Logitech POP Smart Button User Manual

: June 7, 2024
: Logitech

Table of Contents

Logitech POP Smart Button User Manual
Frequently Asked Questions
Factory resetting your POP
Troubleshooting connections
Technical Specifications
Using Sonos groups
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Logitech POP Smart Button User Manual

Frequently Asked Questions

Working with Apple HomeKit
You may use your POP button / switch with the Apple HomeKit, this is achieved entirely through the Apple Home app. You must use a 2.4Ghz network to use POP with Apple HomeKit.

Set up your Apple HomeKit and any other HomeKit accessories you may have, before adding POP. (If you need help with this step, please refer to Apple support)
Open the Home app and tap the Add Accessory button (or + if available).
Wait for your accessory to appear, then tap it. If asked to add an Accessory to the Network, tap Allow.
With the camera on your iOS device, scan the eight-digit HomeKit code on the accessory or enter the code manually.
Add information about your accessory, like its name or the room it’s located in. Siri will identify your accessory by the name you give it and the location it’s in.
To finish, tap Next, then tap Done. Your POP bridge will have a name similar to logi:xx: xx.
Some accessories, like Phillips Hue lighting and Honeywell thermostats, require an additional setup with the manufacturer’s app.
For up-to-date instructions on adding an accessory, directly from Apple, please see:

Add an accessory to Home
You cannot use one POP button / switch simultaneously with the Apple Home app and Logitech POP app, you must first remove your button / switch from one app before adding it to the other. When adding or replacing a POP button/switch, you may be required to factory reset that button/switch (not the bridge) to pair it to your Apple HomeKit setup.

Factory resetting your POP

Factory resetting your POP button/switch
If you are having sync issues with your button/switch, trouble removing it from a bridge using the mobile app, or Bluetooth pairing issues, then you may need to factory reset your button/switch:

Long Press on the button/switch for about 20 seconds.
Re-add the button / switch using the Logitech POP mobile app.

Factory resetting your POP Bridge
If you’re trying to change the account associated with your bridge or restart your setup from scratch for any reason, you’ll need to reset your bridge:

Unplug your POP Bridge.
Plug it back in while simultaneously pressing the Logi logo/button on the front of your bridge for three seconds.
If the LED turns off after rebooting, the reset is not successful. You may not have been pressing the button on your bridge as it was plugged in.

Wi-Fi connections

POP supports 2.4 GHz Wi-Fi routers. The 5 GHz Wi-Fi frequency is not supported; however, POP should still be able to discover devices on your network regardless of what frequency they are connected with. To scan for and detect devices on your network, please ensure your mobile device and POP bridge are both on the same Wi-Fi network. Please note that N mode works with WPA2/AES and OPEN security. N mode does not work with WPA (TKES+AES), WEP 64bit/128bit open or shared encryption such as 802.11 specification standard.

Changing Wi‑Fi networks
Open the Logitech POP mobile app and navigate to MENU > BRIDGES, tap the bridge you’d like to modify. You’ll be guided through changing Wi‑Fi networks for the selected bridge.

Supported Wi‑Fi channels: POP supports all unrestricted Wi-Fi channels, this includes using the Auto channel feature included in most modems within the settings.
Supported Wi‑Fi modes: B/G/N/BG/BGN (Mixed mode is also supported).

Using multiple Wi‑Fi networks
When using multiple Wi‑Fi networks, it’s important to have a separate POP account for each network. For example, if you have a work setup as well as a home setup in different locations with different Wi‑Fi networks, you may decide to use your email for your home setup and another email for your work setup. This is because all of your buttons/switches will appear within your POP account, making multiple setups within the same account confusing or difficult to manage.

Here are some tips when using multiple Wi‑Fi networks:

The social media login option works best when only used for one POP account.
To change the POP account of a button/switch, remove it from its current account using the Logitech POP mobile app, then press the button / switch for about ten seconds to factory reset it. You may now set up your button / switch on a new POP account.

