VONROC LL503DC Cross Line Laser User Manual

CROSS LINE LASER
LL503DC / LL504DC

Original Instructions

LL503DC Cross Line Laser

SAFETY INSTRUCTIONS

Read the enclosed safety warnings, the additional safety warnings and the instructions. Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury.
Save the safety warnings and the instructions for future reference.
The following symbols are used in the user manual or on the product:

Read the user manual.
 Denotes risk of personal injury, loss of life or damage to the tool in case of nonobservance of the instructions in this manual.
Do not use in rain.
Indoor use only.
Do not dispose of the product in unsuitable containers.
**** The product is in accordance with the applicable safety standards in the European directives.
Risk of eye injury due to laser beams! Never look directly into the laser and do not direct the laser beam towards reflecting surfaces!

GENERAL SAFETY WARNINGS

• To operate this device safely, the user must have read and understood these instructions for use before using the device for the first time.
• Observe all safety instructions! Failure to do so may cause harm to you and others.
• Retain all instructions for use, and safety instructions for future reference.
• If you sell or pass the device on, you must also hand over these operating instructions.
• The device must only be used when it functions properly. If the product or part of the product is defective, it must be taken out of operation and disposed of correctly.
• Never use the device in a room where there is a danger of explosion or in the vicinity of flammable liquids or gases.
• Keep children away from the device! Keep the device out of the way of children and other unauthorized persons.

SPECIFIC SAFETY WARNINGS

• The device is intended for using in dry environment.
• Avoid the influence of humidity and dirt as well as direct sun rays.
• Do not operate the device in the proximity of welding machines, induction heaters and other electromagnetic fields.
• Do not expose the device to high temperatures for a longer period of time.
• Symbols appearing on your device may not be removed or covered. Signs on the device that are no longer legible must be replaced immediately.

SAFETY WARNINGS FOR BATTERY
a) Do not open the battery. Danger of shortcircuiting.
b) Protect the battery against heat, e. g., against continuous intense sunlight, fire, water, and moisture. Danger of explosion.
c) In case of damage and improper use of the battery, vapours may be emitted. Ventilate the area and seek medical help in case of complaints. The vapours can irritate the respiratory system.
d) Use the battery only in conjunction with your Vonroc product. This measure alone protects the battery against dangerous overload.
e) The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit can occur and the battery can burn, smoke, explode or overheat.

Handling of laser beams

• Do not look directly into the beam, not even from great distances.
• Never direct the measuring beam towards people, other living creatures or reflecting surfaces.
• Conventional laser glasses do not protect against the dangers of laser beams. They only serve for improved recognition of the laser beam.

MACHINE INFORMATION

Intended use
The cross line laser is intended for determining and checking horizontal and vertical lines onto the wall and is therefore designed for aligning objects such as tiles or pictures. The cross line laser is suitable for indoor use.
TECHNICAL SPECIFICATIONS

(Lithium battery)

Battery charging time| 2.5 hours
Weight (without universal clamp)| 213 g
Dimensions (without universal clamp)| 65x60x75 mm

• The working range may be reduced by unfavourable environmental conditions (e.g. direct sunlight).
  DESCRIPTION
  The numbers in the text refer to the diagrams on page 2-4.

  1. On / off button
  2. Lock switch
  3. Laser beam outlet
  4. ¼ inch tripod connection
  5. LED indicator
  6. Universal clamp
  7. Clamping jaws
  8. Locking knob (for clamping jaws)
  9. Adjusting knob (for ball joints)
  10. USB type-C plug*
  11. USB cable*
  12. USB type-A plug*
  13. USB type-C connector*

• USB Type-C® and USB-C® are trademarks of USB Implementers Forum.

ASSEMBLY

Using the universal clamp (Fig. B)

1. Screw the universal clamp (6) into the tripod connection (4) at the device.
2. Loosen the locking knob (8) and push the clamping jaws (7) apart until they fit onto the carrier.
3. Tighten the locking knob (8) until the jaws of the universal clamp (6) are firmly attached to the carrier and the mount can no longer be moved.
4. Loosen the adjusting knob (9).
5. Swivel the device to the desired position.
6. Retighten the adjustment knob (9).
7. To unfasten the clamping jaws, loosen the  universal clamp (6) until the can be removed from the carrier without difficulty.

Using the tripod (not included)

1.  Place the device with the 1/4″ tripod connection (4) on the thread of the tripod or a conventional camera tripod.
2. Roughly align the tripod before switching on the device.

OPERATION

Only the centre of the laser line must be used for marking. The width of the laser line changes depending on the distance.
It’s recommended to carry out an accuracy check before first use and periodic checks during future use, especially for precise layouts. Also when the laser may have been dropped.
** Danger of injury due to defective components! The product must only be put into operation if no defects are found.
Ensure that any defective parts are replaced before the product is used again.
WARNING! Risk of injury due to laser beam!** Never direct the laser beam towards people, other living creatures or reflecting surfaces.

Charging the device (Fig. C)
**** The device must be charged before first use.

1. Plug the USB type-C plug (10) into the USB type-C connector (13) on the device.
2. Plug the USB type-A plug (12) into an power adapter (not included) or device (e.g. computerpowerbank) with suitable female USB connector. Please note that the device should be able to deliver constant 5V 2A power.

3. The Battery LED indicator (5) will lighten up and show the charging status.
   LED Charger status

   Red| Battery charging in progress
   Green| Charging finished, battery fully charged

4. After the battery is fully charged remove the USB type-C plug (10) from the USB type-C connector (13).

It is also possible if the battery is empty to power the device with the charger or with a power bank. Follow the steps as above.
When the device is not being used over a longer period of time it is best to store the battery in charged condition.

