………………………………………………………………………………………………………… 1 85….. 480BS-185 ………..
HEIGHT DIRECTION LABEL…………………………………………………………………………………………….. 1 86….. 480BS-186
……….. MAINTENANCE LABEL …………………………………………………………………………………………………… 1 87…..
480BS-187 ……….. WARNING LABEL…………………………………………………………………………………………………………….. 1
88….. 480DS-188 ……….. BATTERY ………………………………………………………………………………………………………………………….
1 89….. 480DS-189 ……….. DIGITAL READOUT ASSEMBLY
(OPTIONAL)………………………………………………………………….. 1 90….. 635DS-280 ……….. FASTENER TOOL
(OPTIONAL)………………………………………………………………………………………… 1
24
19-38 – HEAD ASSEMBLY 25
19-38 – PARTS LIST – CONVEYOR AND MOTOR
…….PART NO…………..DESCRIPTION…………………………………………….. SIZE …………………………………………..QTY
1……. 480BS-201 ……….. GEAR MOTOR…………………………………………………… 90 VDC……………………………………………….. 1 2……. 480DS-202 ……….. STRAIN RELIEF, POWER CORD………………………… 6P3-4………………………………………………….. 1 3……. 480DS-203 ……….. POWER CORD …………………………………………………………………………………………………………………. 1 4……. 480BS-204 ……….. FLAT WASHER …………………………………………………. 5/16″…………………………………………………… 4 5……. 480BS-205 ……….. SOCKET HEAD CAP SCREW ……………………………. #10-32X1/2″ ………………………………………. 4 6……. 480BS-206 ……….. TRACKER KIT (OPTIONAL)……………………………………………………………………………………………… 2 7……. 480BS-207 ……….. KNOB ………………………………………………………………………………………………………………………………. 1 8……. 480BS-208 ……….. SPEED ADJUSTEMENT LABEL……………………………………………………………………………………….. 1 9……. 480BS-209 ……….. WIRING GUARD……………………………………………………………………………………………………………….. 1 10….. 480DS-210 ……….. CONTROLLER………………………………………………………………………………………………………………….. 1 11….. 480DS-211 ……….. CONTROL HOUSING BRACKET………………………………………………………………………………………. 1 12….. 480BS-212 ……….. PAN HEAD SELF-TAPPING SCREW …………………. 5/32″X1/2″ …………………………………………. 2 13….. 480DS-213 ……….. RECEPTACLE, MAIN CORD …………………………………………………………………………………………….. 1 14….. 480BS-214 ……….. SCREW……………………………………………………………… #10-32X1/2″ ………………………………………. 1 15….. 480BS-215 ……….. WASHER, LOCK-INT. TOOTH ……………………………. #10……………………………………………………… 2 16….. 480BS-216 ……….. HEX NUT…………………………………………………………… #10-32………………………………………………… 2 17….. 480BS-217 ……….. SCREW, HEX HEAD SLOTTED………………………….. #10-32X3/8″ ………………………………………. 5 18….. 480BS-218 ……….. SCREW, PHIL PAN HEAD…………………………………..
6-32X1/2″…………………………………………. 2 19….. 480BS-219 ……….. SWITCH ON/OFF
…………………………………………………………………………………………………………….. 1 20….. 480BS-220 ……….. COUPLER,
SHAFT……………………………………………………………………………………………………………. 1 21….. 480BS-113 ……….. SET
SCREW ……………………………………………………… 1/4″-20X1/4″………………………………………. 2 22….. 480BS-222
……….. BRACKET, BASE-CONTROLLER………………………………………………………………………………………. 1 23…..
480BS-223 ……….. COVER, BASE-CONTROL HOUSING………………………………………………………………………………… 1
24….. 480BS-224 ……….. HEX CAP SCREW………………………………………………
1/4″-20X3/4″……………………………………..12 25….. 480BS-225 ………..
WASHER,WAVE………………………………………………… 1/4″…………………………………………………….. 4 26….. 480BS-145
……….. FLAT WASHER …………………………………………………. 1/4″…………………………………………………….. 4 27…..
480BS-227 ……….. BRACKET, TAKE UP-SLIDE………………………………………………………………………………………………. 2
28….. 480BS-154 ……….. BUSHING, OILITE
…………………………………………………………………………………………………………….. 4 29….. 480BS-229 ……….. ROLLER,
DRIVEN……………………………………………………………………………………………………………… 1 30….. 480BS-230 ………..
WRENCH…………………………………………………………………………………………………………………………. 2 31….. 480BS-231 ………..
HEX NUT…………………………………………………………… 1/4″-20 ……………………………………………….. 2 32….. 480BS-232
……….. WASHER, LOCK-INT. TOOTH ……………………………. 1/4″…………………………………………………….. 2 33…..
480BS-233 ……….. SCREW, ROUND HEAD-SLOTTED……………………..
1/4″-20X1-3/4″……………………………………. 2 34….. 480BS-234 ……….. BRACKET, TAKE UP-
BASE……………………………………………………………………………………………….. 2 35….. 480BS-167 ……….. LOCK WASHER
………………………………………………… 5/16″…………………………………………………… 4 36….. 480BS-236 ……….. ROLLER,
DRIVE………………………………………………………………………………………………………………… 1 37….. 480BS-237 ………..
BRACKET, SUPPORT-DRIVE ROLLER ………………………………………………………………………………. 1 38…..
480BS-238 ……….. BED, CONVEYOR……………………………………………………………………………………………………………… 1
39….. 480BS-239 ……….. SOCKET HEAD CAP SCREW …………………………….
5/16″-18X3/4″…………………………………….. 2 40….. 480DS-240 ……….. BELT CONVEYOR, ABRASIVE
(NOT SHOWN)…………………………………………………………………. 1 41….. 480BS-204 ……….. FLAT WASHER
…………………………………………………. 5/16″…………………………………………………… 1 42….. 480BS-242 ……….. HEX
NUT…………………………………………………………… 5/16″-24……………………………………………… 1 43….. 480BS-243 ………..
SLOTTED SET SCREW……………………………………… #8-36X5/16″ ………………………………………. 1 44…..
480BS-244 ……….. STRAIN RELIEF, GEAR MOTOR ………………………… 6N-4…………………………………………………….
1 45….. 480BS-245 ……….. HEX NUT……………………………………………………………
5/16″-18……………………………………………… 2
26
19-38 – CONVEYOR AND MOTOR 27
SuperMaxTools.com – sales@SuperMaxTools.com
P. 1-888.454.3401 – F. 1-651.454.3465
References
- SuperMax Tools | Superior Quality. Affordable Efficiency.
- SuperMax Tools | Superior Quality. Affordable Efficiency.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>