eta Fricool 1172 90000 Electric Deep Fryer with Removable Pot User Manual

June 5, 2024
ETA

eta Fricool 1172 90000 Electric Deep Fryer with Removable Pot

eta-Fricool-Electric-Deep-Fryer-with-Removable-
Pot

SAFETY NOTICE

  • Carefully read the user’s manual before putting the appliance into operation, see the illustrations and save the manual for future use.
  • Check that the voltage on the type label corresponds to the voltage in your electric power socket.
  • The power plug must be connected to a properly installed and grounded power socket.
  • Never use the appliance if the power cord or power plug are damaged, if it is not functioning correctly or if it has fallen on the fl oor and been damaged. In such cases take the appliance to a professional service centre to verify its safety and correct function.
  • Do not insert the power plug into the electric power socket and do not pull it out of the electric power socket with wet hands or by pulling on the power cord!
  • The product is designed only for household use and similar applications (preparing food)!It is not designed for commercial use! It is not designed for outdoor use!
  • This appliance may not be used by any persons (including children) whose physical, sensory or mental disabilities, or insuffi cient experience or knowledge prevent the safe use of the appliance, unless they are supervised or have been properly trained in the safe use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the product.
  • Do not leave the appliance on without supervision and supervise it for the entire time it is frying.
  • Use the deep fryer only in locations, where there is no danger of it tipping over and at a suffi cient distance from fl ammable objects (e.g. curtains, drapes, wood, etc.), heat sources (e.g. fi re stoves, electric/gas stoves, etc.) and wet surfaces (sinks, wash basins, etc.).
  • Before connecting to an electric power socket the deep fryer must be correctly assembled and must contain shortening or oil suitable for frying. The frying basket handles must be properly attached so there is no danger of them slipping out during handling.
  • The deep fryer (heating element) is equipped with thermal overheating protection.
  • Before fi rst use, wash all parts that will come into contact with food.
  • Do not carry the appliance when hot, or when it contains hot contents. In the event of it tipping over there is a danger of burn injuries. When handling the appliance use the handles.
  • Lower the frying basket with food contents slowly into the hot shortening!
  • Never submerge the control panel, power cord or the body of the deep fryer (even partially) under water and do not wash under running water!
  • Never use the deep fryer to heat water.
  • Do not use the independent heating element to heat other liquids (e.g. water) in other containers!
  • While frying do not touch the sides of the pot, the viewing glass in the lid and places where steam is escaping, this presents a danger of burns and scalding. Watch out for the hot steam coming out when the lid is removed!
  • Always allow the deep fryer to fully cool down before inserting or removing its parts, or before cleaning it. Never use the deep fryer if any of its parts are damp or wet!
  • Before frying remove any food packaging (e.g. paper, PE-bags, etc.).
  • Always use quality oil or shortening recommended by the manufacturer for frying.
  • Fill the frying shortening or oil only into a dry and cool pot. Before use cut the shortening into smaller cubes. Do not combine mixes of shortening and oil! This will prevent the contents from boiling over!
  • It is necessary to maintain the level of the frying medium (oil or shortening) between the markings MIN and MAX, to prevent overheating or overfl owing.
  • Always replace the frying medium if it turns brown or if it thickens, has an unpleasant odour or if smoke or froth is emitted when it is heated.
  • When using old frying media there exists a danger of its spontaneous combustion. If sudden combustion (fi re) occurs, disconnect the appliance from the power grid and put out the fi re by closing the lid of the deep fryer.
  • Never place wet foods or foods with pieces of ice into the hot frying medium.
  • Always disconnect the appliance when you have fi nished working with the appliance by pulling the power plug out of the power socket.
  • The power cord must not be damaged by sharp or hot objects, by an open fl ame and it must not be submerged under water. Never place it on hot surfaces and do not leave it hanging over the edge of a table or a work bench. If the cord is tripped over or pulled by for example children the deep fryer may tip over or be pulled down and lead to serious burns!
  • The appliance is portable and is equipped with a fl exible power cord with a plug, which ensures a bipolar disconnection from the electricity grid.
  • If the use of an extension cord is necessary, then it must not be damaged and must meet the valid norms in force.
  • If the power cord of this appliance is damaged, then it must be replaced with a special power cord or a power cord set, available from the manufacturer or their service technician.
  • Only use the appliance with original accessories from the manufacturer.
  • Never use the appliance for any other application than that determined and described in this user’s manual!
  • Do not use the deep fryer with a program, timer switch or any other component that automatically switches on the deep fryer.
  • The manufacturer takes no responsibility for damages caused by the incorrect use of this appliance and its accessories (e.g. spoilage of foods, injuries, burns, scalding, fi re) and takes no responsibility arising from the warranty on this appliance if the above safety notices are not followed.