Working with Philips Hue
When it’s time to party, use Pop and Philips Hue to help set the mood. The music is playing and the guests are enjoying themselves, it’s time to POP the party into second gear. Just like that, a playful lighting scene starts and people feel like they can start letting loose. It’s time to party. Things are simple when you use POP with Philips.

Add Philips Hue

Ensure your POP bridge and Philips Hue Hub are on the same Wi‑Fi network.
Open the Logitech POP app on your mobile device and select MENU in the upper left-hand corner.
TapMY DEVICES followed by + and then Philips Hue.
In addition to Hue lights and bulbs, the Logitech POP app will import scenes that were created with the new version of the Philips Hue mobile app. Scenes created with older versions of the Hue app are not supported.

Create a recipe
Now that your Philips Hue device or devices have been added, it’s time to set up a recipe that includes your device(s):

From the home screen, select your button/switch.
Under your button/switch name, select the press configuration you would like to use (single, double, long).
TapAdvanced Mode if you’d like to set this device up using a trigger. (tapping Advanced Mode will also further explain this option)
Drag your Philips Hue device(s) to the centre area where it says DRAG DEVICES HERE.
If needed, tap the Philips Hue device(s) you just added and set your preferences.
Tap ✓ in the upper right-hand corner to complete your POP button / switch recipe.

Troubleshooting connections

Button / Switch to bridge connections
If you’re having trouble connecting your POP button / switch with your bridge, you may be out of range. Ensure your button/switch is near your bridge and attempt to connect again. If your setup results in one or more switches being out of range, you may want to consider adjusting your setup or purchasing an additional bridge. If you continue to experience issues. Factory resetting your button/switch and bridge may resolve the issue.

Mobile to bridge connections
If you’re having trouble connecting your mobile device to your bridge, one of the following issues may be affecting your connection:

Wi‑Fi: Ensure your mobile device has Wi‑Fi enabled and is connected to the same network as your bridge. The 5 GHz Wi-Fi frequency is not supported; however, POP should still be able to discover devices on your network regardless of what frequency they are connected with.
Bluetooth: Ensure Bluetooth is enabled on your mobile device and that both your button/switch and mobile device are close to your POP bridge.
If you continue to experience issues. Factory resetting your button/switch and bridge may resolve the issue.

Working with Harmony Hub
When you go to bed, use POP and Harmony to end your day. For example, a single press on POP may start your Harmony Good Night Activity, your thermostat adjusts, your lights turn off and your blinds lower. It’s time for bed. Things are simple when you use POP with Harmony.

Add Harmony
Provided that you have the most recent Harmony firmware, your Harmony Hub will be automatically detected as part of the Wi-Fi scanning process. There is no need to manually add it unless you are using outdated firmware, or want to add more than one Harmony Hub. To manually add Harmony Hub:

Ensure your POP bridge and Harmony Hub are on the same Wi‑Fi network.
Open the Logitech POP app on your mobile device and select MENU in the upper left-hand corner.
Tap MY DEVICES followed by + and then Harmony Hub.
Next, you’ll need to sign into your Harmony account.

Create a recipe
Now that Harmony Hub has been added, it’s time to set up a recipe:

From the home screen, select your button/switch.
Under your button/switch name, select the press configuration you would like to use (single, double, long).
Tap Advanced Mode if you’d like to set this device up using a trigger. (tapping Advanced Mode will also further explain this option)
Drag your Harmony Hub device to the centre area where it says DRAG DEVICES HERE.
Tap the Harmony Hub device you added, then select the Activity you’d like to control with your POP button/switch.
Tap ✓ in the upper right-hand corner to complete your POP button / switch recipe.
Activities containing a smart lock device will exclude the Smart Lock command.
We recommend controlling August’s smart lock directly using your POP button/switch.

