scubapro 4mm Womens Dry Suit User Manual
- June 5, 2024
- SCUBAPRO
Table of Contents
- INTRODUCTION
- DRYSUITS KEY SPECIFICATIONS
- WATERPROOF ZIPPER
- LATEX WRIST & NECK SEALS
- FITTING OF A DRYSUIT
- APPLICATIONS FOR USE
- RISK ASSESSMENT
- TROUBLESHOOTING
- MAINTENANCE, REPAIR & MODIFICATION
- ACCESSORIES
- SAFE DISPOSAL
- PERIOD OF USE
- DESCRIPTION OF PICTOGRAMS
- SIZE CHART
- GENERAL INFORMATION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
DRYSUIT MANUAL
DEEP DOWN YOU WANT THE BEST
SCUBAPRO.COM
SCUBAPRO DRYSUIT MANUAL
Welcome to SCUBAPRO and thank you for purchasing one of our drysuits. This
manual provides you with easy access to the key features and functions of our
SCUBAPRO
drysuits, along with recommendations on how best to service and care for your
suit. Should you wish to know more about SCUBAPRO diving equipment, please
visit our website at www.scubapro.com.
This drysuit manual is published in accordance with the requirements of DIN EN
142252:2017. The products described in this manual are manufactured to the
specifications
prescribed by SCUBAPRO.
INTRODUCTION
Congratulations on the purchase of a high-quality SCUBAPRO drysuit. Whether
you selected our neoprene or Trilaminate model, these products will open a new
world of comfort and security in your diving adventures. Drysuit diving
demands specific techniques and training beyond those required for wetsuit
diving. If you have not dived in a drysuit before, we strongly recommend you
contact a local instructor for education and practice using your new drysuit
under controlled conditions. Both inexperienced and experienced users should
thoroughly read and understand this manual before diving in the drysuit.
If for any reason you have questions that are not covered by this manual or
your instructor, do not hesitate to contact your SCUBAPRO Authorized dealer.
WARNING
SCUBAPRO STRONGLY RECOMMENDS ALL DIVERS UNDERGO TRAINING AND FAMILIARIZATION
WITH A CERTIFIED INSTRUCTOR BEFORE USING THIS PRODUCT.
The following are important safety guidelines every diver should adopt before diving in a drysuit:
-
Follow a complete drysuit diving course with a certified instructor and from an officially recognized approved training agency.
-
Always dive with a buoyancy compensator.
-
Become familiar with all your equipment before diving.
-
Practice drysuit diving skills in safe conditions until confident of your ability.
-
Ensure your buddy is completely familiar with and understands all your drysuit diving systems.
-
Weight should be set to achieve neutral buoyancy with an empty tank. Do not add more weight than this. You should be able to achieve a 5-minute safety stop at 3 meters
(10 feet), neutrally buoyant with a tank containing around 30 bar (500 psi) or less. -
Inspect the zipper, seals, and valves for damage before each dive.
-
Perform regular preventative maintenance on the suit, valves, zipper, and seals.
-
Only allow qualified individuals or Authorized Dealers to perform service on the suit.
-
Understand your personal diving limitations. Do not exceed them.
DRYSUITS KEY SPECIFICATIONS
This manual describes two types of SCUBAPRO drysuit styles, neoprene, and Trilaminate. All suits share several basic features, including the main waterproof zipper, inflation and exhaust valves, low-pressure inflator hose, vulcanized neoprene boots, neoprene hood, and bag. Some models are equipped with a specific repair kit.
2.1 Neoprene
Neoprene suits are constructed of 4mm compressed foam neoprene, laminated with
nylon jersey on both sides. The exterior side is a heavier weave to better
withstand wear and
abrasion, while the inside is designed for comfort. The compressed foam
neoprene is very dense, resisting compression at depth. This means the suit
loses a smaller percentage of its surface buoyancy, requiring less air added
to remain neutral, and also retains more thermal efficiency at depth. Unlike
the Trilaminate, the neoprene has inherent thermal protection and buoyancy
right in the material and generally requires less added insulation worn under
the suit than the Trilaminate, for any given conditions. Every seam receives
an application of three coats of neoprene adhesive. The outside is sewn with a
two-thread locking blind stitch, while the inside is reinforced with a
proprietary liquid polymer that penetrates the interior nylon layer and fuses
to the neoprene itself. This creates a tough and long-lasting waterproof seam.
2.2 Trilaminate
The Trilaminate suits are constructed of three-layer fabric (hence the name
tri-laminate). The suit is first sewn together, then the inside surface of the
seam is treated with waterproof tape. This provides an extremely dry and
reliable construction. The Trilaminate material has neither inherent buoyancy
nor thermal protection, it is only a dry barrier between the diver and the
aquatic environment. This style, known as a “membrane” suit provides a
waterproof shell under which the diver can wear the correct choice of
undergarments suit to the conditions. The suit is more flexible than neoprene
and allows the diver a broader comfort range (especially in warmer
temperatures) than neoprene.
