eta 90061 Kitchen Maschine User Manual

eta 90061 Kitchen Maschine

Dear customer, thank you for purchasing our product. Please read the operating instructions carefully before putting the appliance into operation and keep these instructions including the receipt and, if possible, the box with the internal packing.

SAFETY NOTICE

• Consider the instructions in the user‘s manual as a part of the appliance and provide it to other users of the appliance.

• Check that the voltage on the type label corresponds to the voltage in your electric power socket.

• This appliance shall not be used by children. Keep the appliance and its power cord away from children. Children shall not play with the appliance.

• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and if they understand the hazards involved.

• If the power cord of the appliance is corrupted, it has to be replaced,by the manufacturer, its service technician or a similarly qualified person to prevent dangerous situations.

• Before exchanging any accessories or accessible parts that are moving during use, before assembly and disassembly, before cleaning and maintenance or after finishing the work, switch off the appliance and disconnect it from mains by unplugging the power cord plug from the electrical socket!

• Always unplug the appliance from the power supply if you leave it unattended and before assembly, disassembly or cleaning.

• Never use the appliance if the power cord or power plug is damaged, if the appliance is not correctly operating if it has fallen on the floor and been damaged, or if it has fallen into water. In such cases take the appliance to a professional service centre to verify its safety and correct function.

• When handling the appliance, especially during the installation of any accessories, removing food from containers and cleaning, please proceed carefully – some accessories are sharp. Injury is imminent if the appliance is used contrary to the operation manual.

• Do not insert the power plug into the electric power socket and do not pull it out of the electric power socket with wet hands or by pulling on the power cord!

• When the appliance is in operation, prevent pets, plants or insects from getting in contact with it.

• Do not plug the power cord in the electrical socket and do not unplug it with wet hands or by pulling the power cord!

• The appliance is intended for home use and for similar purposes (in shops, offices and similar sites, in hotels, motels and other residential premises, or in facilities providing bed and breakfast service). It is not intended for commercial use!

• When not using the blender, the A8 cover must be properly secured.

• Watch the appliance for the entire time of food processing!

• Do not place any objects on the top of the appliance.

• Only use the appliance in the working position at places with no risk of overturning and in a sufficient distance from other objects (such as curtains, drapes, etc.), heat sources (e.g. fireplace, heater, stove, cooker, radiators, hot air ovens, grills) and wet surfaces (e. g. sinks, wash basins).

• This appliance is not intended for outdoor use.

• The appliance must not be used in a damp environment and in any environment with the danger of fire or explosion (premises where chemicals, fuels, oils, gases, paints and other flammable or volatile materials are stored).

• Never immerse the drive unit (or any part of it) in water!

• Before preparation, remove possible packages of food (e.g. paper, a PE bag, etc.).

• Do not turn on the appliance without any ingredients inside!

• Always use only one function of the appliance, and never turn on several functions at the same time (e.g. processing food in the bowl B1 and at the same time in the blender F).

• Do not exceed the maximum time of uninterrupted operation – see the table.
  Never exceed the total time of 30 minutes of uninterrupted operation. Then let the food processor cool down for at least 30 minutes.

• Before connecting the appliance to the mains, make sure it is turned off.

• Your foot processor is fitted with an electronic speed sensor control that is designed to maintain the speed under different load conditions. You may therefore hear some variation in speed during the operation as the foot processor adjusts to the load and speed selected – this is normal.

• The appliance is equipped with a thermal safety fuse that disconnects the current supply incase of engine overloading. If it occurs, unplug the appliance and let the appliance get cooled.

• For safety reasons, it is not possible to exchange the attachments while the drive unit
  is in operation.

• Containers are not intended for storing and storing food. After processing, place the food in another container suitable for storage.

• If the processed foods stick to the accessories (e.g. whisks, kneading hooks, blender blades), lid or container, turn off the appliance and clean the accessories carefully with a spatula.

• Do not insert accessories into any body cavities.

• When assembling accessories, carefully follow the instructions for use. Any other assembly combinations are not permissible, otherwise the appliance shall not properly work!

• Before removing accessories from the drive unit, allow the rotating parts to stop completely.

• When mounting or removing the bowl, do not apply much pressure on the bowl handle.

• Do not lift and carry the food processor using the bowl handle, but always use the recesses at the bottom of the drive unit!

• Prevent your hair, clothing and accessories from getting too close to the rotating parts to prevent catching and winding them!

• Should excessive vibration occur when using this attachment, either reduce the speed or stop the machine and remove some of the contents.

• ATTENTION : Do not use this processor in series with an external timer, remote controller or any other device that switches on the appliance automatically, since a fire risk exists when the processor is accidentally covered or displaced at the moment it switches on.

