Bobtot ET26 Waterproof Wireless Speaker User Guide
- June 9, 2024
- Bobtot
Table of Contents
ET26 Waterproof Wireless Speaker User Guide
Whar”s in the Box
Illustration
- Type-C Charging Jack
- USB Port • AUX Port
- Backwardness Down
- Forwardness Up
- Power Button Long-press for power on/off.
- Mic Hole
- Play/Pause
- Mode Button
- Power Button
Function Buttons
Power Button
Long -press for power on/off
Mode Button (TWS, Turn off the light)
Short-press to switch the modes.(AUX/USB/BT) Long-press to pair or disconnect
TWS. Double-press to change the lights mode and turn off the lights.
Play/Pause
Short-press to play or pause. Long-press to disconnect BT connection.
Volume Down/Backward
Short-press for volume down. Long-press for previous song. (only for BT/USB
mode)
Volume Up/Forward
Short-press for volume up Long-press for next song. (only for BT/USB mode)
Charging Your Device
- The charger is not included in the package, please charge this speaker using a USB wall adapter with a DC 5V/1A output.
- Allow about 5 hours to full charge the battery. Note:
- The unit does not have power bank function, it is forbidden to charge other device via this unit or to connect other device via the USB port.
- To protect the battery, please do not use the speaker while it is charging.
Initial Setup
- Once your speaker is fully charged, press and hold the Power button until you hear a voice prompt indicating the device has entered BT paring mode.
- 0n your smartphone or tablet, search for the BT device named “Bobtot ET26” and tap to connect.
- A prompt will play once pairing is successful.
Note: 1. Insert USB flash drive, ET26 speaker will play the audio files automatically. 2. Insert 3.5mm audio cable, ET26 speaker will play sounds of the device.
How to pair your device?
- Please turn on the two speakers and make sure that both are disconnected from your other BT device.
- Select either of the speakers. Long press the Ga Mode button till your hear indicator tone.
- When paired successfully, the LED indicator light of the master speaker will flash with blue and the light on the slave speaker will be off.
- Please use your BT device to search “Bobtot ET26” and connect it. The LED indicator light of master speaker will stay blue. Then you can enjoy the music with two speakers together.
Note: 1. In TWS mode, if you want to turn off, you need to turn off the two speakers seperately. 2. Long press the IN Mode button of the master speaker( which the led light stay blue) 3 seconds to disconnect TWS.
Hands-Free Calling
Volume Down
Short Press to decrease the volume
Volume Up
Short Press to increase the volume
Play/Pause Button
Short press to accept an incoming call. Long press to reject an incoming call.
Long press 2S to switch to talking on the phone. Short press to end the call.
Resetting Your Device If the speaker does not turn off or respond, you can
short-press the OAUx RESET button in Aux Port with a small round pin.
Specifications
- Speaker Size: 2 inch*2
- RMS power output: 10W, 30
- Peak power output: 20W, 30
- Battery Capacity: 3.7V, 4000mAh
- Water resistant: IPX5
- TWS function
- Hands-free Mic
- USB/AUX supported
- Three modes of RGB Lighting
- Frequency Response: 80HZ-16KHZ
- Connecting range: 10m
- Product size: 242(L)92(W)92(H)mm
FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection agains tharmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help. The
device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction.
Need help?
Customer Care Guide
At our company, we strive to provide exceptional customer care to every one of
our clients. We believe that building strong relationships with our ustomers
is essential to the success of our business. To help us achieve this goal, we
have put together the following customer care guide.
Time
We understand that our customers’ time is valuable, so we will respond to any
inquiries within 24 hours.
Feedback
We know that our customers are the heart of our business so we value your
feedback. We encourage you to share your thoughts and ideas with us.
Solutions
If our customers encounter any issues, we will try our best to find a quick
and efficient solution that meets your needs.
Here at Bobtot, we take customer care very seriously.
Our customers are our first priority, and we are committed to providing the
highest quality service If you have any questions or concerns, please don’t
hesitate to reach out to us.We will be happy to assist you:
Call or Message: +1 888 572 1718
Email: service@bobtot.net
bobtot.net 2023 BOBTOT//Features and specifications
are subject to change and or Improvement without notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>