WARNING
NEVER DEPEND ON ANY DRYSUIT AS YOUR SOLE SOURCE OF FLOTATION AND BUOYANCY
CONTROL. ALWAYS DIVE WITH A SUITABLE BUOYANCY CONTROL DEVICE EQUIPPED WITH A
SEPARATE INFLATION SYSTEM.
WATERPROOF ZIPPER
SCUBAPRO drysuits use a waterproof zipper situated horizontally across the shoulders for entry into the drysuit, or diagonal on the front section of the torso. It is positioned so that it closes from left to right. This is because most people are right-handed and will be less likely to damage the zipper or catch clothes or foreign objects in the zipper while closing it. Advise your buddy to place one finger directly in front of the slider as it is closed, helping to guide the undergarment or foreign objects away from the zipper teeth. Also, make sure that your buddy fully tucks in the interior zipper flap before closing the zipper.
WARNING
CLOTHING OR FOREIGN OBJECTS CAUGHT BETWEEN THE ZIPPER TEETH WILL CAUSE THEM TO
SEPARATE, DESTROYING THE WATERPROOF INTEGRITY OF THE ZIPPER. THIS DAMAGE IS
PERMANENT AND IS NOT REPAIRABLE. HAVE YOUR BUDDY EXERCISE CARE WHEN CLOSING
AND OPENING THE ZIPPER.
To close the zipper with the least chance of damage, extend your arms level in
front of you. Advise your buddy to draw the zipper closed from left to right,
keeping one finger in front of the slider to prevent clothing and foreign
object damage to the teeth. Make sure the slider is drawn tight up against the
rubber stop on the right-hand side. If the slider is not tight against the
stop, the zipper will leak.
In the model with a front-diagonal zipper, the closing-opening operation can
be done without the help of your buddy. However, it is suggested to use the
same precautions described for the shoulder-to-shoulder zipper configuration.
3.1 Maintenance of the Zipper
The larger teeth visible on the outside of the zipper are actually just clamps
that secure the smaller teeth visible on the inside surface of the zipper in
place. It is these smaller teeth that interlock and create firm even pressure
on the polymer zipper tape, creating the seal. These teeth, the zipper tape,
and the outer clamps must be kept clean and lubricated to operate properly and
give long product life.
LATEX WRIST & NECK SEALS
Some models of SCUBAPRO drysuits are fitted with flexible latex neck and wrist seals for watertight integrity.
Trimming the Seals to Fit
The latex seals have concentric raised ridges functioning as cutting guides to
assist you in accurately trimming the seals to fit. The seals are slightly
tapered so they get larger when trimmed. Using a sharp pair of scissors, trim
one ring off at a time until the seal is comfortable but still snug on your
neck and wrists. Use care and precision with sharp scissors when trimming
ridges. Leave a smooth surface, as ragged edges can allow tears to form, which
will require the replacement of the seal.
CAUTION
Do not trim too much, or the seals become too loose and may leak. Make sure
you cut the seals cleanly and leave no nicks that can develop into a tear.
WARNING
BLOOD FLOW CAN BE RESTRICTED BY SEALS THAT ARE TOO TIGHT, WHICH CAN ULTIMATELY
LEAD TO INJURY OR DEATH. DO NOT WEAR THE SEALS TOO TIGHT.
4.2 Storage & Maintenance
Store the drysuit so the seals are dry, cool (below 25 degrees C), and out of
direct sunlight. Ultra-Violet light will degrade the latex over time. If the
seals have been exposed to cold temperatures, they will become stiff and lose
their flexibility. This condition is not permanent and can be resolved by a
brief immersion in warm water. Before storing the suit for any length of time,
dust the seals inside and out with pure talc (supplied in the repair kit) as a
preservative. Do not use perfumed cosmetic talc, as it contains oils that can
damage the latex. Do not use oils or lotion on the seals. Avoid contact with
copper.
4.3 Possible Allergy Risk
A small percentage of people have an allergic reaction to natural latex, the
material from which the neck & wrist seals of some models are manufactured.
This allergy can range from mild to severe skin rash and itching. It is the
responsibility of the user to pre-determine if he or she has a Latex allergy,
or to recognize it during use, and discontinue the use of the suit until the
problem can be rectified. This usually means removing the latex seals and
installing new seals made of alternative materials.