• Make sure that the power cord does not come into contact with the rotating part of the appliance.

• The power cord must not be damaged by sharp or hot objects, or by an open flame and it must not be submerged under water.

• Never place it on hot surfaces and do not leave it hanging over the edge of a table or a work bench. If the cord is brushed against or pulled by for example children the appliance may tip over or be pulled down and lead to serious injuries!

• If the use of an extension cord is necessary, then it must not be damaged and must meet the valid norms in force.

• Only use the appliance with original accessories from the manufacturer.

• Use this appliance only for the purpose for which it was designed as specified in this user‘s manual. Never use the appliance for any other purpose.

• WARNING : There is a risk of injury in case of incorrect use (not by the manual) of the appliance.

• All text in other languages and pictures shown on the packaging, or the product itself, are translated and explained at the end of this language mutation.

• The manufacturer takes no responsibility for damages and injuries caused by the incorrect use of supplementary machines and accessories (e.g. ruining of foods, injury, cuts) and takes no responsibility on the appliance in the case that the above safety notices were not followed.

Notice!
An integral part of this manual is also a table with the contents of the robot TAB package and instructions for accessories AC .

PREPARATION AND USE

First, remove all packaging materials, and take out the food processor and all accessories. Then remove all adhesive foils, stickers and paper from the food processor and accessories. Before the first use, wash all parts, which will be in contact with food, in warm water with a mild detergent, thoroughly rinse in clear water and wipe dry or let dry. Put the assembled food processor with the selected attachments on a flat, stable, smooth and clean worktop, out of reach of children and incapacitated people. Provide sufficient free space for ventilation. The feet must not be removed. The electric power socket must be easily accessible to allow easy disconnecting of the food processor in the case of an emergency.

FOOD PROCESSOR AND ATTACHMENT

Description

• A1 – Multifunctional head release lever
• A2 – Speed regulating knob
• A3 – Bottom mount for adapters C1 – C3
• A4 – Front mount for attachments
• A5 – Release button
• A6 – Removable cover
• A7 – Multifunctional head
• A8 – Cover
• A9 – Mount for attachments (F)
• A10 – Power cord
• A11 – The Light
• B1 – Stainless bowl
• B2 – Bowl lid
• B3 – Feed tube cover

FOOD PROCESSOR CONTROL

TILTING THE MULTIFUNCTIONAL HEAD DOWNWARD/UPWARD (FIG. 2)
Rotating the release lever A1 slightly will lift the head upward. Rotating the lever A1 further and pushing the unit down will tilt the head downward.

ON/OFF SWITCHING OF THE FOOD PROCESSOR
Before you switch on the food processor, plug the A10 power cord into the electric socket (light A11 lights up). Then switch on the food processor by rotating the speed regulating knob A2. After you finish working, switch off the food processor by rotating the speed regulating knob to position 0 and unplug the power from the mains (light A11 goes out).

SPEED CONTROL (FIG. 5)
Speed is controlled by setting the speed regulating knob A2 to the desired position within the interval 1 – 2 – 3 – 4 – 5 – 6 – 7 – 8. For short operation time at the maximum speed, the regulating knob can be set to position “P” (PULSE). The regulating knob must be held
by hand in this position. Releasing the regulating knob will return it to position 0 and stop rotating.

MULTIFUNCTIONAL HEAD ATTACHMENT SECURITY SAFEGUARD
To disassemble the food processor and to remove the attachments from A4 front mount for attachments, apply a reverse procedure. Before removing the attachments from the motor unit head, you first have to push the release button A5.
Food processing time depends on the volume, type and quality of the processed ingredients. It usually takes several minutes under normal conditions.

WHIPPING, MIXING WHISK, KNEADING HOOK

Description (Fig. 1)

• C1 – Mixing whisk
• C2 – Whipping (wire) whisk
• C3 – Kneading hook
• C6 – Release lever

Safety hints and tips

• About the bowl size, please note that the food processor is not able to sufficiently whip/knead very small amounts of food. For optimum results input at least 300 g of food (if you are whisking egg whites, use at least 2 eggs).
• Never fill the bowl with water or other liquid to the maximum level. Respect the maximum allowed capacity (see the Table of Use, Chapter IV).
• When tilting the multifunctional head upward, control / slow down its rotation by hand.
• The food processor is fitted with a security safeguard, which will switch off the motor once the multifunctional head is tilted upward (during operation). After the head is titled back into the working position, the motor will remain switched off. To turn it on, you have to return the speed regulating knob A2 to position 0.

