AODSK AED-403 Multifunctional Electronic Drum User Manual
- June 15, 2024
- AODSK
Table of Contents
AODSK AED-403 Multifunctional Electronic Drum
FUNCTION INTRODUCTION
Thank you for choosing our electronic drum. Elegant and delicate electronic drum is the perfect combination of modern new electronic technology. Before using this product, you must read the instructions in detail.
- The maximum number of pronunciations is 32, with 6 layers.
- support bass drum kick, military drum snare, Tonggu tom1 -3, high pitched cymbal crash and tinkling cymbal ride Hi hat control pedal.
- 15 drum sets, 165 timbres.
- 30 songs.
- support the adjustment of sensitivity parameters of each drum.
- three teaching modes.
- speed control: 30 ~ 250 beats/ min.
- metronome: 1 ~ 4 types.
- other functions: parameter storage, reset and recording.
- three digit LED display.
- interface: power supply DC, usbmidi, earphone, audio input, audio output.
REMARK!
- This product is an electro-acoustic instrument product. It is normal that there is a little current sound in the speaker or earphone after power-on. Keep away from “radio, TV, antenna receiver, router, refrigerator, TV, motor and other RF electrical interference sources” during use .
INSTALLATION GUIDE
REMARK!
- Please follow the instructions and read the “safety precautions” in the User Manual carefully before using it.
- This product needs adult to install, do not let the minor install it independently.
HOST BOX SOCKET DIAGRAM
POWER TERMINAL CONNECTION
- When in use, connect the power terminal according to the diagram, insert the power outlet of the module box at one end and 100-240V household power outlet at the other end. (Fig. 1)
- If you do not use this product for a long time, please pull out the power plug and keep it properly.
USB MIDI PORT
The use of electronic drum MIDI USB interface can interact with music devices with MIDI.
- Through the pre-installed Music software on computers and mobile phones, we can learn to play, compose music, store and other functions. (Fig. 2)
- When connected to a computer or mobile phone, the audio output of the device needs to be connected to the audio input socket of the module box in order to synchronize the sound effects on the device. (Fig. 5)
AUDIO OUTPUT PORT
Audio output port can be connected with active speaker (special electronic drum speaker) and large audio equipment. (Fig. 3)
AUDIO INPUT PORT
Audio input port can connect the sound source playback device to the module box for playback (such as MP3. mobile phone and other audio signal input). (Fig. 4)
EARPHONE PORT
Connecting headphones monitors the details of percussion and does not disturb others when playing without connecting speakers. (Fig. 5)
REMARK!
- To prevent damage to the equipment, make sure to turn down the volume and shut down all the equipment before making any connection.
- Additional cymbals, speakers, headphones and peripherals are all purchased separately. They are not in standard configuration.
OPERATION GUIDE Power on
- Turn the switch to on, the display will light up and the host will be turned on.
- Turn the switch to off again, the display goes out and the host is turned off.
Durm group selection
- Start up and enter the default drum group selection 01 (drum group No. 01). Use the data wheel to select the addition and subtraction of drum group.
- Or press the < kit > key directly, the screen will jump to 01 (drum group number), and then
use the data wheel or< + > < -> button to select the drum group.
Metronome
- Press the < click > key to play the metronome, and press the < click > key again to stop playing.
- Press the< metronome> button, the indicator light jumps to the “metronome” button on the second left to enter the metronome mode, and the screen displays 120 (speed value). Turn the data wheel or < + > < -> button to change the metronome speed.
- Press the < Select > key in metronome mode, and the screen will jump to the metronome parameter adjustment interface. You can press the< + > < -> button to select the parameters you want to adjust: r.4 (beat type), B04 (beat number), L25 (metronome volume), and then turn the data wheel to adjust the parameters.
- After parameter adjustment, press the < Select > key to confirm and exit the parameter interface (the metronome speed value is associated with “coach” mode and “song” mode).