4.4 What is Latex Allergy?
Latex allergy is a reaction to certain proteins in latex rubber. The amount of
latex exposure needed to produce sensitization or an allergic reaction is
unknown. Increasing exposure to latex proteins increases the risk of
developing allergic symptoms. In sensitized persons, symptoms usually begin
within minutes of exposure; but they can occur hours later and can be quite
varied. Mild reactions to latex involve skin redness, rash, hives, or itching.
More severe reactions may involve respiratory symptoms such as runny nose,
sneezing, itchy eyes, scratchy throat, and asthma (difficult breathing,
coughing spells, and wheezing). Rarely, shock may occur; however, a life-
threatening reaction is seldom the first sign of latex allergy.
WARNING
DETERMINE IF YOU HAVE A LATEX ALLERGY, AND TO WHAT EXTENT BEFORE PURCHASING OR
USING A DRYSUIT WITH LATEX SEALS.
FITTING OF A DRYSUIT
- First, remove your watch as it could tear wrist seals.
- Drysuits in general and Trilaminate models, in particular, are designed to fit less snugly than neoprene wetsuits. However, a good fit is still required. You should be able to reach both hands over your head and be able to squat on your knees without restriction while wearing the drysuit and the heaviest undergarments you intend to wear.
- The suit should not be tight in the crotch, or too long.
- If the legs are too long, the air volume in the suit can dislodge the boots off your feet.
To ensure a good fit:
- Wear the bulkiest undergarment you are likely to wear under the suit.
- Make sure the suit is not restrictive in any area.
- Make sure you can raise both hands above your head, touch your toes, and squat to your knees without restriction.
- Make sure the crotch (with suspenders properly adjusted) is not more than 10 cm (4 inches) below your crotch.
- Make sure you can easily reach both valves.
NOTE: You will be considerably bulkier in a drysuit than with a wetsuit and the boots are bigger. If you already own a BC, make sure that it will properly fit over the drysuit. Also make sure that your feet in the drysuit boots fit all the way into your fins, or else purchase larger fins. Having fins that are too small to wear properly will result in foot cramps and lost fins, both potentially dangerous situations.
5.1 Donning the drysuit
- First remove all jewelry and watch as it could tear wrist seals.
- Lay the suit out flat and do a quick overall inspection to ensure it is in good order.
- Dust the inside of the latex seals with talc.
- Lubricate the zipper with the wax stick provided in the repair kit.
- Fold the torso of the suit inside out over the legs to about waist level, so the suspenders are exposed.
- Make sure the suspenders are correctly attached and are not tangled or twisted
- Sit down if possible and insert your foot first into the suit, making sure you do not tanglefoot in the suspender.
- Grasp suit material at calf level and gently ease foot into the boot. Pull up on the leg.
- Repeat with another leg.
- Grasp the torso and ease the suit up so that the crotch of the suit is correctly positioned.
- Raise suspenders over the shoulders and adjust them so they support the weight of the suit.
- When present, fold the neoprene outer cuffs back away from the seals.
- Insert the first arm all the way, taking care of the seal when pushing a hand through.
- Repeat with the second arm. Try to make sure the inside zipper flap is not curled under during this process. Make sure that if the drysuit undergarment is equipped with thumb loops, they are fully retracted, and not caught between the seal and your wrist. This will cause a leak.
- Grasp the top edge of the neck seal with both hands, fingers on the inner surface, and thumbs on the outside. Make sure your fingernails do not tear the latex or smooth skin neoprene. Spread the opening wide enough to draw the neck seal over your head, and adjust so it is comfortable. (Note: some divers prefer to don the neck seal first, inserting the arms after. This is a matter of personal preference).
- Have your buddy make sure the drysuit undergarment is correctly positioned under the latex seal so that there will be no cold spots.
- Instruct your buddy to draw the zipper closed from left to right, keeping one finger in front of the slider to prevent clothing and foreign object damage to the teeth. Make sure the slider is drawn tight up against the rubber stop on the right-hand side. If the slider is not tight against the stop, the zipper will leak.
- Attach the low-pressure hose with a quick disconnect fitting to the inflate valve by pulling back on the fitting and inserting it over the valve stem. Depress the side inflate button briefly to ensure the valve is working properly. Air will enter the suit, partially inflating it. Disconnect the low pressure inflate hose.
- To check the proper function of the exhaust valve, turn it to the “OPEN” or “-“ position and crouch to your knees. The suit should deflate and you should hear the air escaping from the valve.
- Hood Pull the hood over your head and position it comfortably. Tuck the neck of the hood under the neoprene neck cuff for a more watertight seal and better insulation.
- Gloves Pull on each glove and fold the neoprene outer cuff over the glove for a more watertight seal and better insulation. If using dry gloves, make sure the instructions for use are respected.