Cleaning your POP
Your POP button/switch is water-resistant, which means it’s ok to clean it using a cloth with rubbing alcohol or soap and water. Do not expose liquids or solvents to your POP Bridge.

Troubleshooting Bluetooth connections
Bluetooth range is impacted by interiors which includes walls, wiring and other radio devices. The maximum Bluetooth range for POP is up to about 50 feet, or about 15 meters; however, your household ranges will vary based on specific electronics in your house and your home’s building structure and wiring.

General Bluetooth troubleshooting

Make sure your POP setup is within range of your device(s).
Make sure your Bluetooth device or devices are fully charged and/or connected to a power source (if applicable).
Ensure you have the latest firmware available for your Bluetooth device(s).
Unpair, then put your device in pairing mode and reattempt the pairing process.

Adding or replacing a POP Bridge
POP has a Bluetooth range of 50 feet, which means if your home setup extends over this range, you’ll need to use more than one bridge. Extra bridges will allow you to extend your setup as far as you want while keeping within Bluetooth range.

To add or replace a POP Bridge to your setup

Open the Logitech POP mobile app and navigate to MENU > BRIDGES.
A list of your current bridge(s) will appear, tap + at the bottom of the screen.
You’ll be guided through adding a bridge to your setup.

Working with Lutron Hub
When you arrive home, use POP and Lutron Hub to lighten the mood. For example, as you enter your house, you single press a POP Switch mounted on the wall near your front door; your blinds go up to let in some daylight and help to create a warm setting. You’re home. Things are simple when you use POP with Lutron.

Add Lutron Hub

Ensure your POP bridge and Lutron Hub are on the same Wi‑Fi network.
Open the Logitech POP app on your mobile device and select in the upper left-hand corner.
Tap MY DEVICES followed by + and then Lutron Hub.
Next, you’ll need to sign into your myLutron account.

Create a recipe
Now that your Lutron Hub device or devices have been added, it’s time to set up a recipe that includes your device(s):

From the home screen, select your button/switch.
Under your button/switch name, select the press configuration you would like to use (single, double, long).
TapAdvanced Mode if you’d like to set this device up using a trigger. (tapping Advanced Mode will also further explain this option)
Drag your Lutron device(s) to the centre area where it says DRAG DEVICES HERE.
If needed, tap the Lutron device(s) you just added and set your preferences.
- When adding blinds, a visual representation of your blinds will appear in the Logitech POP app.
- Within the Logitech POP app, position the blinds to your desired state.
Tap ✓ in the upper right-hand corner to complete your POP button / switch recipe.

Technical Specifications

Required: One of the following Smart Bridge models.

Smart Bridge L-BDG-WH
Smart Bridge Pro L-BDGPRO-WH
Smart Bridge with HomeKit Technology L-BDG2-WH
Smart Bridge Pro with HomeKit Technology L-BDG2PRO-WH.

Compatibility: Lutron Serena wireless shades (not compatible with thermostats or Pico remotes).
Notes: Logitech POP support is limited to one Lutron Smart Bridge at a time.

Working with WeMo
Make your appliances smart, using POP and WeMo. For example, use WeMo wall outlets and a single press on POP may turn on your fan at bedtime. Double- pressing POP may trigger your coffee to start brewing in the morning. Have it all. Things are simple when you use POP with WeMo.

Add WeMo

Ensure your POP bridge and WeMo Switch are on the same Wi‑Fi network.
Open the Logitech POP app on your mobile device and select MENU in the upper left-hand corner.
Tap MY DEVICES followed by + and then WeMo.

Create a recipe
Now that your WeMo device or devices have been added, it’s time to set up a recipe that includes your device(s):

From the home screen, select your button/switch.
Under your button/switch name, select the press configuration you would like to use (single, double, long).
Tap Advanced Mode if you’d like to set this device up using a trigger. (tapping Advanced Mode will also further explain this option)
Drag your WeMo device(s) to the center area where it says DRAG DEVICES HERE.
If needed, tap the WeMo device(s) you just added and set your preferences.
Tap ✓ in the upper right-hand corner to complete your POP button / switch recipe.

