milwaukee Redlithium 2000 Lumen Slide Focus Flashlight Instruction Manual
- June 11, 2024
- Milwaukee
Table of Contents
milwaukee Redlithium 2000 Lumen Slide Focus Flashlight
IMPORTANT SAFETY INSTRUCTIONS
– SAVE THESE INSTRUCTIONS –
WARNING
READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
- SAVE THESE INSTRUCTIONS – This manual contains important safety and operating instructions for the REDLITHIUM™ USB battery and USB rechargeable light.
- CAUTION batteries in this USB Use and charge only REDLITHIUM™ USB rechargeable light. Do not use counterfeit, aftermarket, or “knockoff” bat-teries or chargers. Do not wire a battery pack to a power supply plug or car cigarette lighter.
- Before using the battery and light, read the operator’s manual and all labels on the battery and light.
- Use only with Listed/Certified ITE power supply.
- Avoid dangerous environments. Do not charge battery in rain, snow, damp or wet locations. Do not use battery or charger in the presence of explosive atmospheres (gaseous fumes, dust or flammable materials) because sparks may be generated when inserting or removing battery, possibly causing fire.
- Charge in a well-ventilated area. Do not block charger vents. Keep them clear to allow proper ventilation. Do not allow smoking or open flames near a charging battery. Vented gases may explode.
- Maintain charger cord. When unplugging charger, pull plug rather than cord. Never carry charger by its cord. Keep cord from heat, oil and sharp edges. Make sure cord will not be stepped on, tripped over or subjected to damage or stress. Do not use charger with damaged cord or plug. Have a damaged charger replaced immediately.
- Use only recommended attachments.
- Always unplug charger before cleaning or maintenance.
- Do not burn or incinerate batteries. Battery may explode. Toxic fumes and materials are created when battery are burned.
- Do not crush, drop, or damage battery pack. Always securely contain battery packs during transport. Do not use a battery pack that has received a sharp blow, been dropped, run over, or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped on, in a vehicle accident).
- Do not disassemble. If it is damaged, take it to a MILWAUKEE service facility.
- Battery chemicals cause serious burns. Never allow contact with skin, eyes, or mouth. If a damaged battery leaks battery chemicals, use rubber or neoprene gloves to dispose of it. If skin is exposed to battery fluids, wash with soap and water and rinse with vinegar. If eyes are exposed to battery chemicals, immediately flush with water for 20 minutes and seek medical attention. Remove and dispose of contaminated clothing.
- Do not short circuit. A short-circuited battery pack may cause fire, personal injury, and product damage. A battery pack will short-circuit if a metal object makes a connection between the positive and negative contacts on the battery pack. Do not place a battery pack near anything that may cause a short circuit, such as coins, keys or nails in your pocket.
- Do not allow fluids to flow into battery pack. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
- Store in a cool, dry place. Do not store battery where temperatures may exceed 120°F (50°C) such as in direct sunlight, a vehicle, or metal building during the summer.
- To reduce the risk of injury, close supervision is necessary when an appliance is used near children.
- Store idle light out of reach of children. Warm lights can become hazardous in the hands of children.
- Know your light. Read this manual carefully to learn your light’s applications and limitations as well as potential hazards associated with this type of light.
- Maintain labels and nameplates. These carry important information. If unreadable or missing, contact a MILWAUKEE service facility for a free replacement.
SYMBOLOGY
Volts
Amps
Direct Current
Read Operator’s Manual
Do not stare at the operating light source.
Light becomes warm during use. Turn OFF before storing or setting down to avoid heat buildup.
Universal Serial Bus Type-C (USB-C)
Properly Recycle Batteries
European Conformity Mark
Do not dispose together with household waste.
SPECIFICATIONS
- Cat. No. …………………………………………………………… 2162-20
- USB Input Volts …………………………………………………….. 5 DC
- USB Input Amps …………………………………………….. 0.1 – 2.1 A
- Output Volts ………………………………………………………….. 4 DC
- Output Amps …………………………………………………………. 3.5 A
REDLITHIUM™ USB Batteries
- Volts ……………………………………………………………………. 4 DC
Operating Temperature
- Battery and Charger ………..40°F to 104°F (4°C to 40°C)
- Battery and Tool ………..-4°F to 140°F (-20°C to 60°C)
- Cable (USB-C) Cat. No. ………………………. 42-44-1210
BATTERY
WARNING To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., can cause a short circuit.