NOTE: Latex is an excellent watertight seal material but has virtually no insulation value. It is important to adjust the neoprene wrist and neck over cuffs properly so that they help insulate the latex seal against the cold water. This feature is an important advantage over drysuits that use unprotected latex seals. The outer cuffs also protect the latex seals from abrasion and UV degradation.
5.2 Doffing the drysuit
To take off the drysuit, follow the same procedures for donning the suit, but
in reverse order.
APPLICATIONS FOR USE
Both the Neoprene and Trilaminate drysuits are made of the finest materials and to extremely high standards of workmanship. However, they must be used within reasonable limits.
WARNING – DO NOT:
– Exceed the maximum depth to which you are currently certified.
– Use the drysuits in toxic or hydrocarbon-rich environments.
– Use the drysuit as a buoyancy lifting device.
– Use the drysuit without a separate buoyancy control device.
– Use inflation gases other than air except for argon.
– Use the suit with any weight harness or other weight system that is not
equipped with a quick-release system.
6.1 Pre-Dive Suit Checks
Before EVERY dive, make sure the suit is in good condition by checking the
following:
– No visible damage to materials or accessories anywhere on the suit.
– Check latex or smooth-skin neoprene seals for small tears or holes
– Verify that inflate and exhaust valves are intact and functioning properly
Check low-pressure hose and fittings are intact, undamaged, and properly
connected. Inspect waterproof zipper for excess wear or any damage.
6.2 Post-Dive Suit Checks
After EVERY dive, complete all the pre-dive checks listed above and inspect
the suit for any possible new damage. Repair any damage immediately, or take
the suit to an Authorized SCUBAPRO dealer for repair.
6.3 Inspection Intervals
In addition to the checks listed above to be performed before every dive, the
Valves should be inspected and serviced by an authorized SCUBAPRO dealer on an
annual basis.
6.4 MOD or Max Operating Depth
The European Norm EN 250 norms restrict the depth to 50 meters for
recreational diving. For technical diving, the MOD is well beyond the
recreational diving limits.
RISK ASSESSMENT
Drysuit diving, like any other aspect of advanced SCUBA diving activity, carries a degree of inherent risk. These include:
7.1 Hyper/hypothermia
Drysuits are often used in extreme temperature conditions, where there may be
combinations of cold surface conditions and cold water, or hot surface
conditions and cold water. It is important to know your own personal thermal
safe range, to avoid overheating, or becoming chilled. While a drysuit and
warm undergarment have excellent thermal protection, they do have limits and
your safe & enjoyable time in the water is variable based on water temperature
and condition, workload, and your own body type. Hypothermia is the cooling of
the body core to unsafe levels. Hyperthermia is the overheating of the body
core to unsafe levels. Hyperthermia in drysuit use is most often experienced
during surface intervals in hot weather, or during periods of excessive
workload in warm, shallow water.
WARNING
LEARN YOUR OWN LIMITATIONS AND LEARN TO RECOGNIZE DISCOMFORT AS A DANGER
SIGNAL. AVOID HYPERTHERMIA & HYPOTHERMIA AS BOTH CAN BE HARMFUL OR FATAL.
MONITOR YOUR WORK RATE DURING ALL DIVING ACTIVITIES TO AVOID EXCESSIVE AIR
CONSUMPTION, FATIGUE, OVERHEATING, AND OTHER SYMPTOMS.
7.2 Change of Buoyancy with Depth
Neoprene
All neoprene products used in scuba diving incorporate closed-cell foam to
provide thermal protection. Under increasing pressure as depth increases,
these bubbles diminish in size, resulting in a loss of buoyancy as the diver
descends.
Note: Learning to compensate for this loss of buoyancy is one of the
vital skills that must be learned in the proper use of a drysuit.
Trilaminate
As the Trilaminate material is a membrane and lacks a closed cellular
structure, the material itself does not change buoyancy with depth. However,
the air trapped within the suit by the thermal undergarment will be compressed
and the diver compensates for this by adding air during descent and venting
air during ascent, to remain neutrally buoyant.
WARNING
BUOYANCY CONTROL IN A DRYSUIT IS MORE COMPLEX THAN IN A WETSUIT AND IS A VITAL
SKILL TO BE LEARNED DURING THE INSTRUCTION IN THE USE OF A DRYSUIT.
7.3 Loss of Thermal Insulation at Depth
Drysuits in general provide thermal insulation by creating an air space
between the diver and the cold water.
Neoprene
In a neoprene suit, the neoprene material becomes thinner under pressure (see
above) and loses not only buoyancy at depth, but also some insulation value.
Divers planning to spend time at greater depths must account for the
diminished thermal protection at depth by wearing added under suit protection.
Trilaminate
As the material is a membrane only, the thermal insulation value of the
material alone is minimal and does not change with depth. However, divers
planning to spend time at greater depths must account for the colder
temperatures normally found there by wearing added under suit protection.