Working with IFTTT

Use POP to create your very own IFTTT trigger button/switch.

Turn on your lights with just a tap.
Set your Nest Thermostat to the perfect temperature.
Block off the next hour as busy in Google Calendar.
Track your work hours in a Google Drive spreadsheet.
Many more Recipe suggestions on IFTTT.com.

Add IFTTT

Ensure your POP bridge is connected to the same Wi‑Fi network.
Open the Logitech POP app on your mobile device and select MENU in the upper left-hand corner.
Tap MY DEVICES followed by + and then IFTTT. You will be directed to a webpage and then back to the POP app a few moments later.
Return to the POP edit screen and select a POP button/switch. Drag IFTTT up to a single press, double press or long press action. This will allow the IFTTT website to assign an event to this trigger.

Create a recipe
Now that your IFTTT account has been added, it’s time to set up a recipe for your POP button / switch to control:

From the IFTTT website, sign in to your IFTTT account.
Search for Recipes that include Logitech POP.
You will be asked to connect with your POP. Enter your Logitech POP username and password when prompted.
Continue to configure your Recipe. Once complete, your POP will trigger this IFTTT Recipe.

Working with August Smart Lock
Time to POP and lock. For example, a single press on your POP may unlock your door when guests arrive, then a double press may lock your door as they leave. Your house is secure. Things are simple when you use POP with August.

Add August

Ensure your POP bridge and August Connect are on the same Wi‑Fi network.
Open the Logitech POP app on your mobile device and select MENU in the upper left-hand corner.
Tap MY DEVICES followed by + and then August Lock.
Next, you’ll need to sign into your August account.

Create a recipe
Now that Harmony Hub has been added, it’s time to set up a recipe that includes your August Smart Lock device(s):

From the home screen, select your button/switch.
Under your button/switch name, select the press configuration you would like to use (single, double, long).
Tap Advanced Mode if you’d like to set this device up using a trigger. (tapping Advanced Mode will also further explain this option)
Drag your August device(s) to the centre area where it says DRAG DEVICES HERE.
If needed, tap the August device(s) you just added and set your preferences.
Tap ✓ in the upper right-hand corner to complete your POP button / switch recipe.

Please note that August Connect is needed to use an August Lock device with your POP button/switch.

Replacing your POP battery
Your POP button/switch uses two CR2032 batteries which should last around five years under normal use.

Remove battery

Peel back the rubber cover on the back of your button/switch using a small flat-head screwdriver.
Use a #0 Phillips screwdriver to remove the screw at the centre of the battery holder.
Remove the flat metal battery cover that you just unscrewed.
Remove the batteries.

Insert battery

Insert batteries + side up.
Replace the flat metal battery cover and tighten the screw.
Re-attach the button / switch cover.

When re-attaching the button / switch cover, be sure to position the batteries at the bottom. The Logi logo should be directly on the other side and above the batteries if positioned correctly.

Working with LIFX
Use POP and LIFX to get ready for the big game. For example, before your guests arrive, a single press on POP may set the lights to your team’s colours and create an environment to be remembered. The mood is set. Things are simple when you use POP with LIFX.

Add LIFX

Ensure your POP bridge and LIFX bulb(s) are on the same Wi‑Fi network.
Open the Logitech POP app on your mobile device and select MENU in the upper left-hand corner.
Tap MY DEVICES followed by + and then.
Next, you’ll need to sign into your LIFX account.