COACH mode
The “coach” training mode of this product can help establish speed, accuracy and endurance, and help cultivate the practice function of a better sense of rhythm,Make progress under the supervision of “coach” coach mode! Press the “coach” button to enter the coach mode. In this mode, there are three practice modes. Press the data wheel or < + > < -> Button to select the practice mode.
-
Exercise mode 1: C-1 beat detection exercise: beat the drum at a fixed speed to train the accuracy of the blow.
-
Practice mode 2: C-2 silent strike mode: the metronome will sound one section and mute one section to train when there is no beat Hit accuracy at the prompt of the drill is an advanced version of exercise mode 1.
-
Practice mode 3: C-3 speed strike practice, the metronome will automatically change the speed from the slowest to the fastest, and then from the fastest Express speed is reduced to the slowest speed to practice combat endurance.
-
Press the < coach > button, the indicator light will jump to the left three “coach” buttons, and the screen will display C-1 (practice mode 1) when hitting Value practice, turn the coding wheel to switch the other two practice modes C-2 and C-3
-
At this time, press the< click> key, the metronome sounds and starts to knock the drum for practice.
-
After four preliminary beats, the display will show.
-
After the exercise, the score of the whole hitting exercise will be displayed, with 0-100 points to evaluate the accuracy of the current exercise. 2
-
Press the < Select > key in the C-1 mode to enter the parameter setting interface. You can adjust the number of practice sections in the practice mode as required The number of sections to practice determines the length of this exercise.
-
Press the < Select > key in the C-2 mode to enter the parameter setting interface. You can adjust the number of practice sections in the practice mode as required The number of sections to practice determines the length of this exercise.
-
Press the < Select > key in C-3 mode to enter the parameter setting interface. You can adjust the variables of the current bpm. The variables are changed each time Speed value.
-
During the practice, you can press the < click > key again to stop the practice.
SONG mode
- Press the < > key to start playing songs, and press the < > key again to temporarily stop playing.
- Press the < Song > button to enter the song mode. When the indicator light jumps to the left four “song” buttons, the screen displays 01 (song number).
- Turn the data wheel or press the < + > < – > button to select the song to play.
- Press the < Select > key in the song mode, and the screen will jump to enter the song parameter setting interface. The drum sound of the Etude can be turned off by default On: select on / off by turning the data wheel or pressing the < + > < – > button.
- After parameter adjustment, press the < Select > key to confirm and exit the parameter interface.
Drum parameters
- Press < kit >, the indicator light jumps to the left “kit” button. When the screen jumps to 01 (drum group number), press < Select > to enter Drum parameter adjustment mode.
- Tap the drum disc you want to adjust, and then press the < + > < – > button to select the sensitivity option you want to adjust: S03 (surface sensitivity)T05 (trigger threshold), CO5 (crosstalk threshold), R05 (repeated trigger), V01 (drum force curve), L25 (drum volume)
- Change the parameters by rotating the data wheel, long press the < – > key, the screen displays
sav, and these parameters are saved successfully.
All drum settings of this product are factory settings, which have been corresponding to the audio of the sound source box. Without drum, it is insensitive, triggered for many times and cascaded There is no need to change the drum parameters in case of interference. If other drums are insensitive, triggered for many times, crosstalk, etc. after adjustment, you can press and holdPress < + > to restore the factory settings.
Recording function
1. Press the < rec > button when the indicator light is in “kit” and “click”
status, and the screen displays the word “REC” in respiratory flashing status,
Enter the recording preparation state.
2. Tap any drum and the metronome sounds. At this time, the screen displays
“—” in breathing flashing state and starts recording.
3. Press the < rec > key or < play > key again, the recording stops and “A-1”
is displayed on the screen.
4. Press < > to start playing the current recording, and press again to stop
playback
5. If you enter the recording preparation state again without any knocking,
the “A-1” recorded last time is played back.
