NAVEE NKP2223-B32 Electric Scooter S65 User Manual

NAVEE NKP2223-B32 Electric Scooter S65

Precautions

1. Do not abruptly change the steering direction at high speed.
2. Avoid hitting your head on door frames, elevators, and other overhead obstacles
3. Do not ride in the rain. Avoid wet weather, the braking distance will be extended, please ride carefully.
4. Do not make dangerous actions during riding, such as riding with one leg or one hand. Make sure that both legs and hands are kept on the electric scooter.
5. Unless otherwise authorized by the local laws, it is forbidden and illegal to ride on public roads, motorways, and expressways.
6. In case of uneven roads or other poor road conditions, please slow down in time and ride carefully, slow down or get off the vehicle. Scooter is special riding products. Please try to ride on flat roads without potholes.

Fold/Unfold & Carry

Folding
The scooter MUST be turned off before being folded. Since the product can be folded, for your protection and safety, do not step on or turn the folding system when riding.

1.  Hold the stem, lift the safety lock and open the quick release lever. Lift the safety lock and push down the quick release lever again, then fold the stem.
2.  Align the buckle with the hook and secure them together.

Unfold
Pull the buckle upwards to release it from the hook. Hold up the stem, then lift the safety lock, and push the quick release lever inward to the end.

Carry
Hold thAe stem with either one hand or both hands to carry.Safety Tips: When lifting the stem of the scooter, NEVER put your hands between the joints as may result in serious injuries.

Care & Maintenance

Cleaning
During cleaning, make sure that the scooter’s turned off, the charging cable is unplugged, and the rubber flap is closed. Wipe the main chassis with a soft damp cloth, the hard-to-remove dirt can be scrubbed with a toothbrush. Afterwards, wipe all areas with a dry cloth.

WARNING!

• Do not wash the scooter with a high-pressure water spray.
• Do not clean the scooter with corrosive cleaner, which will damage the external and internal structure of the scooter.

Battery
Always charge before exhausting the battery to prolong the battery’s lifespan. When riding, storing or charging, do not exceed the specified temperature limit (refer to specifications). Failure to follow instructions for use, storage or charging may result in battery damage, failure to charge and void warranty. The fully charged scooter has an approximate standby time of 120-180 days. If it is not used for a long time, it should be charged every 30 days. Please pay attention to the standby time to prevent irreversible damage to the battery caused by not charging.

WARNING!

• Do not use battery packs of other models or brands, as there may be a safety risk.
• Only use the original battery charger to avoid potential damage or fire.
• If the battery is damaged or soaked with water, do not charge or continue to use it.
• Do not remove the battery. Removing the battery is complicated, and improper operation may affect the operation of the scooter.

Storage
If the scooter will not be used for an extended period, fully charge it, then turn it off and store it in a cool, dry place. Recharge the scooter at least every 2 months to prevent battery damage. Make sure the scooter is turned off when being transported and kept in its original packaging if possible.

WARNING!

• Please do not leave the scooter under hot sun or severely humid place for extended periods of time.
• This product contains a built-in lithium battery and must be transported only when permitted by local laws and regulations.

Care & Maintenance

Inflate the Tire
Check the tire pressure every month, and inflate the tires if the pressure is too low. The recommended tire pressure is 45 psi. lf there is a lack of air in the front and rear tires, you may use the extended nozzle supplied with the scooter to inflate tires. First connect the extension nozzle with air pump, then unscrew the front (rear) tire valve cap, and connect the extension nozzle and the valve securely together, then Inflate the tire.
WARNING! Tire removal is very complicated. Please do not remove the tire by yourself. Improper operation may affect the operation of the scooter. Please contact professional support.

Adjust the Disc Brake
Tool: 4 mm hex key (the tool needs to be prepared by the user). Before adjusting, make sure the scooter is turned off and not being charged. During adjusting, pull the end of the brake line to make the line tight.
Note: If the brake is too tight, use the tool to loosen the screw by turning it counterclockwise, pull the disc brake rocker arm outwards, and then tighten the screw. If the brake is too loose, use the tool to loosen the screw by turning it counterclockwise, push the disc brake rocker arm forwards, and then tighten the screw.

WARNING ! As with any mechanical component, a vehicle is subject to high stresses and wear. The various materials and components may react differently to wear or fatigue. If the expected service life for a component has been exceeded, it may break suddenly, therefore risking causing injuries to the user. Cracks, scratches and discoloration in the areas subject to high stresses indicate that the component has exceeded its service life and please contact an authorized or a specialized repairer.