ASSEMBLY FOR WORK WITH ATTACHMENTS

Assemble the food processor according to the instructions in Figures No. 2, 3 and 4 by lifting the multifunctional head up and putting the bowl lid on its bottom side. Then put the bowl with the food in the lower section of the food processor. Then install the desired adapter on the mount, and tilt the multifunctional head downward to the working position. Apply reverse sequence to remove/exchange the adapter.

SETTING THE OPTIMUM HEIGHT OF ADAPTERS (FIG. 8)
If the adapter hits the bowl bottom or does not reach the ingredients on the bowl bottom, adjust the height. Please proceed as follows: First, install the desired adapter in the food processor, and tilt the empty bowl and the multifunctional head A7 downward to the working position. Then hold the adapter in one hand and release the adapter nut by a Spanner C6. Adjust the height by rotating the adapter clockwise or anticlockwise by hand. The adapter will move downward or upward inside the unit. The adapter end should be as close as possible to the bowl bottom and walls but must not touch them. After the height is adjusted, properly tighten the nut.

USE

• A) Whipping
  • Use the whipping whisk C2 to whip cream, eggs and egg whites.
  • Adjust the processing speed according to the volume, type and quality of the food you are processing, in the interval 1 to 8.
  • The maximum amount of food per processing cycle is 1.2 l.
  • Never use the whipping whisk for kneading heavy dough or mixing light dough!
• B) Mixing
  • Use the mixing whisk C1 for light dough, cake mixtures, cookies, glazes, fillings, mashed potatoes, etc.
  • Adjust the processing speed according to the volume, type and quality of the food you are processing, in the interval 1 to 5.
  • The maximum amount of ingredients per processing cycle is about 2.5 kg.
  • Never use the mixing whisk for kneading heavy dough!
• C) Kneading
  • Use the kneading hook C3 for kneading crispy/light / heavy dough.
  • Adjust the processing speed according to the volume, type and quality of the food you are processing, in the interval 1 to 3.
  • If you process a larger amount of dough, process it in several batches. The maximum amount of ingredients per processing cycle is about 1.6 kg. Do not run more than four consecutive cycles. Make a break of at least 30 minutes before you continue

GLASS BLENDER

Description (Fig. 6)

• F1 – Container lid
• F2 – Container support
• F3 – Knife
• F4 – Knife sealing
• F5 – Removable stopper
• F6 – Glass container
• F7 – Pusher
• F8 – Lock
• F9 – Lock button

Safety hints and tips

• Do not let the blender run without any food!
• Never pour boiling liquids in the container. High temperatures could damage the container and cause breaking the glass. Always put the lid and stopper on the container before switching the appliance. Never remove the container lid F1 when the motor unit is running.
• Before removing the blender lid or container, wait until the rotating parts completely stop.
• When mixing liquids, never use larger volume than the level marked on the container.
• You may also process hot liquids up to 80 °C, for example, sauces or soups.
• Do not use the F8 lock as a handle to carry the blender.

ASSEMBLY

Assemble the blender and attach it to the blender mount A9 according to Figures 6 a 7 (when installing, first place it against the mounting marks ( placed on A8 and F2) and then press it and turn it to lock it in the end position). Instead of the plug for adding liquids F5 you can also insert the pusher F7 in the opening in the lid if you are going to use it. Apply reverse sequence to disassemble the unit and to remove it from the mount – tighten the F2 base properly until the F9 button clicks!

BEFORE THE FIRST USE

We recommend washing the glass container before using it for the first time. The knife section is treated with oil not harmful to health for technological reasons. Therefore first fill in the container with warm water (max. 50 °C) with a small amount of detergent.
Then put the container on the food processor, set the maximum rotational speed and
run for 1 minute. Then rinse the container with clear water.

USE

The blender is designed to mix juices, milk cocktails, soups, sauces, children’s food and dietetic food, light dough, biscuit dough, puree, etc. Remove the lid, put or pour the food into the container and replace the lid. To press larger pieces of ingredients to the knife, use the pusher F7. Always set the speed about the kind and amount of ingredients being processed, and particularly about the ripeness of fruit and vegetables.
We recommend that you always switch on the blender to minimum revolutions and then gradually increase the performance as required.
The recommended processing speed is 1 to 8.

Tips

• When the appliance is in operation, it is only possible to add liquid ingredients (e.g. water, milk, oil, etc.).
• If you are going to process a larger amount of food, divide it into batches not to overload the motor unit of the multifunctional head.
• Never use the pusher F7 individually without the lid F1.
• Cut tougher substances into small pieces, otherwise, the knife F3 will soon become blunt.
• If you are going to mix ice cubes, their size should not exceed 20 x 20 x 30 mm, otherwise, the knife F3 becomes blunt or the motor unit is overloaded.
• Never fill the container with liquids producing foam (for example milk) up to the „MAX“ level to prevent overspill. We recommend 1 litre at maximum.
• Soak hard food (such as legumes, soybeans, etc.) in water before further processing.