Check the device:

• Make sure all parts are fitted on the machine firmly.
• Check whether there are any visible defects: broken parts, cracks, etc.
• Check the accuracy when it is the first time you are using the laser or when the laser has not been checked for accuracy in a while.
• Also check the accuracy when the laser may have been dropped.:
• Make sure all parts are fitted on the machine firmly.
• Check whether there are any visible defects: broken parts, cracks, etc.
• Check the accuracy when it is the first time you are using the laser or when the laser has not been checked for accuracy in a while.
• Also check the accuracy when the laser may have been dropped.

Self- levelling mode (Fig. A, D1)
The lasers are aligned automatically by the pendulum so that the vertical and horizontal lines are displayed level on the wall.

1. Place the laser on a flat surface or fit it to the universal clamp (7) or tripod (not included) and fasten it as described above.
2. Slide the lock switch (2) to the right. Press the ON / OFF button (1) on the device to power on. If the laser flashes, the permissible inclination range of 5 degrees is exceeded. Position the device horizontally until the laser stops flashing.
3. To switch off, slide the lock switch (2) to the left and press the ON / OFF button (1). The laser switches off and the pendulum will be locked.

**** Slide the lock switch (2) to the left when transporting it. This locks the pendulum unit, as it can otherwise be damaged.

Manual mode (Fig. A, D2)
The laser can be aligned manually to the angle you require, to enable for example a diagonal line to be displayed.

1. Place the laser on a flat surface or fit it to the universal clamp (7) or tripod (not included) and fasten it as described above.
2. Check if the lock switch (2) is set to the left. If not, slide the lock switch (2) to the left.
3. Press the ON / OFF button (1) to switch the laser on.
4. Now you can tilt the laser to the angle you require, so that the lines are displayed diagonally on the wall as shown in Fig. D2.
5. To switch off , press the ON / OFF button (1).

MAINTENANCE

Accuracy check
**** Only the centre of the laser line must be used for marking. The width of the laser line changes depending on the distance.

Quick horizontal line check (Fig. A, E1)

1.  Set the device at approximately 5 meters from the wall.

2. Slide the lock switch (2) to the right. Press the ON / OFF button (1) on the device to power on.
   If the laser flashes, the permissible inclination range of 5 degrees is exceeded. Position the device horizontally until the laser stops flashing.

3. After it self-levels, make a horizontal mark on the wall as shown in figure E1. Label this as point A.
   4. Turn the laser 2.5 m to the right.

4. Turn the laser on, and after it self-levels, make a horizontal mark on the wall. Label this as point B as shown in figure E1. When points A and B are more than 2.5mm apart from a vertical perspective, a calibration check is necessary.

Quick vertical line check (Fig. A, E2)

1. Set the device at approximately 5 meters from the wall.

2. Hang a 2.5 meter rope on the wall with a weighon the end of the rope as shown in figure E2.
   The rope must be able to swing freely.

3. Slide the lock switch (2) to the right. Press the ON / OFF button (1) on the device to power on. Position the vertical line next to the wire. If the laser flashes, the permissible inclination range of 5 degrees is exceeded. Position the device horizontally until the laser stops flashing. After it self-levels, the difference must not exceed ± 2.5 mm. When it’s more than 2.5mm apart, a calibration check is necessary.

Calibration check (Fig. A, F)
The accuracy of the horizontal beam can be checked by following these steps:

1. Set the device on a tripod, centered in a room with walls ideally 5 meter away.

2. Slide the lock switch (2) to the right. Press the ON / OFF button (1) on the device to power on.
   If the laser flashes, the permissible inclination range of 5 degrees is exceeded. Position the device horizontally until the laser stops flashing.

3. After it self-levels, make a horizontal mark on the wall anywhere along the horizontal line to indicate the height of the beam. Label this as point A as shown in Fig. F1.

4. Turn the device 180°, and after it self-levels, mark point B as shown in Fig. F2.

5. Turn the device 180°. Position the device as near as possible to the wall at the height of point A as shown in Fig. F3.

6. Turn the device 180°, and after it self-levels, mark point C. This mark should either be directly above, below or on top of point B as shown in Fig. F4. The difference between points B and C is the tolerance. When B and C are more than 0.5 mm/ m apart, an adjustment is necessary. Contact your authorized dealer or else the Vonroc Service Department.

Cleaning
NOTICE! Risk of product damage! Never submerge device in water while cleaning.
Do not use cleaning agents or solvents. Wipe the device using a dry cloth.
Storage
NOTICE! Risk of product damage! Always handle measuring instruments with care.

• Store the product in a dry, well-ventilated place.
• Only store and transport the product in its original packaging.
• Prevent large temperature fluctuations: Always temper the product for a while before use in extremely cold or hot environments.

NOTICE! Risk of product damage! Old, leaky batteries can damage the product. Check the battery regularly.

ENVIRONMENT

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

DECLARATION OF CONFORMITY
LL503DC / LL504DC – CROSS LINE LASER

**** We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European parliament and of the council of 8 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations:

EN 60825-1, EN 61326-1, 2011/65/EU, 2014/30/EU

VONROC • Lingenstraat 6 • 8028 PM Zwolle • The Netherlands

©2022 VONROC
WWW.VONROC.COM
2210-04

References

• VONROC Gereedschap & Tuin artikelen

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>