DIGITUS DN-80068 5 Port 10 or 100Mbps Ethernet Unmanaged Switch Installation Guide
- June 5, 2024
- DIGITUS
Table of Contents
DIGITUS DN-80068 5 Port 10 or 100Mbps Ethernet Unmanaged Switch
Installation Guide
DN-80068
Copyright Statement
Our company reserves all copyrights of this document. Any reproduction,
excerption, backup, modification, transmission, translation or commercial use
of this document or any portion of this document, in any form or by any means,
without the prior written consent of our company is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject
to change without any notice. Please obtain the latest information through our
company website. Our company endeavors to ensure content accuracy and will not
shoulder any responsibility for losses and damages caused due to content
omissions, inaccuracies or errors
1. Product Introduction
The 5-Port 10/100 Mbps Network switch from DIGITUS® provides 5 x RJ45 ports with 10/100Mbps bandwidth each. Easily expand the existing network. No configuration is required on the switch itself; thanks to auto-negotiation and Auto MDI/MDI-X, cables and speeds are also automatically detected. The switch can be used as a desktop variant or mounted on a wall. Thanks to the external power supply, the switch does not need a fan at all. Ideal for expanding / setting up small home or company networks with data rates of up to 100 Mbps.
1.1 Features
- Auto-negotiation / Auto-MDI/MDI-X
- No configuration necessary
- LED indicators for monitoring power, link/activity
- 5 x RJ45 ports 10/100 Mbps
- All ports support 10/100 Mbps bandwidth
- Network standards: IEEE 802.3i, IEEE 802.3u, IEEE802.3x, IEEE802.3az
- Store and forward mode operates
- Full-duplex flow control IEEE802.3x
1.2 Package Contents
Before installing the Switch, make sure that the following the “packing list”
listed OK. If any part is lost and damaged, please contact your local agent
immediately. In addition, make sure that you have the tools install switches
and cables by your hands.
- 1 x 5-Port Fast Ethernet Switch,Unmanaged
- 1 x Power Supply
- 1 x Quick Start Guide
1.3 Hardware Specifications
1.4 External Component Description
Upper Panel
The upper panel of the Switch consists of a series of LED indicators
LED indicators:
The LED Indicators will allow you to monitor, diagnose and troubleshoot any
potential problem with the Switch, connection or attached devices.
The following chart shows the LED indicators of the Switch along with explanation of each indicator.
Front Panel
The front panel of the Switch, consists of 5 x 10/100Mbps RJ-45 ports and a 5V
DC power adapter interface
10/100 Mbps RJ-45 ports (1~5):
Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps. Each
has a corresponding Link/Act indicator.
DC Power Connector:
Power supply via external power adapter, using 5V/500mA external power supply.
Rear Panel
The rear panel of the Switch contains one Grounding Terminal shown as below.
Grounding Terminal:
Located on the right side of the rear panel, use wire grounding to lightning
protection.
2. Installing and Connecting the Switch
This part describes how to install your Ethernet Switch and make connections to it. Please read the following topics and perform the procedures in the order being presented.
2.1 Installation
Please follow the following instructions in avoid of incorrect installation
causing device damage and security threat.
- Put the Switch on stable place or desktop in case of falling damage.
- Make sure the Switch works in the proper DC input range and matches the voltage labeled on the Switch.
- To keep the Switch free from lightning, do not open the Switch’s shell even in power failure.
- Make sure that there is proper heat dissipation from and adequate ventilation around the Switch.
- Make sure the cabinet to enough back up the weight of the Switch and its accessories.
2.2 Desktop Installation
Sometimes users are not equipped with the 19-inch standard cabinet. So when
installing the Switch on a desktop, please attach these cushioning rubber feet
provided on the bottom at each corner of the Switch in case of the external
vibration. Allow adequate space for ventilation between the device and the
objects around it.
2.3 Wall Installation
The Switch can also be installed on a wall. Two installing slots are provided
on the bottom of the Switch for this purpose. Please make sure that the front
panel is exposed in order to view the LEDs. Please refer to the illustration
below:
2.4 Power on the Switch
The Switch is powered on by the External DC adapter 5V/500mA power supply.
Please follow the next tips to connect:
Use the standard DC adapter to connect one end of the power socket to the
power DC interface of the back panel of the switch. And check the power
indicator is ON or not. When it is ON, it indicates the power connection is
OK.
2.5 Connect Computer (NIC) to the Switch
Please insert the NIC into the computer, after installing network card driver,
please connect one end of the twisted pair to RJ-45 jack of your computer, the
other end will be connected to any RJ-45 port of the Switch, the distance
between Switch and computer is around 100 meters. Once the connection is OK
and the devices are power on normally, the LINK/ACT status indicator lights
corresponding ports of the Switch.
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.
www.assmann.com Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>