CONNECTS2 GRKHD01 Honda Civic 6.8 Inch Grundig Double DIN Stereo Kit Instruction Manual

CONNECTS2 GRKHD01 Honda Civic 6.8 Inch Grundig Double DIN Stereo Kit

The information provided in this document is subject to change without notice due to changes and/or improvements to the product/s.
www.topvehicletech.com

ABOUT THIS PRODUCT

The GRKHD01 installation kit allows for the retention of the vehicle’s steering wheel controls and helps maintain the original aesthetic of the interior when installing a new car stereo. The GRKHD01 gives you everything you need for a complete install in one box. The components of this kit are compatible for the Honda Civic
(Hatchback, 2006-2011) with basic, non-nav factory stereos. The wiring harness and interface will retain the steering wheel controls and original time/date vehicle settings. It features a factory amp turn on wire and also helps retain original climate control button functionality (if vehicle is equipped). The interface supplied features a Honda OEM specific connector.
NB: this installation kit is for Hatchback models which feature a basic, non-navigation stereo as standard.

CONTENTS

• 1x Fascia plate (with accessories)
• 1x Instruction manual
• 1x Steering wheel control harness and interface
• 1x Antenna adapter
• 1x Stereo patch lead

CUSTOMER SUPPORT

Installations should be carried out by, or under the guidance of an experienced installer. If you do encounter any problems during the installation of this product, then please contact our dedicated customer service team at:

• Phone: 01420 470 605 E-
• Mail: help@topvehicletech.com

FITTING GUIDE

STEREO REMOVAL

1. Remove the screws that surround the centre console and pull it up and out, disconnecting the cigarette lighter in the process.
2. Lever the drivers side panel and undo 1x screw inside. When this is done, take a panel removal tool to the steering wheel surround and just clip out of place to allow room for moving the fascia panel.
3. Using the aide of a panel tool again, remove the gear shifter panel, this will allow you access to the 2x screws underneath the head unit that will need to be removed.
4. Unclip the top plastic panel just below the display with a panel removal tool.
5. Removing the top panel will uncover 3x screw atop the fascia panel, these will now need to be removed.
6. Once the screws are out of the way, firmly pull the fascia panel with head unit out of the dashboard and disconnect the wiring in the process.

FASCIA PLATE SET-UP

1. Once you have taken the main fascia panel off, you will need to transfer the air vents to the new fascia. To do this you will need to disengage the clips of each vent as well as a screw on either side. When free, simply re-locate onto the new fascia.
2. Take the old fascia in hand and unscrew the hazard switch housing. When free, re-locate this to the corresponding space on the new fascia.
3. Attach the brackets to either side of the radio. When attached, roughly test fit the radio and bracket combination in relation to the new fascia, doing this, you can best measure whether the brackets need moving forwards/backwards.
4. With the bracketry aligned, go ahead and push the fascia panel into place, connecting the hazard switch in the process. When the “Stereo Installation” process is complete, you can then simply feed the stereo through the fascia’s opening and place the trim in front of the unit.

STEREO INSTALLATION

1. Take the steering wheel control interface and attach the 14-way steering wheel harness connector to the relevant side.

2. Take the patch lead and only attach ‘Key 1’, ‘Key 2’ and ‘Ground’ to the corresponding wires on the stereo. When done, connect the 12-way connector to the steering wheel control interface.

3. Attach the antenna adapter to the vehicles pre-existing connection and the back of new stereo.

4. Attach the 5-pin connector from steering wheel harness to vehicles pre-existing air-con data connector.

5. Attach the 10-pin connector from steering wheel harness to vehicles pre-existing display data connector.

6. Attach the additional wiring on the harness to the back of the stereo:
   Pink – Speed Pulse Blue – Amp Remote Turn On

7. When all the above wires (and any additional accessories) have been connected, finally make the power connections between the stereo and the vehicles pre-existing connector.

STEERING WHEEL CONTROL FUNCTIONALITY

Please note: configuration layout may differ dependent on vehicle model.

SETTING TIME/DATE

1. Press and hold Mode (5.) to enter the clock setting menu.
2. Press Volume +/- (3/4.) to toggle between hour, minute, month and year.
3. To change the value, press Track +/- (1/2.).
4. Once the time & date has been set, press and hold Mode (5.) to exit the clock setting menu.

WIRING DIAGRAM

TECHNICAL ASSISTANCE

• If at any point you experience any problems and need any assistance before, during or after the installation process, please contact us via :

• Phone: 01420 470 605
  E-Mail: help@topvehicletech.com
  Mon – Fri 9am – 5.30pm GMT

• If you would like to download a digital copy of this manual, or any other product, then please visit the www.topvehicletech.com website.

• This manual is considered correct at the time of printing but is subject to change. For the latest manuals & updates, refer to our website.

Copyright 2021 by TopVehicleTech.
All rights reserved. No part of this publication may be reproduced, distributed or transmitted in any form or by any means, including photocopying, recording, copying or other electronic or mechanical methods, without the prior written permission of the author.

References

• Car Technology Solutions | Car Electronics & Parts | Top Vehicle Tech – TopVehicleTech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>