VITEK VT-1303 Hair Dryer Instruction Manual
- June 5, 2024
- VITEK
Table of Contents
VT-1303 Hair Dryer
Instruction Manual
HAIR DRYER VT-1303
The hairdryer is intended for hair drying and styling.
DESCRIPTION
- Air supply speed switch (0\ \ )
- Heating degree switch ( )
- Cool shot button
- Concentrator nozzle
- Air inlet grid
- Hanging loop
- Pilot light
ATTENTION! Do not use the unit near water in the bathrooms, showers, swimming pools etc.
- When using inside a bathroom, always disconnect the appliance from the wall outlet after usage; in particular, unplug the power cord from the wall outlet, as proximity to water is dangerous even if the appliance is switched off.
- For additional protection, it is reasonable to install a residual current device (RCD) with a rated operating current no higher than 30 mA into the power supply circuit of your bathroom. Apply to a competent specialist for installation.
SAFETY PRECAUTIONS
Before using the electrical unit, read this instruction manual carefully and keep it for future reference. Use the unit for its intended purpose only, as specified in this manual. Mishandling of the unit may lead to its breakage and cause harm to the user or damage to his/her property.
- Before switching the unit on, make sure that the voltage of the mains corresponds to the unit operating voltage.
- Never leave the operating unit unattended.
- Do not switch the unit on in places where aerosols are sprayed or highly flammable liquids are used.
- Apply the hair spray only after hair styling is finished.
- Always unplug the unit after usage and before cleaning.
- When unplugging the unit, pull the plug but not the cord.
- Do not touch the unit body and the power plug with wet hands.
- Do not hang or keep the unit in places where it can fall into a bath or a sink filled with water; do not immerse the unit body, power cord or power plug into water or other liquids.
- Do not use the unit while taking a bath.
- If the unit is dropped into water, unplug it immediately and only then take it out of water.
- For children, for safety reasons do not leave polyethylene bags used as packaging unattended.
Attention! Do not allow children to play with polyethylene bags or packaging film. The danger of suffocation!
-
Do not allow children to touch the unit body, the power cord, or the power plug during the operation of the unit.
-
Do not leave children unattended to avoid them using the unit as a toy.
-
Close supervision is necessary when children or people with disabilities are near the operating unit.
-
This unit is not intended for usage by children.
-
During the unit’s operation and breaks between operation cycles, keep the unit away from children.
-
The unit is not intended to be used by people with physical, sensory, or mental disabilities (including children) or by persons lacking experience or knowledge if they are not under the supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
-
Do not use the unit when you are drowsy.
-
Do not use the unit to style wet hair or synthetic wigs.
-
Avoid contact with heated surfaces on your face, neck, and other parts of your body.
-
Do not put the operating unit on heat-sensitive or soft surfaces (for instance, bed or sofa), and do not cover the unit.
-
It is recommended to unwind the power cord to its full length while using the unit.
-
The power cord should not:
– touch hot objects;
– run over sharp edges;
– be used as a handle for carrying the unit. -
Check the power cord integrity from time to time.
-
Do not use the unit if the power cord or the power plug is damaged, if the unit works improperly, and after it was dropped. If the power cord is damaged, it should be replaced by the manufacturer, maintenance service or similarly qualified personnel to avoid danger.
-
Do not attempt to repair the unit. Do not disassemble the unit by yourself, if any malfunction is detected or after it was dropped, unplug the unit and apply to any authorized service center at the contact addresses given in the warranty certificate and on the website www.vitek.ru.
-
To avoid damages, transport the unit in the original package only.
-
Keep the unit in a dry cool place out of reach of children and disabled persons.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY. ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
USING THE HAIRDRYER
After unit transportation or storage at low temperature, it is necessary to
keep it for at least three hours at room temperature before switching it on.
- Unpack the unit and remove any advertising stickers that can prevent the unit’s operation. Unwind the power cord completely.
- Before switching the unit on, make sure that your home mains voltage corresponds to the unit operating voltage.
- Insert the power plug into the main socket.
Switching hair dryer on
Before switching the appliance on make sure the power supply voltage meets the operating voltage of the appliance.
-
Insert power cord plug into a wall outlet.
-
The select operating speed you need using the airflow speed switch (1):
O = the hairdryer is switched off;
= low speed;
= high speed; -
Select airflow temperature you need using the heating degree switch (2).
= slight heating cold air
= medium heating
= maximal heating
= Cool shot function, press and hold the cool shot button for fixing your hairstyle.
Note: – when the hairdryer is switched on, the pilot light (7) lights up.
Taking care of your hair
Before drying and setting your hair, wash them with shampoo, dry with a towel
to remove excess moisture, and brush for better results.