Create a recipe
Now that your LIFX Hub device or devices have been added, it’s time to set up a recipe that includes your device(s):

From the home screen, select your button/switch.
Under your button/switch name, select the press configuration you would like to use (single, double, long).
Tap Advanced Mode if you’d like to set this device up using a trigger. (tapping Advanced Mode will also further explain this option)
Drag your LIFX bulb(s) to the centre area where it says DRAG DEVICES HERE.
If needed, tap the LIFX device(s) you just added and set your preferences.
Tap ✓ in the upper right-hand corner to complete your POP button / switch recipe.

Working with Hunter Douglas
When you leave for the day, use POP and Hunter Douglas to preserve your privacy. For example, as you’re leaving your house, you singly press a POP button / switch mounted on the wall near your front door; your connected blinds all go down. It’s time to leave. Things are simple when you use POP with Hunter Douglas.

Add Hunter Douglas

Ensure your POP bridge and Hunter Douglas are on the same Wi‑Fi network.
Open the Logitech POP app on your mobile device and select MENU in the upper left-hand corner.
Tap MY DEVICES followed by + and then Hunter Douglas.
Next, you’ll need to sign into your Hunter Douglas account.

Create a recipe
Now that your Hunter Douglas device or devices have been added, it’s time to set up a recipe that includes your device(s):

From the home screen, select your button/switch.
Under your button/switch name, select the press configuration you would like to use (single, double, long).
Tap Advanced Mode if you’d like to set this device up using a trigger. (tapping Advanced Mode will also further explain this option)
Drag your Hunter Douglas Device(s) to the center area where it says DRAG DEVICES HERE.
If needed, tap the Hunter Douglas device(s) you just added and set your preferences.
- This is where you’ll select which scene to use with POP.
- Scenes are set up using the Hunter Douglas app.
Tap ✓ in the upper right-hand corner to complete your POP button / switch recipe.

Technical Specifications
Required: Hunter-Douglas PowerView Hub.
Compatibility: All shades and blinds that are supported by the PowerView Hub, and multi-room scenes cannot be imported.
Notes: Logitech POP supports starting scenes, but does not support control of individual coverings. Support is limited to one PowerView Hub at a time.

Working with Circle
Enjoy push-button control with Logitech POP and Circle Camera. Turn the camera on or off, switch Privacy Mode on or off, start manual recording, and more. You can add as many of your Circle Cameras as you like.

Add Circle Camera

Ensure your mobile device, POP Home Switch, and Circle are all on the same network.
Open the Logitech POP app on your mobile device and select MENU in the upper left-hand corner.
Tap MY DEVICES followed by + and then Circle.
Next, you’ll need to sign in to your Logi account.

Create a recipe
Now that your Circle device or devices have been added, it’s time to set up a recipe that includes your device(s):

From the home screen of the POP app, select the button or switch that you would like to use.
Under your switch name, select the press configuration you would like to use (single, double, long).
Tap Advanced Mode if you’d like to set this device up using a trigger. (tapping Advanced Mode will also further explain this option)
Drag your Circle device(s) to the centre area where it says DRAG DEVICES HERE.
If needed, tap the Circle device(s) you just added and set your preferences.
- Camera On/Off: Turns the camera on or off, defaulting to whichever settings were last used (Privacy or Manual).
- Privacy Mode : Circle Camera will stop streaming and turn off its video feed.
- Manual Recording: Circle will live stream while recording (10, 30, or 60 seconds) , and the recording will appear in the timeline of your Circle app.
- Live Chat: Sends a request to your phone to open the Circle app in Live view, and use the push-to-talk feature in the Circle app to communicate.
Tap ✓ in the upper right-hand corner to complete your POP Switch recipe.

Working with Osram Lights
Use POP and Osram Lights to get ready for the big game. Before your guests arrive, POP the lights to your team’s colours and create an environment to be remembered. The mood is set. Things are simple when you use POP with Osram Lights.

Add Osram Lights

Ensure your POP bridge and Osram Lights bulb(s) are on the same Wi‑Fi network.
Open the Logitech POP app on your mobile device and select MENU in the upper left-hand corner.
Tap MY DEVICES followed by + and then Osram Lights.
Next, you’ll need to sign into your Osram Lights account.