7.4 Fitting the Suit
A proper fit in a drysuit is very important. Too loose a fit will allow such
hazards as too much air moving around in the suit, difficult buoyancy control
and if the legs are too long, the boots can slip off the divers’ feet. Seals
that are too loose will leak. Too tight a fit can result in restriction of
blood flow causing loss of feeling in the extremities, or lack of oxygen to
the brain. Seals that are too tight will also restrict blood flow.
7.5 Inflation Gases
We recommend using air for inflation. Argon can be used by properly trained
divers. Do not use gas mixes with elevated oxygen levels, or with helium (Tri-
Mix, etc.). Helium is an excellent heat conductor, and will significantly
reduce the thermal efficiency of the suit, risking hypothermia.
7.6 Proper Maintenance
A drysuit is a complex piece of equipment designed to keep a diver comfortable
in extreme conditions. Treat is with respect, maintain it properly, and
inspect it for wear and damage BEFORE & AFTER each dive. Failure to take these
precautions may be hazardous.
7.7 Allergies
In addition to the possible allergic reaction to latex used in the neck and
wrist seals, a small percentage of the population is known to experience an
allergic reaction to neoprene. Although this is less of a problem with
drysuits than with wetsuits, as the diver normally wears an undersuit to
separate the drysuit from his or her body, some exposure can still result. Be
sure to determine you are free from neoprene allergy before purchasing any
neoprene product.
TROUBLESHOOTING
NOTE: A properly functioning drysuit is a closed environment and a certain amount of condensation on the inside of the suit is natural. Divers exerting a lot of energy or spending time above the water on a warm day with their suit closed will notice this more.
8.1 Leaks
Zipper
-
The slider is not closed all the way. Have your buddy check for full closure.
-
Zip has failed – inspect for a split in closed teeth.
-
Zipper material failed – can either be punctured or damaged by abrasion.
-
Foreign material caught in teeth – dirt, sand, debris, or the drysuit undergarment is frequently the trouble.
-
If the zipper is old, worn out, or damaged in some other way – have it replaced.
Valves -
The installation has loosened. Check back plate screw for tightness. Neoprene suits can see this, as the neoprene may continue to compress over time. Tighten if needed.
-
The exhaust valve may be improperly adjusted, or there may be debris (sand, hair, etc.) under the seal.
-
Valve parts may need servicing or replacement due to use and wear.
Seals -
Seals leak for two reasons, damage or interference.
-
Check the seals for holes or tears caused by sharp objects, wear & tear, or chemical damage.
-
Check that there are no foreign objects such as hair, or sections of undergarment.
-
Check for over-trimming.
-
Check they are adjusted properly and do not have folds that can create leaking channels, especially around the tendons in the wrists.
Damage to Suit Fabric -
The suit fabric may leak due to wear, abrasion, puncture, or tearing.
-
Avoid sharp and abrasive objects
-
Divers exposed to corrosive chemicals must take extra care cleansing & rinsing the suit after each exposure. Some chemicals can degrade or delaminate the suit materials to
the point of failure.
8.2 Leak Testing Your Suit
Your drysuit can be tested for leaks by plugging the wrist and neck seals with
objects of suitable size, closing the zipper, and using the low-pressure
inflation hose attached to the
inflate valve to inflate the suit. Wrap an elastic band around the seal to
help the plug stay in place under pressure. Start with the adjustable exhaust
valve set at the lowest release
pressure, and gradually increase until the suit is firm, but not hard. This
way you will not stress the seals, fabric or seams of the suit.
WARNING
DO NOT use GLASS objects to plug the neck or wrist seals. Occasionally, the
internal pressure will blow the plug out of the seal. Glass can shatter,
causing injury. Once the suit is inflated, submerge it a section at a time in
the bathtub, and inspect for leaks. Small bubbles will appear if a leak is
present. Alternately, lay the inflated suit down outside,
and slowly pour warm soapy water over the suspected areas. The soap solution
will blow small bubbles, or create fine foam over the leak. Once the leaks are
located, mark the area, rinse and dry the suit thoroughly, and follow the
repair kit instructions. If you prefer, your Authorized SCUBAPRO dealer can
provide this service.
MAINTENANCE, REPAIR & MODIFICATION
It is not within the scope of this basic manual to provide complete and
detailed repair instructions for all the situations that may be found. Basic
maintenance for the suit, the
materials, and individual components such as zipper, seals, valves, etc., may
be found under those individual headings.