DESCRIPTION OF THE APPLIANCE (pic. 1)

eta-Fricool-Electric-Deep-Fryer-
with-Removable-Pot-1

A – deep fryer body

  • A1 – guiding grooves
  • A2 – handles

B – pot

C – frying basket

  • C1 – handle

D – control panel

  • D1 – heating element
  • D2 – guiding edges
  • D3 – temperatures control dial
  • D4 – indicator light (ON)

E – lid

  • E1 – viewing window
  • E2 – handle
  • E3 – fi lter

OPERATING INSTRUCTIONS

Remove all packaging materials and take out the deep fryer with its accessories. Remove all adhesive foils, stickers or paper from the deep fryer. Before fi rst use clean the parts that will come in contact with food using hot water with detergent, thoroughly rinse with clean water and wipe dry, if necessary allow to dry.
Assembly of the individual parts (pic. 2, 3, 4, 5, 6)eta-Fricool-Electric-
Deep-Fryer-with-Removable-Pot-8

  • Insert the frying pot B into the body A.
  • Control panel D with the heating element D1 insert into the pot B so that the guiding edges D2 on the control panel slide into the guiding grooves A1 on the body A (an audible click will be heard). If the control panel with the heating element is not correctly attached (inserted), the safety switch D8 will prevent the deep fryer from operating.
  • Attach the handle C1 to the frying basket C by gently pushing the wires towards each other using your fi ngers and sliding the wires into the metal holders and then insert the bent out ends into the holder openings in the basket. Subsequently with gentle pressure secure the holder in place in the locked position (an audible click will be heard).
  • Place the lid E on to the pot B so that the fi lter E3 is facing the control panel.
    Following the reverse order you may again disassemble/remove all the parts (or if required assemble them).

Overheating protection
The deep fryer is equipped with a safety thermal fuse, which disconnects the heating element if the deep fryer is turned on without a suffi cient amount of oil or without any frying medium at all. If after connecting the deep fryer to the electricity grid it does not work, disconnect it from the grid, remove the control panel and using a suitable tool (e.g. a small screwdriver) press the button D6 (RESET).
Place the assembled deep fryer on an even surface (e.g. kitchen table) at a height of at least 85 cm, out of reach of children, connect the power plug D7 to the electrical grid – indicator lights D4 and D5 will turn on. Pour the frying medium into the pot B up to the mark MAX. Using the control dial D3 set the desired temperature (information about the required temperature is found on the food label or in the table in this user’s manual). Allow the medium to full heat up (approx. 10 minutes). The correct temperature is indicated by the indicator light D5. Slowly place the full basket C into the pot B. Subsequently close the lid E and the deep frying may begin. It is normal for steam to be emitted from the lid during deep frying, this is not a defect. We recommend that you regularly stir the foods while frying to prevent them from sticking together. After fi nishing cooking the food turn the dial D3 to the off position. Remove the lid so that you do not come into contact with hot steam, pull the basket above the level of the frying medium and then hang it in the storage position.
Allow excess oil to drip off the food.

Attention
While heating the thermostat may cycle (the indicator light turns on and off). This is not considered to be a defect.

Preparation of fried foods

  • It is necessary to dry wet foods that will be fried (e.g. in a towel). Always put spices on foods after frying, do not put on spices above the frying pot or during the course of frying.
  • Some foods (meat, fi sh) can be battered. When battering pay attention that an even cover is achieved and that excess breadcrumbs are knocked away.
  • Foods such as doughnuts, etc. can fl oat when being fried in the medium without the basket.
  • Chickens etc. cut in half. This will prevent subsequent scalding when removing it from the basket.
  • When frying foods such as French fries, select a higher temperature. On the other hand when frying bulkier foods such as chicken drumsticks or meat balls, select lower temperatures to ensure the foods are evenly fried inside.
  • You will make the best French fries if you fry them in two stages. Before frying them a second time, allow the French fries to cool down.
  • Do not place too many foods on top of each other, they could stick together.
  • Remove excess ice from frozen foods.
  • When frying foods in several stages, wait until the desired temperature is achieved before frying the next load, the indicator light will turn off.
  • When frying several food types, start with those that require the lower temperature.
  • When frying pre-fried foods, use a higher temperature and a shorter frying time than for raw foods.
  • Do not fi ll the basket more than halfway, otherwise the temperature of the medium will fall and the frying result will not be optimal.

WARNING: When frying foods containing a large amount of water or frozen foods, lower the basket into the medium slowly, this will prevent the frying medium from boiling over.

After every frying session
We recommend that you fi lter or strain the lukewarm medium and transfer to an appropriate  container, close the container and store in the refrigerator – this will prevent the formation of unwanted compounds.
WARNING: The hot frying medium will melt a plastic bottle, which presents a hazard!

Please consider the following cooking tips as examples and as inspiration. Their purpose is not to be a guide, but to demonstrate the possibilities of various food preparation methods. Generally, it is recommended to use lower temperatures for brittle foods (vegetables, fi sh) and higher temperatures for frozen foods (French fries, chicken, etc.). Cooking times are in the range of several minutes. eta-Fricool-Electric-Deep-Fryer-with-Removable-
Pot-7

Removing unpleasant odours
Some foods (e.g. fi sh) can give the frying medium an unpleasant odour. This odour may be neutralised using the following method:

  • heat the frying medium to a temperature of 160 °C,
  • place a few shoots of parsley or two slices of bread into the medium,
  • wait until “bubbles” stop forming, then using a suitable utensil remove the parsley or bread. The frying medium will now have a neutral taste.

