SALTO EM450U00IMB48 XS4 Original+ Door Lock Installation Guide
- June 5, 2024
- SALTO
Table of Contents
SALTO EM450U00IMB48 XS4 Original+ Door Lock
Installation guide
-
Select handing
-
Installation
-
Battery change
WIRELESS with external door detector
Door detector for Ei4xx…
- Entry lock with privacy/ lockout funtion
- Entry lock with privacy/lockout funtion and key override
ELECTRICAL FEATURES
OPERATING CONDITIONS
| Min.| Max.
Temperature (OUTSIDE)| -35ºC| 60ºC
Temperature (INSIDE)| With LR03 Batteries| -5ºC| 50ºC
With FR03 batteries| -35ºC| 60ºC
Humidity| | 0ºC| 95% (Non-Condensing)
SALTO Bulent FEATURES
Frequency Range| 2400-2483.5 MHz
Standard| Bluetooth 5.2 Compliant
Output TX power| +6 dBm
Indoor Range| 10-15m *
- Depending upon installed environment. To ensure correct operation, do not install the device near a metallic surface.
RFID CHARACTERISTICS
Central Frequency| 13,56MHz
PRODUCTS DESCRIPTION
PRODUCT | TECHNOLOGY | SOFTWARE |
---|
COMMERCIAL NAME
| ****
MODEL
| ****
RFID
13.56 MHz
Output max. power
| BLUETOOTH SMART 2400–2483.5
MHz
Output max. power
| IEEE802.15.4 2400–2483.5
MHz
Output max. power
| ****
CONTROL
| ****
READER
| ****
BLE MODULE
| ****
RF2 MODULE
| ****
MOTOR
| SoC
FUS| BLE
Stack
XS4 Original E0102 (A)
| W09| +25 dBm| | | 0037| 0132| | | | |
W0B| +25 dBm| +8 dBm| | 0037| 0132| 0136| | | |
W0J| +25 dBm| +8 dBm| | 0037| 0133| 0136| | | |
W0S| +25 dBm| +2.8 dBm| | 0126| 0132| –| | | |
W09W| +25 dBm| | +5 dBm| 0016/0061/0095| 0132| | 0038/0099| | |
W0BW| +25 dBm| +8 dBm| +5 dBm| 0016/0095| 0132/0140| 0136| 0038/0099| | |
W0JW| +25 dBm| +8 dBm| +5 dBm| 0016| 0133| 0136| 0038| | |
W08| +20 dBm| | | 0037| 0082| | | | |
W08W| +20 dBm| | +5 dBm| 0016/0061| 0082| | 0038| | |
XS4 Original with Keypad E1215 (A)
| W0BK| +25 dBm| +8 dBm| | 0016/0095| 0132| 0136| | | |
W0JK| +25 dBm| +8 dBm| | 0016| 0133| 0136| | | |
W0SK| +25 dBm| +2.8 dBm| | 0126| 0132| –| | | |
W0BWK| +25 dBm| +8 dBm| +5 dBm| 0016/0095| 0132/0140| 0136| 0038/0099| | |
W0JWK| +25 dBm| +8 dBm| +5 dBm| 0016| 0133| 0136| 0038| | |
XS4 Original+ E2131 (A)| W40M| +25 dBm| +6 dBm| | 0174| | | | 0179| 0186|
0187
W60M| +25 dBm| +6 dBm| | 0174| | | | 0179| 0186| 0187
XS4 One+ E2131 (A)| W80M| +25 dBm| +6 dBm| | 0174| | | | 0179| 0186| 0187
W60M| +25 dBm| +6 dBm| | 0174| | | | 0179| 0186| 0187
XS4 Original
i-Button E0127 (B)
| ****
W02
| | | | 0023/0024/
0025
| | | | | |
Hereby, SALTO Systems S.L. (Arkotz Kaela (Pol. Nonbarren), 9 – 20180 Oiartzun– Spain), declares that this access control equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU (RED) and 2011/65/EU (RoHS). You will be able to find a copy of the original declaration of conformity at the following Internet address: https:// www.saltosystems.com/certificate
ELECTRICAL WARNINGS
EN Caution:
- Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion.
- Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
- A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
Distance between this device and human body must be higher than 20 cm.
MECHANICAL WARNINGS
In order to confirm the correct operation of this electronic device, SALTO
recommends using it in combination with a lock destined for that use (door
mass, frequency of use, fire door, etc.) and that is in good operational
conditions. Polished finishes are strongly recommended in seaside environments
for a better performance and durability. The environmental conditions
mentioned in the data sheets are always referred to non-condensation
situations. The Biocote and IA finishes are painted and sharp objects such as
rings or metallic key rings or other metallic objects should be avoided during
any cleaning process. The SALTO product should be treated with care during the
installation process to avoid any aggressive contact that may damage the unit.
It may be necessary to loosen the trims mounting during installation. Do not
bring the device into contact with oil, paints or acids. Do not paint the door
with the mortise lock or electronic device already mounted on the door.
CLEANING THE ELECTRONIC DEVICE: a damp cloth with mild soapy water can be
used. Never use abrasive soaps or sprays. The black chromium finish (“NE”
code) is coated with a protective oil that improves the product conservation.
Its presence may increase the appearance of fingerprint traces after the
needed product handling. Thus, no cleaning processes are applied at the origin
to avoid removing the protective layer. SALTO recommends cleaning the product
surfaces with a damp cloth after its manipulation when the installation is
finished. For best performance, stainless steel should be cleaned regularly.
Note that when the door is closed without the lock having been already
programmed, the lock will automatically lock and can only be opened with a
Portable Programing Device (PPD). If you have questions or doubts on this,
please contact your authorized SALTO supplier.
FCC COMPLIANCE STATEMENT (1)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>