Maintenance and Storage
Do not expose your battery or cordless tools to water or rain, or allow them
to get wet. This could damage the tool and battery. Do not use oil or solvents
to clean or lubricate your battery. The plastic casing will become brittle and
crack, causing a risk of injury.
Store batteries at room temperature away from moisture. Do not store in damp locations where corrosion of terminals may occur. As with other battery types, permanent capacity loss can result if the pack is stored for long periods of time at high temperatures (over 120°F). MILWAUKEE Li-Ion batteries maintain their charge during storage longer than other battery types. After about a year of storage, charge the battery as normal.
WARNING To reduce the risk of injury or explosion,never burn or incinerate a battery pack even if it is damaged, dead or completely discharged. When burned, toxic fumes and materials are created.
Disposing of MILWAUKEE Li-Ion Battery
- MILWAUKEE Li-Ion batteries are more environmentally friendly than some other types of power tool batteries. Always dispose of your battery according to federal, state and local regulations. Contact a recycling agency in your area for recycling locations.
- Even discharged batteries contain some energy. Before disposing, use electrical tape to cover the terminals to prevent the battery from shorting, which could cause a fire or explosion.
RBRC Battery Recycling Seals
The RBRC™ Battery Recycling Seals (see “Symbology”) on your batteries indicate
that MILWAUKEE has arranged for the recycling of that battery with the
Rechargeable Battery Recycling Corporation (RBRC). At the end of your
battery’s useful life, return the battery to a MILWAUKEE Branch Office/Service
Center or the participating retailer nearest you. For more information, visit
the RBRC website at www.rbrc.org.
LIGHT
WARNING Use and charge only REDLITHIUM™ USB batteries in this USB
rechargeable light. Other types of batteries may cause personal injury and
damage.
Inserting the Battery
- Twist the flashlight head and remove.
- Line up the battery arrow with flashlight arrow, and fully insert the battery.
- Replace the flashlight head and twist to secure.
Charging the Battery
-
Plug your USB cable into a power source such as an AC wall adaptor, computer or car port. Charge rates may vary depending on the power source’s maximum output.
-
To expose the USB port, twist the ring to align the • with the .
NOTE: Always close the USB cover when light is not charging to maintain dust and moisture protection. -
Insert the USB-C plug into the USB-C port.
-
The indicator light will display the charging status:
- Red Pulsing: Charging, 0-49%
- Yellow Pulsing: Charging, 50-99%
- Green Solid: Charging 100%
- Red/Green Flashing: Cold, Wet, Faulty or No Battery
- Red Solid: Over temperature (too hot)
If the indicator light flashes red and green, check that the battery is fully seated into the bay. Remove the battery and reinsert. Batteries outside the normal operating/charging range may not function properly. Allow batteries to warm up/cool down for normal functions to resume. If problems persist, contact a MILWAUKEE service facility.
Operation
CAUTION To reduce the risk of injury, do not stare at the operating light
source.
To avoid damage/discoloration to surfaces due to high temperatures, do not set
the light lens down during use.
Press the power button to turn the light on and off.
Press and hold the power button to cycle through the modes: High, Medium, and
Low. Release the power button when you have reached desired mode. To activate
boost mode, press the power button twice. To deactivate boost mode, press the
power button twice again during the 35 seconds to deactivate boost mode. The
tool will go back to the selected brightness setting. Boost mode not available
at low states of charge. NOTE: The light will default to the selected
brightness setting the next time it is turned on. The indicator light will
display the battery life:
- Red Flashing: 0-3% remaining
- Red Solid: 3-10% remaining
- Yellow Solid: 11-49% remaining
- Green Solid: 50-100% remaining
Extreme Cold: When the battery is < -4°F/-20°C,the LEDs will flash
red/green 3 times before entering sleep mode. When the battery is -4°F/-20°C
to 5°F/-15°C, only low and medium modes are available.
Overheating: If the flashlight starts to dim and the indicator light is
solid red, the battery may be too hot. Normal function will resume when the
battery has cooled.
WARNING To reduce the risk of injury, always unplug the charger and
remove the battery from the charger before performing any maintenance.
The charger and battery have no internal serviceable parts. Never disassemble
the battery or charger.
Maintenance and Storage
Store your charger in a cool, dry place. As a general practice, it is best to
unplug battery chargers and remove batteries when not in use. No battery
damage will occur,however, if the charger and battery are left plugged in.
WARNING To reduce the risk of injury and damage, never immerse your battery or charger in liquid or allow a liquid to flow inside them.
