AL-KO DIVE 5500-3 Drainage Water Pump Instructions

DIVE 5500-3 / DIVE 6300-4

PRODUCT DESCRIPTION

This document describes various different models of immersion pumps. Identify your model using the identification plate.
Product overview

The function of the pump
The submersible pump sucks the liquid to be pumped into the pump through the inlet strainer (8) and pumps it out at the outlet.
Designated use
The submersible pump is designed for home use in your house or garden. Please observe the technical data given in the instructions before putting the pump into operation.

ABOUT THIS HANDBOOK

• Read this documentation before starting up the machine. This is a precondition for safe working and flawless operation.
• Observe the safety warnings in this documentation and on the product.
• This documentation is a permanent integral part of the product described and must be passed on to the new owner if the product is sold.

Explanation of symbols
CAUTION!
Following these safety warnings carefully can prevent personal injury and/or material damage.

Special instructions for greater ease of understanding and improved handling.

Your submersible pump has been designed for use in the following applications:

• emptying containers or pumping liquid from one container into another,

• pumping water from wells, cisterns, and other water tanks

• operating irrigation systems and lawn sprinklers

• for the domestic water supply.
  The submersible pump is designed to pump only the following liquids:

• clearwater

• rainwater

• chlorinated water (pool water)

• water for domestic use.

Possible misuse

Your submersible pump is not intended for permanent operation. The pump may not be used to pump the following liquids:

• drinking water
• saltwater
• beverages or liquid foods
• corrosives or chemicals
• acids or combustible, explosive or gas-forming
• liquids with a temperature above 35 °C
• sandy water or water containing abrasives
• wastewater containing textile or paper particles

Scope of delivery

Thermal protection
Your submersible pump is equipped with a thermal protection switch that automatically switches off the pump in case of overheating. The pump will remain off until it has cooled down. After about 15 – 20 minutes, the pump will automatically switch on.

**SAFETY INSTRUCTIONS

**

CAUTION!
Risk of injury! Use the machine and the extension cable only in perfect working order. Damaged equipment may not be operated. Do not disable safety and protective devices!

• Children, or people who are not familiar with the operating instructions, are not allowed to use the machine.

• Never lift, transport or suspend the unit using the connection cable.

• Unilateral modifications or conversions of the unit are prohibited.
  Electrical safety
  CAUTION!
  Danger when touching voltage conducting parts!
  Disconnect the plug from the mains if the extension cable is damaged or severed! We recommend connecting an RCD (residual current operated device) having a nominal residual current of < 30 mA.

• The pump may not be operated while people are in the pool or pond.

• The house mains voltage must agree with the details quoted in the technical data, do not use any other supply voltage.

• The unit must only be operated with an electrical installation in accordance with DIN/ VDE 0100, Part 737, 738, and 702. Protection must be provided by a 10 A-line protection switch and an RCCD (residual current operated device) having a nominal residual current of 10/30 mA.

• Use only extension cables that are suitable for use outdoors – minimum cross-section 1.5 mm 2 . Cable drums should always be unrolled completely.

• Damaged or brittle extension cables must not be used. ➯ Check the condition of your extension cable each time you start to use the equipment.

ASSEMBLY

Mounting the pressure line
 You can cut off the tip of the multi-size nipple to fit the diameter of the hose you are using. Using a hose with the largest possible diameter will greatly improve the performance of the pump.

1. Screw the multi-size nipple (10) into the pump outlet.
2. Attach a hose to the multi-size nipple.
3. Fix the connection cable (3) with cable ties to the pressure hose.
4. To submerge the pump into a well or cistern, attach a rope to the rope bracket (4) provided for this purpose.
5. Uncoil the electric cable completely.
6. Plug the pump into the socket. As soon as Adjusting the cut-in and cut-off levels the pump has reached the cut-in (= START) level, the float switch will automatically switch the pump on. When the liquid has fallen below the cutoff (=STOP) level, the pump will automatically switch off, see technical data.

STARTUP

Safety
CAUTION!
Take suitable measures, e.g. installation of an alarm or a backup pump, to ensure that flooding will not occur if the pump should malfunction.

**CAUTION!**

When placing the pump in the liquid, make sure to let it down slowly. You may need to tilt the pump slightly so that air trapped in the body is released. Set the pump on the bottom so that it cannot fall over. If the bottom should be sandy or muddy or rocky and uneven, place the pump on a suitable hard, flat surface or suspend it from a rope attached to a secure object. Make sure to leave adequate room between the pump and the bottom so that it cannot suck up solid matter.
CAUTION!
Make sure that the pump does not suck in solid matter. Sand or other abrasive particles suspended in the liquid will lead to increased wear and tear and may impact the performance of your pump. Before lowering the pump into a well or a cistern, attach a rope to the handle. When placing the pump inside a cistern, make sure that the shaft is large enough for the pump to fit. For min. shaft dimensions, see Figure B.