Save / reset
- Press and hold < – > key, sav will be displayed on the screen and saved successfully.
- Press and hold the < + > key, the screen displays res, the reset is successful, and the factory setting is restored
USBMIDI
- Use the usb-b data cable to plug in the USB interface and connect it to the PC end.
- Select the MIDI device.
**APPENDIX
** Drum combination timbre User
drum group
- Funk
- Original
- Poprock
- Rock
- Seesion
- SpeedMetal
- ClassicDry
- Modern
- Jazz
- Blues
- Popular
- Fuse
- Dancehall
- Synthgaze
- Standard
Demonstration music
PRODUCT MAINTENANCE
Careful maintenance and protection of the product, to extend the service life of the product, reduce the fault has a very important role.
AVOID HEATING, DAMPNESS OR DIRECT SUNLIGHT
Do not over expose the product to direct sunlight, or place it near air conditioning or extremely hot place.
DO NOT USE NEAR THE TV OR RADIO
This product may cause video or audio interference to the reception of TV and radio. If this happens, the product should be removed from the TV or radio.
NO DILUENTS OR SIMILAR CHEMICALS SHOULD BE USED FOR CLEANING
Clean the product with a soft cloth wetted with weak water solution and
neutral detergent.
Soak the cloth in a solution and wring it dry until it approaches drying.
DO NOT SHAKE, AVOID COLLISION
When moving, the product should be handled carefully and lightly. Violent vibration and collision are strictly prohibited in order to avoid damage to the shell or internal electronic components.
SAFETY PRECAUTIONS
POWER SUPPLY
This product can be powered by standard indoor wall sockets. Please only use the power cord specified in this product. When not in use, please turn off the power supply. When not in use for a long time, pull out the power cord and keep it properly.
SIGN
To ensure that you use this product safely and correctly, to prevent harm to users and others and financial damage, this manual and products are marked with a series of safety signs. The various signs and their meanings are as follows:
WARNING
This sign indicates that there is a potential risk of death or serious injury if this mark is ignored and the product is mishandled.
BE CAREFUL
This sign indicates that there is a potential danger of injury to personnel or other financial damage if this sign is ignored and the product is operated incorrectly.
EXAMPLE OF LOGO
-
This triangle sign indicates what users should pay attention to.
(The left example is careful shocks) -
A circular sign with an oblique line indicates prohibitions. The icons in or beside the logo indicate the contents specifically prohibited. (The example on the left is no disassembly)
-
The round black bottom sign indicates what must be observed. The diagrams in this sign indicate the contents of the specific matters that must be observed.
(The example on the left is that the power plug must be pulled out of the socket)
WARNING
Smoke, odor, overheating When the product smokes, smells or overheats, there is a danger of fire and electric shock when it is used continually. In case of the above situation, the following operations should be performed immediately:
- Turn off the power supply.
- Pull the plug out of the power outlet.
- Contact your dealer.
Power cord
- The improper use of power cord may cause fire and electric shock. The following precautions must be observed:
- The special power cord designated for this product must be used.
- The AC power supply with output voltage within the rated voltage range for household use must be used.
- Do not overload power sockets and extension lines.
- The improper treatment of power line will lead to its damage or breakage, which will cause fire and electric shock hazards. The following precautions must be observed:
- Do not place or heat heavy objects on power lines.
- Do not attempt to alter or bend the power cord too much.
- Do not twist or pull the power cord.
- If the power cord or plug is damaged, please replace the same type of power cord.
- Do not touch the power cord and plug with wet hands, otherwise there is a danger of electric shock.
- Please use the power cord where the water will not splash. Water is in danger of causing fire and electric shock.
- Never place vases or any other container containing water on this product. Water is dangerous of causing fire and electric shock.
- Do not allow minors to unplug and touch power lines or connection boards. Minors have no common sense of electricity safety, which may cause electric shock.
