SCUBAPRO 06.205.519 Pressure Gauge User Manual
- June 3, 2024
- SCUBAPRO
Table of Contents
SCUBAPRO 06.205.519 Pressure Gauge
WARNING
IMPROPER USE OR MISUSE OF THESE INSTRUMENTS, OR ANY DIVING EQUIPMENT, COULD RESULT IN SERIOUS INJURY OR DEATH.
-
Do not use these instruments until you have carefully read this manual. To safely use these products, the user must have successfully completed a course of training in SCUBA diving.
-
Retain this manual for your reference and review it periodically and prior to diving.
-
The dive instrument is a personal protective equipment in compliance with the essential safety requirements of the EU Regulation 2016/425. RINA SpA,Via Corsica 12, I-16128 Genoa, Italy notified body no. 0474, has certified its conformity with the European Standard EN 250:2014. The full text of the EU declaration of conformity is available at
www.scubapro.com/scubapro-declarations-conformity -
The dive instrument is also compliant with the European Union directive 2014/30/EU.
Standard EN 13319:2000
- The dive instrument is compliant with the European standard EN 13319:2000.
PRESSURE GAUGES – EN 250 / bar – psi
On the first stage of the regulator (not pressurized) remove one high pressure port plug; check that the thread is the same as the high pressure hose fitting (7/16” UNF). If not, you can get a thread adaptor from your dive store. Make sure that the o-ring and o-ring groove are clean. Screw the high pressure hose or the adapter into the high pressure port of the first stage regulator, first by hand and then with a wrench. Do not over torque.
ATTENTION
Do not exceed depth, pressure and temperature limits listed on table 1. Take
particular care in carrying and during transport: this is a precision
instrument and must be protected.
CAUTION
- Turn the gauge away from you while opening the tank valve.
- Do not look at gauge face when opening the tank valve.
- Do not bend the high pressure hose.
- Do not pull the tank/regulator assembly by the hose.
WARNING
FAILURE TO FOLLOW THESE CAUTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
DEPTH GAUGE – EN13319/meters – feet
Do not exceed the operational limits (depth, temperature) listed on Table 1 and always use the SCUBAPRO depth gauge with a shock absorber. Take particular care in carrying and during transport: this is a precision instrument and must be protected.
MAINTENANCE for SCUBAPRO PRODUCTS
Rinse thoroughly in fresh water after each dive. especially after diving in
chlorinated water. Let the instruments dry in a cool place away from direct
sunlight. Do not use any kind of solvent, especially alcohol or solvents with
alcohol base, or cleaning liquids. Check the high pressure hose surface for
cuts, holes and abrasions.
If necessary, replace the high pressure hose with original SCUBAPRO service
parts. Check the dial readings with a Laboratory Gauge at least once a year,
or more frequently if you dive very often or if the gauge received hard hits.
The overpressure relief valve on the back of the pressure gauge must be
inspected for functionality once a year and replaced by an Authorised SCUBAPRO
dealer if necessary. Failure to inspect and maintain the overpressure relief
valve could lead to serious injury or death.
SPECIFICATIONS
| TECHNICAL SPECIFICATIONS | DEPTH GAUGE | PRESSURE GAUGE |
|---|---|---|
| Max. operating depth | 60 m/200 ft | 80m/260ft (plastic) 150m/492ft (metal) |
| Max. SCUBA | 40 m/130 ft | 40 m/130 ft |
| End of scale of pressure Max. working pressure | NA NA | 400 bar/6000 psi |
300 bar/4350 psi
Usable on surface| NA| Yes
Tolerances| 3 m, 6 m: + 0,8/- 0,4 m
10 ft, 20 ft: + 3 ft/-1 ft
9 m: + 0,8/- 0,8 m
30 ft: + 3 ft/-3 ft
15 m, 30 m: + 1,0/- 1,2 m
40 ft, 100 ft: + 3 ft/-4 ft
45 m, 60 m: + 1,0/ -1,5 m
145 ft, 200 ft: + 3 ft/-5 ft
| 50 bar: ± 5 bar
750 psi: ± 75 psi
100 bar, 200 bar: ±10 bar
1500 psi, 3000 psi: ±150 psi
300 bar: ±15 bar
4350 psi: ±225 psi
Overpressure burst pressure safety system| NA| < 3 bar/< 44 psi
Safety overpressure flow| NA| > 300 l/min
HP hose – burst pressure| NA| >1250bar / >18.000psi (standard hose)
1600bar / >23.200psi (double reinforced)
HP hose – pull resistance| NA| > 1500 N/> 330 Ibs
HP hose – overall length| NA| 875mm/34.5” (standard length);
custom lengths available
Max. depth indicator| Yes|
External diameter
Thickness
Capsule dimensions
Weight
| Compact: 50mm / 1.96”
Standard: 55mm / 2.15”
| Compact: 50mm / 1.96”
Standard: 60mm / 2.35”
Compact: 26mm / 1.02”
Standard: 27.5mm / 1.08”
| Compact: 21.3mm / 0.83”
Standard: 26.8mm / 1.05”
Compact: 47g / 0.103 lbs
Standard: 55g / 0.120 lbs
| Compact (Plastic): 60g / 0.132 lbs Compact (Metal): 125g / 0.276 lbs
Standard: 81g / 0.178 lbs
Temperature limits| -10°C tot 60°C
14°F tot 140°F
| -10°C tot 60°C
14°F tot 140°F
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>