Create a recipe
Now that your Osram Lights hub device or devices have been added, it’s time to set up a recipe that includes your device(s):

From the home screen, select your button/switch.
Under your button/switch name, select the press configuration you would like to use (single, double, long).
Tap Advanced Mode if you’d like to set this device up using a trigger.
(tapping Advanced Mode will also further explain this option)
Drag your Osram Lights bulb(s) to the centre area where it says DRAG DEVICES HERE.
If needed, tap the Osram Lights device(s) you just added and set your preferences.
Tap ✓ in the upper right-hand corner to complete your POP button / switch recipe.

Technical Specifications
Required: Lightify Gateway.
Compatibility: All Lightify bulbs, light strips, garden lights, etc. (not compatible with Lightify Motion and Temperature Sensor, or Lightify buttons/switches).
Notes: Logitech POP support is limited to one Lightify Gateway at a time. If your Osram device isn’t discovered, restart your Osram Lightify bridge.

Working with FRITZ!Box
Make your appliances smart, using POP, FRITZ! Box, and FRITZ!DECT. For example, use FRITZ!DECT wall outlets to POP on your bedroom fan at bedtime. Double POP and your coffee starts brewing in the morning. Have it all. Things are simple when you use POP with FRITZ! Box.

Add FRITZ! Box & FRITZ!DECT

Ensure your POP bridge and FRITZ!DECT Switch are all on the same FRITZ! Box Wi‑Fi network.
Open the Logitech POP app on your mobile device and select MENU in the upper left-hand corner.
Tap MY DEVICES followed by + and then FRITZ!DECT.

Create a recipe
Now that your FRITZ!Box and FRITZ!DECT devices have been added, it’s time to set up a recipe that includes them:

From the home screen, select your button/switch.
Under your button/switch name, select the press configuration you would like to use (single, double, long).
Tap Advanced Mode if you’d like to set this device up using a trigger. (tapping Advanced Mode will also further explain this option)
Drag your FRITZ!DECT device(s) to the centre area where it says DRAG DEVICES HERE.
If needed, tap the FRITZ!DECT the device(s) you just added and set your preferences.
Tap ✓ in the upper right-hand corner to complete your POP button / switch recipe.

Technical Specifications

Required: FRITZ!Box with DECT.
Compatibility : FRITZ!DECT 200, FRITZ!DECT 210.
Notes: POP support is limited to one FRITZ!Box at a time.

Advanced Mode

By default, your POP functions like a button/switch. One gesture to turn on a light and the same gesture to turn it off.
Advanced Mode allows you to use your POP like a trigger. One gesture to turn a light on and another gesture to turn it off.
After you have turned Advanced Mode on, devices in the recipe for that gesture default to the ON state. Simply tap on the device state to select between ON or OFF.
Some devices may have additional controls when in advanced mode.

Access Advanced Mode

Launch the Logitech POP mobile app.
Select the button / switch you would like to edit.
Navigate to the device you’re editing.
Tap Advanced Mode.

Renaming your POP
Renaming your POP button/switch can be accomplished using the Logitech POP mobile app.

From the mobile app, tap the button / switch you would like to rename.
Long press the button/switch name, which is located near the top of your screen.
Rename your button/switch as needed, then tap Done.
Finally, tap ✓ in the upper right-hand corner.

Working with Sonos
Import your Sonos Favorites and stream music directly from Pandora, Google Play, TuneIn, Spotify, and more. Sit down and POP on some music. Things are simple when you use POP with Sonos.

Add Sonos

Ensure your POP bridge and Sonos are on the same Wi‑Fi network.
Open the Logitech POP app on your mobile device and select MENU in the upper left-hand corner.
Tap MY DEVICES followed by + and then Sonos.