! WARNING
UNAUTHORIZED REPAIRS AND /OR MODIFICATIONS TO THE DRYSUIT WILL VOID THE
WARRANTY AND POSSIBLY CAUSE THE SUIT TO FAIL TO PERFORM PROPERLY, RESULTING IN
SERIOUS INJURY OR DEATH. ALWAYS TAKE THE SUITS TO AN AUTHORIZED SCUBAPRO
DEALER FOR THIS WORK.
9.1 Cleaning, Disinfection & Decontamination
After each use:
- Rinse outside of suit with clean fresh water.
- Wipe seals clean with clean fresh water.
- Rinse valves with clean fresh water.
- Hang suit upside down to dry.
If the suit gets wet inside
Clean the inside of the suit with clear fresh water and dry it inside out.
Latex seals
Lightly dust with nonperfumed talc.
Degreasing
If the suit is exposed to oil or grease, clean with a mild grease-cutting
detergent and a soft brush. Rinse with clean fresh water.
DO NOT ALLOW OIL OR GREASE RESIDUE TO REMAIN ON THE SUIT FOR ANY LENGTH OF
TIME – IT MAY DEGRADE THE MATERIAL.
Decontamination
Recreational divers should take care to avoid exposure to contaminated water
and environments. Professional, commercial, rescue, and military divers who
may be forced to dive in contaminated conditions must identify the contaminant
and take appropriate steps to remove the contaminant from the suit before it
can be used again.
9.2 Storage & Transport
Drysuits are best stored on the SCUBAPRO drysuit hanger that hangs the suit
upside down by the feet with the zipper open. Keep in a cool dry place out of
the sun. Keep copper away from the latex seals. Additional advice may be found
in specific sections above. Transport the suit in the nylon bag provided. Try
to clean excessive dirt and sand from the suit before placing it in the bag.
ACCESSORIES
10.1 Hood
The supplied hood has a face seal section lined with super extensible fabric
for flexibility and comfort.
The Diamond Span lining inside will retain the warmth of your head and is also
very quick drying. The air vent system allows trapped air to escape and its
placement prevents outside water from entering. The neck section is designed
to lay over top of the neck seal on the suit for extreme protection.
10.2 Bag
Each SCUBAPRO drysuit is supplied in a carrying bag. The flat design with a
perimeter zipper allows the bag to fold open for use as a dressing mat to keep
your feet clean while getting in and out of the suit. Inside the bag is a
permanently attached pouch where the repair kit, zipper lubricant, and seal
talc are conveniently stored.
10.3 Valves
SCUBAPRO drysuits feature the low profile Si-Tech valve system, the most
tested, reliable and diffused worldwide.
10.4 Hose
The diver must use the original supplied SCUBAPRO super flow low-pressure hose
along with SCUBAPRO quick coupling. In case of hose replacement, it is
compulsory to replace the hose by a standard SCUBAPRO super flow low-pressure
hose.
Inflate Valve Features
- 360 degrees swivel for optimal inflator hose placement.
- Universal low-pressure male quick disconnect.
- Push the button for easier, more comfortable use.
- A low-profile curved back plate reduces bulk and increases comfort.
- Located at the center of the chest.
Exhaust Valve Features
- Deflate pressure fully adjustable with manual override.
- High flow rate.
- Low profile with smooth contours to avoid catching valve when donning BC.
- A low-profile curved back plate reduces bulk and increases comfort.
- Located on the left shoulder.
Low-Pressure inflator hose
- Standard super flow SCUBAPRO low-pressure hose with screw-on QD fitting.
- Hose protector included.
SAFE DISPOSAL
If you need to destroy the drysuit please make sure to follow local regulations and prescriptions.
WARNING
UNAUTHORIZED CHANGES OR DAMAGES RESULTING FROM THE INSTALLATION OF A URINATION
SYSTEM WILL VOID THE WARRANTY.
PERIOD OF USE
The lifespan/duration of use of this product cannot be defined in general.
Various factors such as storage conditions, level of care, frequency of usage
and the field of application will influence the lifespan/duration of use.
Extreme usage conditions can lead to excessive damage that may result in the
product being no longer fit for use.
Factors such as an aggressive environment, sharp edges, extreme temperatures
or exposure to chemicals may damage the product beyond repair. Under the
following circumstances, the product should no longer be used and should be
destroyed:
- Damage to the material or parts essential for safety, e.g., bungees, straps, seams (rips, cuts or other)
- Damage to the plastic and/or metal parts (e.g., the valves and/or the latex or silicone)
- Excessive stress on the material caused by over-stretching or over-loading
- When the product no longer appears to be generally safe and reliable
- When the product no longer meets the technical standards (e.g., changes in legal provisions, safety guidelines, technical requirements, or incompatibility with other products)
- When the product’s history and previous use is not known
- When the labeling of the product no longer exists or can no longer be read.
NOTE: Also observe sections 8.1 and 8.2 on damage or faults.