BE CAREFUL
The improper use of power cord may cause fire and electric shock. The following precautions must be observed:
- Never put the power cord near the oven or other heat source.
- Do not pull the cable when pulling out o the power socket. The main body of the plug must be grasped.
- The power cord plug must be inserted in the socket to the end.
- Make sure the power supply is off before connecting or disconnecting it.
- When thunderstorms occur or before traveling or other long-term departure, disconnect the power cord from the wal outlet.
- At least once a year, remove the power cord from the wall outlet and clean the dust accumulated around the plug.
Do not burn this product
Do not put this product in the fire, otherwise it will lead to product combustion and explosion of internal electronic components, which will cause fire and personnel injury.
Water and foreign bodies
Water, other liquids and (metal sheets, etc. entering this product are in
danger of causing fire and electric shock. In case of the above situation, the
following operations shall be performed immediately
- Turn off the power supply.
- If you are using a power cord for power supply, unplug it from the wall outlet.
- Contact your distributor.
Disassembly and transformation
Do not disassemble or transform the product in any way, otherwise there is a risk of electric shock, scald or other personal injury. All internal inspection, adjustment and maintenance operations should be entrusted to your distributor.
Falling or colliding
If the product falls or is damaged by stron impact, it will be in danger of causing fire and electric shock. In case of the above situation, the following operations shall b performed immediately:
1. Turn off the power supply.
2. If you are using a power cord for power supply, you need to unplug it from
the wall outlet
3. Contact your distributor.
Plastic bag
Do not let anyone put plastic bags for this product on his head or in his mouth. Otherwise, there is a risk of asphyxia. Families with young children should pay special attention to it.
Keep a distance from the produc and the bracket
Climbing the bracket is dangerous of overturning or damage. Families with young children should pay special attention to it.
Put
Avoid placing the product on an uneven suntect or ony other unstable plect. Otherwise, it will cause the product to fall down, which will lead to the risk of injury.
Product Mobility
Before moving this product, you must unplug the power cord plug from the wal outlet and pull out all other cables and connecting wires. Otherwise, it will lead to damage or power or connection wires resulting in fire and electric shock.
clean
Before cleaning this product, you must unplug the power cord plug from the wal outlet, otherwise there is a risk of fire and electric shock.
Jack
The socket of this product can only be connected to the designated equipment and devices. Connecting non-designated equipment or devices is dangerous of causing fire and electric shock.
Location selection
It should be avoided to place the product in the following places, otherwise there is a risk of fire and electric shock.
- High temperature or dusty places.
- Kitchen or other places with lampblack.
- Where the product is exposed to direct sunlight, or any other place where the product will produce high temperature.
Volume
Don’t play music long and loud. Pay special attention when using headphones Excessive volume can damage your hearing
Heavy
Do not place heavy objects on this product Otherwise, the top of the product will be overweight, causing the product to overturn or drop objects on it, which will lead to the risk of injury.
Correct assembly of scaffolds
The incorrect assembly of the bracket may overturn, causing the product to fall off and posing a risk of injury to personnel. Therefore, it must be assembled according to the instructions in the attached installation guide to ensure that the product is properly mounted on its bracket.
WARRANTY
Warranty rules
- Faults arising from normal use of this product can be guaranteed free of charge for from the date of purchase.
- Failure occurs during the warranty period. This warranty card and shopping ticket must be
- In the following cases, no tree warranty will be provided:
- Damage caused by improper use by users.
- Fault damage is caused by irresistible factors such as fire, flood, earthquake and lightning strike.
- Failure caused by unauthorized self-disassemble
- After exceeding the warranty period, the company is responsible for maintenance, but it needs to charge a cost fee.
Maintenance record
Documents / Resources
|
AODSK AED-403 Multifunctional Electronic
Drum
[pdf] User Manual
AED-403, AED-403 Multifunctional Electronic Drum, Multifunctional Electronic
Drum, Electronic Drum, Drum
---|---