Fast drying
Set switch (2) into a position of maximal heating (position ), select the
airflow speed you need using switch (1), and dry your hair out a little bit.
Shake off excessive moisture by hand or using a brush and continuously move
the hair dryer over your hair.
Straightening your hair
Set switch (2) into a position of maximal heating (position ), select the
airflow speed you need using switch (1), and dry your hair out a little bit.
When your hair is almost dry, install concentrating nozzle (4), reduce the
degree of air heating by a switch (2), and airflow speed by a switch (1).
Divide your hair into locks and layers and start straightening from the lower layers. Using a flat or a round hairbrush, brush the hair downwards while directing hot air from the nozzle (4) at it. In this way, slowly straighten each lock from root to end. After you finish straightening the locks of the lower hair layer, start straightening the locks of the middle layer and finish with the locks of the upper hair layer.
Natural waving structure of your hair
Set switch (2) into a position of slight heating (position ), then set switch
(1) into position , hold a lock between your fingers tightly, turn it to
direction of its natural curliness, then dry the lock out by directing air jet
between the fingers.
After getting the shape you need, press a cool shot button (2) and fix each
lock.
Volume styling
Using a hair dryer in any mode of heating/any speed from slight to maximal,
dry out hair roots beginning from the backside of your head.
Styling your hair
Set switches (1,2) into positions of slight heating and slow speed
correspondingly, and attach concentrating nozzle (4) to provide directed
airflow. Divide your hair into locks and create a required hairstyle using a
round hairbrush. During hair styling direct the airflow straight onto your
hair in the desired direction. If necessary, direct air jet on each lock for
2-5 seconds to fix it. Time of setting locks you should determine on your own
taking into account the type of your hair.
«Cool shot»
This model is equipped with the function of “cool shot”, which can be used for
fixing your hairstyle. Press and hold the “cool shot” button (3) . This option
helps to protect the hairstyle you have created.
PROTECTION AGAINST OVERHEATING
The appliance is equipped with the function of protection against overheating.
This function switches the appliance off if the temperature of outgoing air is
higher than admitted. If the hair dryer is switched off during operation, turn
it off by setting switch (1) into position “0”, take the power cord plug out
of the wall outlet, examine if the air inlet or outlet openings are blocked,
and leave the appliance for a while for cooling down for 5-10 minutes, then
switch it on again.
Do not block air openings while using hair dryer and avoid your hair getting
inside its air inlet opening.
MAINTENANCE AND CARE
The hairdryer is intended for household usage only.
- Set the switch (1) to the “0” position and disconnect the hairdryer from the mains.
- It is recommended to periodically clean the air inlet grid (5).
- Turn the grid (4) counterclockwise and remove it.
- Clean the grid with a brush, install the grid (5) back to its place and turn it clockwise as far as it will go.
- Do not use solvents or abrasives for cleaning of the hairdryer.
STORAGE
- Always unplug the hairdryer if it is not being used.
- Never wind the cord around the hairdryer, as this can damage the cord. Do not pull, twist or stretch the cord, especially near the plug or at the junction point to the unit body. Straighten the cord periodically if it gets twisted during a hairdryer operation.
- For easy usage there is a hanging loop (6), you can store the unit by means of this loop on the condition that no water gets on the unit in this position.
- Keep the hairdryer in a dry cool place out of reach of children and disabled persons.
DELIVERY SET
Hair dryer – 1 piece
Concentrating nozzle – 1 piece
Operating manual – 1 piece
Specifications
Power supply: 220-240 V ~ 50-60 Hz
Rated input power: 1950-2300 W
ATTENTION! Do not use the unit near water in the bathrooms, showers, swimming pools, etc.
RECYCLING
For environment protection do not throw out the unit and the batteries (if
included), do not discard the unit and the batteries with usual household
waste after the service life expiration; apply to specialized centers for
further recycling.
The waste generated during the disposal of the unit is subject to mandatory
collection and consequent disposal in the prescribed manner.
For further information about recycling this product applies to a local
municipal administration, a disposal service, or to the shop where you
purchased this product.
The manufacturer reserves the right to change design, structure, and specifications not affecting general principles of the unit operation without a preliminary notification due to which insignificant differences between the manual and product may be observed. If the user reveals such differences, please report them via e-mail info@vitek.ru for receipt of an updated manual.
Unit operating life is 3 years Guarantee
Details regarding guarantee conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee.
This product conforms to the EMC
Directive 2014/30/EU and to the Low
Voltage Directive 2014/35/EU.
The production date of the item is indicated in the serial number on the
technical data plate.
A serial number is an eleven-unit number, with the first four figures
indicating the production date.
For example, serial number 0606ххххххх means that the item was manufactured in
June (the sixth month) of 2006.