CAUTION!
Place a cover over the cistern so that no one will fall in.
CAUTION!
When switching the pump on again after removing it from a cistern, make sure that the pressure hose is completely empty otherwise the pump will not automatically vent and it could be damaged.
CAUTION!
Make sure that the pump does not run with a blocked or closed pressure hose.
The pump has a non-return valve (2) on the pump output that prevents the pressure hose from emptying the pump every time it is at a standstill.
Adjusting the cut-in and cut-off levels
The float switch cable is attached to the pump housing. You can adjust the cut-in = START and cut-off = STOP levels for operation by simply changing the height of the switch as desired. Recommended length of the float switch cable is approx. 120 mm.

CAUTION! }
While pumping to the minimum submersed depth, make sure to keep the pump under observation and turn it off by pulling the plug when the minimum submersed depth has been reached to prevent the pump from sucking in air, as this may damage your pump.

If the level of the remaining water drops below the minimum submersed depth, the pump will suck in air. Before using the pump again to drain liquid, the air trapped in the pump will have to be vented (see Setting up and Operating the Pump).

Switching off the Pump
1 To switch off the pump, just pull the plug of the electric cable from the socket.

MAINTENANCE AND CARE

Disconnect the machine from the main power supply before commencing assembly and maintenance work.
Cleaning the pump
After conveying chlorine-containing swimming pool water or fluids that leave a residue, the pump must be flushed out with clear water.
1. Clean the suction slots on the suction foot if necessary with clear water.
STORAGE
In the event of a risk of frost, the system must be drained completely.
DISPOSAL
Do not dispose of worn-out machines or spent batteries (including rechargeable batteries) in domestic waste! The packaging, machine, and accessories are made from recyclable materials and must be disposed of accordingly.

TROUBLESHOOTING

Help in case of malfunctions
CAUTION!
Disconnect the mains plug before any fault rectification work! Faults in the electrical system must be rectified by a qualified electrician.

Clean with a suitable tool through the opening at the back of the motor housing.
Thermal protection switch has swit- ched off.| Wait until the thermal protection switch on the immersion pump switches on again. Take note of the maximum temperature of the conveying medium. Has the immersion pump been inspected?
No mains power.| Check the fuses, and have the power supply checked by a qualified electrician.
The float switch does not switch off when the water level rises.| Send the immersion pump to an AL-KO service facility.
The pump running but does not feed.| Air in the pump housing.| Vent the immersion pump by holding it at an angle.
| Blockage on the suction side.| Remove dirt in the suction area.
| Open the pressure line.
The pressure line closed off.
,
Pressure hose kinked.| Extend the pressure hose.
Feed rate too low| Hose diameter too small.| Use a bigger pressure hose.
Blockage on the suction side.| Remove dirt in the suction area.
Feed head to high.| Observe max. feed head, see technical data!

If the faults cannot be rectified, please contact our customer service department.

EU DECLARATION OF CONFORMITY

We hereby declare that this product, in the version brought into circulation by us, complies with the requirements of the harmonized EU guidelines, EU safety standards, and product-specific standards.

Immersion pump, electrical
Serial number
G3023025| DIVE 5500/3
DIVE 6300/4| AL-KO Gerate GmbH Ichenhauser Str. 14 D-89359 Katz
Duly authorized person
Andreas Hedrich Ichenhauser Str. 14 D-89359 Katz
Katz, den 19.01.2016

Wolfgang Hergeth
Managing Director| EU guidelines
2014/35/EU
2014/30/EU
2011/65/EU| Harmonized standards
60335-1:2012
60335-2-41:2012
62233:2008
55014-1:2012
55014-2:2016
61000-3-2:2014 61000-3-3:2014

2015

**WARRANTY

**

We will address claims for any defects in materials and workmanship during the statutory period of limitation by means of repairs or replacements of our choice. The period of limitation is governed by the laws of the country in which the machine was purchased.
Our warranty applies only if:

• The machine has been properly handled
• The operating instructions have adhered to
• Original replacement parts have been used

The warranty is no longer in effect if:

• Efforts have been made to repair the machine
• Technical modifications have been made to
• The machine has not been used for its intended purpose

The warranty does not cover:

• Damage to paintwork through normal use
• Parts are subject to wear as indicated in the replacement parts list with a box [xxx (x)]
• Internal combustion engines – separate warranty conditions of the respective engine manufacturer apply The warranty period begins with the purchase by the first buyer.

The warranty period begins on the date that appears on the original purchase receipt. In the event of a warranty claim, please your contact supplier or the nearest authorized customer service center with this warranty declaration and the purchase receipt in hand. This warranty does not affect the legal warranty claims by the purchaser against the seller.

DIVE 5500-3
Art. Nr. 113 036

DIVE 6300-4
Art. Nr. 113 037

AL-KO GERATE GmbH
Head Quarter
Ichenhauser St r. 14 I 89359 Kbtz] Deutschland Telefon: (+49)8221;203-0 I
Telefax: (+49)8221197-8199
www.al-ko.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>