Specifications

1.  Vehicle height: From the ground to the top of the scooter
2.  General range: Measured when there is no wind and at 77 ° F (25 ° C), the scooter is fully charged to ride at a constant speed of 9.3 mph (15 km/h) on a flat surface with a load of 165.3 lbs (75 kg)
3.  To recharge the battery, only use the battery charger provided in the package. Please see battery charger parameters in Specifications.

Trademark and Legal Statement
JVEE is the trademark of Brightway Innovation Intelligent Technology (Suzhou) Co., Ltd .. All rights reserved. Other trademarks mentioned herein may be registered trademarks of their respective owners.

Certification

FCC Supplier’s Declaration of Conformity
This supplier’s declaration of conformity is hereby for

• Product: NAVEE Electric Scooter 565
• Model Number(s): NKP2223-B32
• Brand/Trade: NAVEE
• We declare that the above-mentioned device has been tested and found in compliance with CFR 47 Part Regulation. Responsible Party–U.5.Contact Information Company: Brightway Innovation Intelligent Technology (Suzhou) Co., Ltd.Address: Room 101, Building 6, No. 2B88, Wuzhong Avenue, Yuexi Street, Wuzhong Economic Development Zone, Suzhou Jiangsu P.R. China Country: China

FCC Compliance Statement for USA
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

FCC Note
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Warranty and service

If the product is within the warranty period from the date of your purchase, we will repair, replace or return it free of charge as the case may be if it is confirmed by the manufacturer or dealer that it is faulty or damaged due to quality defects under normal use. Unless otherwise specified by relevant laws, the product or component used for replacement may not be new, but nevertheless performs well and is equivalent, at least, to the original product or component in function. The warranty period is calculated from the first date of purchase of the product, subject to the invoice date. If there is no valid invoice, the warranty period shall be calculated from the date of delivery plus thirty (30) days. If the invoice date is later than the actual delivery date of the product, the warranty period shall be calculated from the actual delivery date. The repaired or replaced products shall continue to enjoy the warranty for the rest of the warranty period, but not less than thirty (30) days. For warranty application, please contact the manufacturer or distributor of the product and follow the instructions. When applying for a warranty, an accurate, complete, and clear valid sales invoice should be provided.
The above warranty does not apply to failure, malfunction or damage caused by: (a) misuse, abuse or improper transportation, maintenance or storage, such as but not limited to use, storage or maintenance under improper temperature, humidity or other improper environmental conditions; (b) force majeure or accidents, network or power interruption and other reasons beyond our reasonable control: (c) repair or removal without authorization from the manufacturer; (d) the way in which damage has been caused by any third party products or services shall be specified ( purposes other than those for which the product has been designated or intended: (f) using the product in violation of the product instructions: (g) using the product for commercial purposes; or (h) the accumulated mileage recorded by the scooter body has exceeded 2000 km. Normal wear and tear or aging, scratches, abrasions and problems caused by the use of coatings, solvents or other chemicals during the general use of the product do not fall within the scope of the warranty. If the original identification label of the product is changed or damaged, this warranty will be invalid. The integrity and completeness of the products and of the attached materials are not within the scope of the warranty .. You should inspect the products on the spot when receiving them and object immediately to any ascertained discrepancy/ ies. The above warranty statement applies to our products. This warranty grants specific legal rights and other rights you may have according to the law. Nothing in this document affects your rights in a fashion that is not susceptible of exclusion or restriction in accordance with the law.If laws in the territory prescribe a longer warranty period, the aforementioned warranty conditions shall be applied in the prolonged warranty period.

Reminder: The following consumables delivered with the scooter upon purchase are not covered by the warranty: inner and outer tires, front lamp assembly, instrument cover, handle cover, fender, rear tail lamp, decorative cover, foot support, charging port seat, rubber plug and scooter kit. When repairing and replacing parts, do not use any replacement parts other than professional parts provided by the original manufacturer. For replacement, please contact the manufacturer.This product is the same as any mechanical parts. The scooter can bear high stress and wear. Various materials and components ( scooter’s machinery, axle) may react differently to wear or fatigue. If the component have reached the expected service life, they may break suddenly, causing the risk of injury. If any problem is found, please repair and replace the parts in time. If there are cracks, scratches and discoloration in the area under high load, it indicates that the component has exceeded its service life. Please contact the manufacturer or dealer to replace the component as soon as possible.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>