Filtration or replacement of oil
It is not necessary to replace the oil after every use. If you fry mainly potatoes and fi lter the oil, it is possible to reuse it 8-10x. Do not use the same oil longer than 6 months. To carry out the fi ltration or replacement proceed as follows:

  • Disconnect the deep fryer from the electricity grid
  • pour the fully cooled oil out of the pot B into another container with a suitable volume capacity
  • wash and thoroughly dry the pot B
  • pour the oil back through an appropriate fi ltration paper

MAINTENANCE

Before carrying out any maintenance disconnect the appliance from the power grid by pulling out the plug on the power cord from the el. socket and allow it to cool down! After each use wipe the outer surfaces with a soft damp cloth. Do not use abrasive and aggressive cleaning agents and metal tools, which could scratch the surface during cleaning. Every time the medium is poured out remove any remains of fat or remains from previous frying that have stuck to the heating element D1. Wash all other parts (cover, pot, basket, handle, lid) in hot water with dish-washing detergent, and then rinse out with clean water and allow it to fully dry (you may use a dishwasher). Never dry plastic moulded parts above a heat source (e.g. fi re stoves, electric/gas stoves, etc.). It is normal for the colour of the surface to change over time. This change in no way changes the properties of the surface and is not a reason for complaint about the appliance! Wipe the power cord D7 with a cloth. Store the appliance thoroughly cleaned in a dry, dust-free location that is out of reach of children and incapacitated persons.
Removing the fi lters (E3)
Pull gently to remove the cover from the lid E. Remove the fi lter E3 from the lid. Wash the fi lter in lukewarm water with standard detergent and allow it to dry thoroughly. When dry, place back into the lid. Insert the lugs on the cover into the openings in the lid and click the cover shut.

TROUBLESHOOTING

Problem Cause Solution
Foods are not cooked enough The set temperature is too low or the frying time
is too short Information about temperature and time can be found on the food

label or in the table
Too many food pieces or the food pieces are too large for the basket| Reduce the amount or place smaller pieces of food into the basket, see the information in the table
Steam is escaping from places other

than the ventilation openings in

the lid

| The lid is incorrectly placed| Place the lid correctly on the deep fryer
The permanent fat exhaust filter is clogged or soiled| Wash the lid, see section IV. Maintenance
Problem| Cause| Solution
---|---|---
The frying medium is pouring over the edge of the pot| There is too much frying medium in the pot| Check and if necessary reduce the amount of frying medium so that the marking MAX is not exceeded
There is too much food in the basket| Do not cook large amounts of food at once, if necessary remove some of it
The food contains remains of ice or too much moisture| Before frying remove the ice remains and thoroughly dry the food
While frying the medium froths excessively or emits smoke| The food contains remains of ice or too much moisture| Before frying remove the ice remains and thoroughly dry the food
The frying medium is not suitable for frying| Use oil or shortening suitable for frying
The deep fryer accessories are soiled (food remains)| Clean the deep fryer accessories, see section IV. Maintenance
The frying medium has been used for too long| Replace the frying medium
The deep fryer is emitting an unpleasant odour| The frying medium is no longer fresh| Replace the medium
The medium is not suitable for frying| Use oil or shortening recommended for frying. Do not combine various types of oil and shortening
The deep fryer is not working| The power is not connected| Check the power cord, plug and el. socket
The control panel was not correctly attached| Insert the panel correctly into the attachment board (an audible click will be heard)
The safety thermal fuse was activated| Using a suitable tool press the “RESET” button. If pressing the “RESET” button does not help, contact a professional service centre (see list)

ENVIRONMENT

If the dimensions allow, there are marks of materials used for production of packing, components and accessories as well as their recycling on all parts. The symbols specifi ed on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal, hand them over at the special collection places where they will be accepted free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Ask for more details at the local authority or at a collection site. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. If the appliance is to be put out of operation, after disconnecting it from power supply we recommend its cutoff and in this way it will not be possible to use the appliance again.
More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by professional service! Failure to comply with the instructions of the manufacturer will lead to expiration of the right to guarantee repair!

TECHNICAL DATA

  • Voltage (V): Specifi ed on the type label
  • Input (W): Specifi ed on the type label
  • oil capacity (l):1.9 – 3.5
  • Weight about (kg): 3.3

The product has received ES declaration of conformity according to Act as amended. The product matches the requirements of the below statutory order as amended.

  • Committee Regulation No. 2006/95/ES as amended, setting the technical requirements of the electrical appliance as low.
  • Committee Regulation No. 2004/108/ES as amended, setting the technical requirements of products in terms of their electromagnetic compatibility.

The product is in conformity with the European Parliament and European Committee Regulation No. 1935/2004/ES re. Materials and objects designed for contact with food.
The manufacturer reserves the right for any insignifi cant deviations from the standard fi nished product which do not have any effect on the functioning of the product.
DO NOT IMMERSE IN WATER OR OTHER LIQUIDS.
TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.
ETA a.s., Poličská 444, 539 01 Hlinsko, Czech Republic.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals