Cj Global 24043-DI TWS True Wireless Speaker User Manual
- June 5, 2024
- CJ GLOBAL
Table of Contents
Cj Global 24043-DI TWS True Wireless Speaker
Overview
-
Mode
(LINE IN, MP3, FM, BT)D -
Previous song
(FM: Previous channel) -
Play/ Pause
(FM: Automatic Search) -
Next song
(FM: The next channel) -
USB socket
-
Charging socket (DC 5V)
-
Audio input socket (AUX)
-
Micro SD card socket (TF)
-
Knob (Power Switch and
Volume Control) -
4 inch Speaker
-
Colorful Lights
CHARGING THE SPEAKER
Plug the included cable into any USB wall charger (not included) and into the
Micro USB charging port on the front of the speaker. The red LED by the port
indicates the speaker is
charging. When fully charged, the LED turns off. When using the speaker can be
used on battery power or keeping plugged into the USB wall charger (not
included).
ACCESSORIES
- Speaker x 2
- Micro USB Charging Cable – 2pcs
SPECIFICATION
- Output Power: 5W
- Speaker size: 4″
- Product Size: 170*101231mm
- Control: On/Off/Volume and Mode,
- Play/Pause, Forward, Back
- Input: Bluetooth/AUXUSB/TF/FM
- Signal to noise ratio: 290DB
- Bluetooth version: V5.0
- Operation Range: Up to 10 Meters
- Built-in 1200mAh Lithium Battery
- Recharge time: 3 hours full charge
- Playing time: 6 hours
- Seven colors LED Light
TWS Function
-
Turn on “A” and “B” speakers. Press and hold the “Mode” button on both speakers simultaneously, the speaker will play a chime sound and shortly
after the message “your device has connected successfully” (this prompt means the 2 speakers have paired and connected with each other.
Look for “ON45” on your Bluetooth device and select it from the list of available devices, you will get another voice prompt saying “your device has connected successfully”. -
Once paired and connected to your Bluetooth device you will get True Wireless Stereo Sound.
Bluetooth® connection
- Turn the volume control knob to tun on the speaker and it defaults to Bluetooth mode, you will get a “ding dong” prompt.
- Turn on your other Bluetooth device and search for “ON45” and click on the “ON45”.
- You will get a voice prompt “Your device has connected successfully” , connection is successful.
Micro-SD Function
- Press “MODE” on the product to switch to TF mode or just insert a Micro SD card. TF mode will start automatically.
- Press “PLAY/PAUSE” to continue play/pause music.
- Press “NEXT” button to go to next song.
- Press “PREVIOUS” to go back to the previous song.
USB Function
- Press “MODE” on the product to switch to USB mode or just insert a USB flash drive. USB mode will start automatically.
- Press “PLAY/PAUSE” to continue play/pause music.
- Press “NEXT” button to go to next song.
- Press “PREVIOUS” to go back to previous song.
FM Radio Function
- Press “MODE” on the product to switch to FM mode. Radio will start automatically.
- Press “PLAY/PAUSE” to enter into automatic FM channel searching.
- Press “NEXT” button to go to next frequency.
- Press “PREVIOUS” to go back to previous frequency.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
The Bluetooth” word mark and logos are registered trademarks owned by the Bluetooth IG, Inc. and any use of such marks by CJ Global is under license. Other trademarks and trade names are those of their respective owners.