If the drysuit does not pass the regular visual inspection by either the owner
or a specialist the drysuit should be destroyed. Destroying the drysuit (i.e.,
by cutting it) is essential to ensure that the drysuit cannot be reused. The
product must be serviced annually by an authorized dealer. The decision will
be made by the responsible person at the mandatory yearly service
DESCRIPTION OF PICTOGRAMS
SIZE CHART
You will find the size chart on the last page of this manual.
GENERAL INFORMATION
15.1 Authorized Representative
SCUBAPRO
ASIA PACIFIC
608 Block B, MP Industrial Center
18Ka Yip Street, Chaiwan
HONG KONG| SCUBAPRO
USA & LATIN AMERICA
1166 Fesler Street
EI Cajon, CA 92020
USA| JOHNSON OUTDOORS
GERMANY
Bremer Straube 4
90451 Nürnberg
GERMANY
---|---|---
SCUBAPRO
AUSTRALIA
Unit 21/380 Eastern Valley
Way Chatswood, NSW 2067
AUSTRALIA| SCUBAPRO
S.A.S FRANCE
Les Terriers Nord
175, Allee Bellevue
06600 Antibes
FRANCE
---|---
15.2 European notified body
The PPE covered by this instruction manual has been type tested and certified
in accordance with EU Regulation 2016/425 and in compliance with the standard
EN14225-2:2017 by:
TRILAME DRY SUITS :
BG Bau
Fachbereich Persönliche Schutzausrüstungen Prüf- und
Zertifizierungsstelle des FB „PSA“
Identification no. 0299:
Zwengenberger Straße 68
42781 Haan
Phone: 0800 6686688-38050
Fax: 02129 576-0
Web: www.zs-bgbau.de
NEOPRENE DRY SUITS:
RINA
Notified Body No 0474
Via Corsica 12,
16128 Genova
Italy
Phone: +39 0105385341
Fax: +39 0105351000
Web: http://www.rina.org/en
15.3 Source of Standard
Diving drysuits (Neoprene and Trilaminate): EN 14225-2:2017 and EN
14225-2:2018
15.4 Source of Requirement
www.europa.eu
15.5 For Declaration of Conformity
www.scubapro.com
15.6 Warranty
SCUBAPRO warrants to the original consumer purchaser that, for the period of two years from the date of purchase, each SCUBAPRO product component not otherwise warranted and each SCUBAPRO replacement part purchased from an authorized SCUBAPRO dealer, will be free from defects in materials and workmanship under normal use and with reasonable maintenance. This warranty does not apply to any product or part used commercially. A list of Authorized SCUBAPRO Dealers can be obtained online at scubapro.com. SCUBAPRO will, at its option, repair or replace without charge any warranted component or replacement part that is defective in materials or workmanship. Repair or replacement is SCUBAPRO’s only responsibility and your only remedy under this warranty. To obtain warranty services, you must deliver the affected component or part, together with your Original Owner Identification Card (for a component) or other proof of purchase to any authorized SCUBAPRO dealer, or directly to SCUBAPRO at 1166-A Fesler Street, El Cajon, CA 92020, or to any other SCUBAPRO factory in the United States, Europe, or Asia. If you send the component or part to a SCUBAPRO factory, you must pay the shipping charges to the factory. This warranty does not cover damage resulting from improper usage, improper maintenance, neglect of care or maintenance or repair service performed by someone other than an Authorized SCUBAPRO Dealer.
ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE
DURATION OF THIS WRITTEN WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you.
SCUBAPRO SHALL NOT BE LIABLE FOR LOSS OF USE OR ANY OTHER INCIDENTAL,
CONSEQUENTIAL, OR INDIRECT COSTS, EXPENSES OR DAMAGES.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above exclusions may not apply to you. If
additional details are required regarding your warranty, please contact your
nearest Authorized SCUBAPRO Dealer or SCUBAPRO directly.
WARNING
DO NOT REMOVE THE STITCHED LABELS. LABELS SHOW MANDATORY INFORMATION ABOUT THE
PRODUCT AND PRODUCTION DATES. PROOF OF PURCHASING DATE OR PRODUCTION DATE WILL
BE NEEDED IN CASE OF A WARRANTY CLAIM.
RECOMMEND SIZE CHART
Recommended
drysuit size chart| Size key| HEIGHT
(in/cm)| WEIGHT
(lbs/kg)| SIZE NOTE: These charts are intended to act as a sizing guide.