Create a recipe
Now that your Sonos device or devices have been added, it’s time to set up a recipe that includes your device(s):

From the home screen, select your button/switch.
Under your button/switch name, select the press configuration you would like to use (single, double, long).
Tap Advanced Mode if you’d like to set your button / switch to skip songs rather than play/pause, or if you’d like to set this device up using a trigger. (tapping Advanced Mode will also further explain this option)
- By default, your button/switch will be configured to either Play or Pause Sonos. However, by using Advanced Mode you can instead configure POP to Skip Forward or Skip Backward when pressed.
Drag your Sonos device or device(s) to the centre area where it says DRAG DEVICES HERE.
Tap the Sonos device(s) you just added to select a favourite station, volume and device state preferences.
- If you add a new favourite station to Sonos after your POP setup, add it to POP by navigating to MENU > MY DEVICES then tap the refresh icon ↻ located to the right of Sonos.
Tap ✓ in the upper right-hand corner to complete your POP button / switch recipe.

Using Sonos groups

Sonos enhancements support detecting and grouping multiple devices. Grouping multiple Sonos:

Drag and drop one Sonos device over the top of another to create a group.
All Sonos devices can be grouped (e.g., a PLAY-1 with a Play bar).
Tapping on a group name provides additional options to select Sonos favourites.

Additional group rules

If you add just one Sonos device to a recipe it will work as usual. If the Sonos was a member of a group, it gets broken out of that group and the old group stops working.
If you add two or more Sonos devices to a recipe and set them all to the same favourite, then this will also create a Sonos group that plays in sync. This will allow you to set different volume levels for the Sonos devices in the group.
Sonos devices that are part of a group may or may not be able to utilize some POP Advanced Mode features. This is because Sonos internally manages groups by having one device coordinate events and only that device will react to pause/play commands.
If your Sonos device(s) is configured as a secondary speaker in a stereo pair, it will not show up when detecting devices. Only the primary Sonos device will appear.
In general, creating and annihilating groups may take some time, be patient and wait until things have settled before starting the next command.
Using POP to control any secondary Sonos speakers independently will remove the grouping from both the Sonos and POP apps.
When making changes to your device(s) using the Sonos app, please refresh Sonos within the Logitech POP app to sync your changes.

Working with SmartThings
Update 18th July, 2023:With the recent SmartThings platform update, Logitech POP will no longer control SmartThings.

Important changes – 2023
Following a recent change made by SmartThings on their interface, Logitech POP devices can no longer connect/control SmartThings devices. However, existing connections may work until SmartThings deprecates their old libraries. If you delete SmartThings from your Logitech POP account, or factory reset POP, you’ll no longer be able to re-add or reconnect SmartThings with Logitech POP. When you wake up, use POP and SmartThings to start your morning. For example, a single press on your POP can activate your SmartThings power outlet, which turns on your lights and coffee maker. Just like that, you’re ready to start your day. Things are simple when you use POP with SmartThings.

Add SmartThings

Ensure your POP bridge and SmartThings are on the same network.
Open the Logitech POP app on your mobile device and select MENU in the upper left-hand corner.
Tap MY DEVICES followed by + and thenSmartThings.
Next, you’ll need to sign into your SmartThings account.

Create a recipe
Now that your SmartThings device or devices have been added, it’s time to set up a recipe that includes your device(s):

From the home screen, select your button/switch.
Under your button/switch name, select the press configuration you would like to use (single, double, long).
Tap Advanced Mode if you’d like to set this device up using a trigger. (tapping Advanced Mode will also further explain this option)
Drag your SmartThings device(s) to the centre area where it says DRAG DEVICES HERE.
If needed, tap the SmartThings device(s) you just added and set your preferences.
Tap ✓ in the upper right-hand corner to complete your POP button / switch recipe.

Please note that Logitech recommends you connect Philips Hub bulbs directly to POP and exclude them when connecting with SmartThings. The experience will be better for colour control.