Cleaning
Clean out dust and debris from charger vents and electrical contacts by
blowing with compressed air. Use only mild soap and a damp cloth to clean the
battery and charger, keeping away from all electrical contacts. Certain
cleaning agents and solvents are harmful to plastics and other insulated
parts. Some of these include gasoline,turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia and household detergents
containing ammonia. Never use flammable or combustible solvents around
batteries, charger, or tools.
LIMITED WARRANTY – USA & CANADA
Every MILWAUKEE REDLITHIUM™ USB battery and charger* is warranted to the original purchaser from an authorized MILWAUKEE distributor only to be free from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace repair a REDLITHIUM™ USB battery or charger which, after examination, is determined by MILWAUKEE to be defective in material or workmanship for a period of two (2) years after the date of purchase unless otherwise noted. Return of the REDLITHIUM™ USB battery or charger to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. For the proper shipping procedure of battery packs, contact 1.800.SAWDUST (1.800.729.3878), or go to www.milwaukeetool.com. A copy of the proof of purchase should be included with the return product. This warranty does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.
Normal Wear: This warranty does not cover repair or replacement when normal use has exhausted the life of a part including, but not limited to charging cables, and wall plugs.
This warranty does not cover any cordless product sold with the REDLITHIUM™
USB battery and/or charger. There are separate and distinct warranties
available for these products.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN
IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF
YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO
EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL, OR
PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS
ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY
PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES,WRITTEN
OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED
WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH
DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE
DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES DO
NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU,THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the Find a Service Center Search in the Parts & Service section
of MILWAUKEE’s website www.milwaukeetool.com
or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest MILWAUKEE
factory Service Center location.
2010R MILWAUKEE® Rechargeable 250L Penlight w/ Laser, 2011R MILWAUKEE®
Rechargeable 500L Everyday Carry Flashlight w/ Magnet, and 2012R MILWAUKEE®
Rechargeable Magnetic Headlamp and Task Light.
The Rechargeable Personal Lighting Products referenced above are warranted to
the original purchaser from an authorized MILWAUKEE distributor only to be
free from defects in material and workmanship. Subject to certain exceptions,
MILWAUKEE will repair or replace any part on the above Rechargeable Personal
Lighting Products which, after examination, is determined by MILWAUKEE to be
defective in material or workmanship for a period of two (2) years after the
date of purchase.
All other MILWAUKEE Personal Lighting Products* (see exceptions below) are
warranted to the original purchaser from an authorized MILWAUKEE distributor
only to be free from defects in material and workmanship. Subject to certain
exceptions, MILWAUKEE will repair or replace any part on a personal lighting
product which, after examination, is determined by MILWAUKEE to be defective
in material or workmanship for the lifetime of such personal lighting
products.
Normal Wear: This warranty does not cover repair or replacement when normal
use has exhausted the life of a part including, but not limited to clips,
straps, charging cables, wall plugs, and rubber gaskets. This warranty does
cover the LED in the personal lighting products,subject to the limitations
herein.
This warranty does not cover Cordless Battery Packs or Chargers. There are
separate and distinct warranties available for these products.
Return of all personal lighting products to a MILWAUKEE factory Service Center
location or MILWAUKEE Authorized Service Station, freight prepaid and insured,
is required. A copy of the proof of purchase should be included with the
return product. The above warranties do not apply to damage that MILWAUKEE
determines to be from repairs made or attempted by anyone other than MILWAUKEE
authorized personnel, misuse, alterations, abuse, normal wear and tear, lack
of maintenance, accidents, or caused by alkaline batteries.
SERVICE – UNITED STATES
1-800-SAWDUST (1.800.729.3878)
Monday-Friday, 7:00 AM – 6:30 PM CST or visit
www.milwaukeetool.com
Contact Corporate After Sales Service Technical Support with technical,
service/repair, or warranty questions.
Email:
metproductsupport@milwaukeetool.com
Become a Heavy Duty Club Member at
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE – CANADA
Milwaukee Tool (Canada) Ltd
1.877.948.2360
Monday-Friday, 7:00 AM – 4:30 PM CST or visit
www.milwaukeetool.ca
MILWAUKEE TOOL
13135 West Lisbon Road,Brookfield, WI 53005 USA
References
- Milwaukee® Tool Official Site | Nothing but HEAVY DUTY®
- Milwaukee® Tool Official Site | Nothing but HEAVY DUTY®
- Sitio oficial de Milwaukee® Tool | Nothing but HEAVY DUTY®
- Call2Recycle | Leading the Charge For Battery Recycling
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>