We recommend that all suits be tried on to ensure a perfect fit. Please allow
for undergarments in your
measurements. We recommend if you are
between sizes to choose the larger size. Not
all sizes are available in all models
---|---|---|---|---
MEN
WEIGHT (lbs/kg)
HEIGHT (in/cm)/| 130-155 lbs
60-70 kg| 145-165 lbs
65-75 kg| 155-175 lbs
70-80 kg| 165-185 lbs
75-85 kg| 175-200 lbs
80-90 kg| 185-210 lbs
85-95 kg| 200-220 lbs
90-100 kg| 210-230 lbs
95-105 kg| 220-245 lbs
100-110 kg| 230-255 lbs
105-115 kg
---|---|---|---|---|---|---|---|---|---|---
5’3” – 5’5”
160 cm – 165 cm| 2XS/44| | | | | | | | |
5’5” – 5’7”
165 cm – 170 cm| | XS/46| | | | | | |
5’7” – 5’9”
170 cm – 175 cm| | | S/48| MS/25| | | | |
5’9” – 5’11”
175 cm – 180 cm| | | ST/94| M/50| LS/26| | | |
5’11” – 6’1”
180 cm – 185 cm| | | | MT/98| L/52| XLS/27| | |
6’1” – 6’3”
185 cm – 190 cm| | | | | LT/102| XU54| 2XLS/28| |
6’3” – 6’5”
190 cm – 195 cm| | | | | | XLT/106| 2XU56| 3XLS/29|
6’5” +
195 cm +| | | | | | | 2XLT/110| 3XU58| 4XU60| 5XU62
USA/INT/EU
SIZE KEY| • 2XS/44 =
2 Extra Small
• XS/46 =
Extra Small
• S/48 = Small
• ST/94 =
Small Tall| • MS/25 =
Medium Short
• M/50 =
Medium
• MT/98 =
Medium Tall| • LS/26 =
Large Short
• L/52 = Large
• LT/102 =
Large Tall| • XLS/27 =
Extra Large
Short
• XL/54 =
Extra Large
• XLT/106 =
Extra Large Tall| • 2XLS/28 =
2 Extra Large
Short
• 2XL/56 =
2 Extra Large
• 2XLT/110 =
2 Extra Large Tall| • 3XLS/29 =
3 Extra Large
Short
• 3XL/58 =
3 Extra Large| • 4XL/60 =
4 Extra Large
• 5XL/62 =
5 Extra Large
---|---|---|---|---|---|---|---
WOMEN
WEIGHT (lbs/kg)
HEIGHT (in/cm)/| 90-120 lbs
40-55 kg| 100-130 lbs
45-60 kg| 110-145 lbs
50-65 kg| 120-155 lbs
55-70 kg| 130-165 lbs
60-75 kg| 145-175 lbs
65-80 kg| 155-185 lbs
70-85 kg| 175 lbs +
80 kg +| ***|
---|---|---|---|---|---|---|---|---|---|---
4’11” – 5’1”
150 cm – 155 cm| 2XS/34/0| | | | | | | | |
5’1” – 5’3”
155 cm – 160 cm| | XS/36/2| | | | | | |
5’3” – 5’5”
160 cm – 165 cm| | | S/38/4| MS/20/6S| | | | |
5’5” – 5’7”
165 cm – 170 cm| | | ST/76/4T| M/40/6| LS/21/8S| | | |
5’7” – 5’9”
170 cm – 175 cm| | | | MT/80/6T| L/42/8| XLS/22/10S| | |
5’9” – 5’11”
175 cm – 180 cm| | | | | LT/84/8T| XL/44/10| 2XLS/23/12S| |
5’11” – 6’1”
180 cm – 185 cm| | | | | | XLT/88/10L| 2XL/46/12| |
6’1” +
185 cm +| | | | | | | 2XLT/92/12T| 3XL/48/14| 3XLT/96/14T| 4XL/50/16*
USA/INT/EU
SIZE KEY| • 2XS/34/0 =
2 Extra Small
• XS/36/2 =
Extra Small
• S/38/4 = Small
• ST/76/4T =
Small Tall| • MS/20/6S =
Medium Short
• M/40/6 =
Medium
• MT/80/6T =
Medium Tall| • LS/21/8S =
Large Short
• L/42/8 = Large
• LT/84/8T =
Large Tall| • XLS/22/10S =
Extra Large
Short
• XL/44/10 =
Extra Large
• XLT/88/10L =
Extra Large Tall| • 2XLS/23/12S =
2 Extra Large
Short
• 2XL/46/12 =
2 Extra Large
• 2XLT/92/12T =
2 Extra Large Tall| • 3XL/48/14 =
3 Extra Large
Short
• 3XLT/96/14T =
3 Extra Large| • 4XL/50/16
4 Extra Large
---|---|---|---|---|---|---|---
References
- scubapro.com
- scubapro.com
- Prüfung und Zertifizierung | BG BAU - Berufsgenossenschaft der Bauwirtschaft
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>