TABLE OF APPLIANCE USE AND ATTACHMENTS

Please consider the following processing tips as examples and inspiration. They are not intended as complete instructions, they just show possible variants of food processing. Choose the volume of the processed food so that the maximum volume of containers will not be exceeded. Larger volumes must be divided into several batches, and the container level must be continuously checked. We recommend occasional interrupting of operation, switching off the appliance and removing any food stuck on or blocking attachments.

Attachment| Food| Max. amount| Time (min.)| Speed
---|---|---|---|---

Mixing whisk (C1)

| Recipe / together| Plain flour| 1000 g (1330 ml)|

2 to 5

|

1 to 5

Powdered sugar| 500 g (625 ml)
Milk| 400 ml
Eggs| 8 pcs (360 ml)
Oil| 250 ml
Total volume| 3000 ml
Whipping whisk

(C2)

| Cream (incl. 38 % fat)| 1200 ml| 10| 1 to 8
Egg-white| 15 pcs| 5| 8

Kneading hook (C3)

(bread / * gluten-free bread recipe)

| Recipe / together| Flour| 1000 g|

1 minute at 1 , then higher

speed (max. 3 ) for 4 minutes

Salt| 10 g
Yeast| 15 g / 20 g
Sugar| 10 g / 0 g
Water| 575 g / 350 g
Fat| 10 g / 0 g
Attachment| Food| Max. amount| Time (min.)| Speed
---|---|---|---|---

Blender (F)

| Milk| 1000 ml|

2

|

1 to 8 (P)

Carrot (max. 4 cm)| 250 g
Ice (30 x 20 x 20 mm)| 340 g

MAINTENANCE

Do not use harsh and abrasive detergents for maintenance and cleaning! Ensure that the contact surfaces and sealing elements are clean and functional. You can use a dishwasher to clean the following parts – accessories B2, B3, C1-C3, the whole blender F except the removable blade F3. Some foods may colour the respective attachment to a certain extent. However, this shall not have any effect on the appliance operability and does not constitute a reason to file a complaint! The colouring will usually spontaneously disappear after some time. Never dry plastic mouldings above a heat source (such as a stove, or electric/gas oven).

Multifunctional head and food processor body A
Clean them with a damp cloth soaked in water with a detergent. Avoid water getting in the internal components! If the power cord becomes dirty, wipe it with a damp cloth.

Stainless bowl B1
Clean the component with a cloth soaked in water with a detergent. Do not use steel wool, wire brush or bleaching agent for cleaning. Remove lime sediments with vinegar.

Whipping/mixing whisks and kneading hook
C1, C2, C3 Immediately after use, wash the attachments in hot water with a detergent and let dry out.

Blender F
Immediately after use, wash the attachments in hot water with a detergent and let dry out. Knife cleaning procedure: pour about 0.5 l of clear water in the container, switch on the appliance and remove the impurities by several pulses. In the case of a larger amount of impurities, repeat the procedure several times, or pour 1 litre of water, add a small amount of detergent and switch on the blender for 1 minute. For easier cleaning, take the knife F3 from the blender base F2 according to Fig. 6.

Sealing replacement procedure
Proceed according to Fig. 6. If the sealing F4 is worn or damaged, replace it with
a new one (of identical type ETA 102800260).

More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by professional service! Failure to comply with the instructions of the manufacturer will lead to the expiration of the right to repair!

STORAGE

Store the properly cleaned appliance including all accessories and attachments at a dry, dustless and safe place, out of reach of children and incapacitated persons.

ENVIRONMENT

If the dimensions allow, there are marks of materials used for the production of packing, components and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electrical
or electronic products must not be disposed of together with municipal waste. For proper disposal, hand them over at the special collection places where they will be accepted free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Ask for more details at the local authority or at a collection site. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. If the appliance is to be put out of operation, after disconnecting it from power supply we recommend its cutoff and in this way it will not be possible to use the appliance again.

TECHNICAL DATA

• Voltage (V)
• Input power (W)
• Weight (kg) (without accessories) approx. Volume of the stainless steel bowl (l) Volume of the blender jug (l)
• The protection class of the appliance
• Input in off mode is
• Noise level:
• Shown on the type label of the appliance Shown on the type label of the appliance ca 8,5
  • 5,5
  • 1,5
  • I.
  • < 0,50 W
• Acoustic noise level of 82 dB(A) re 1pW

The manufacturer reserves the right to change the technical specifications and accessories for the respective models. Product images are for illustrative purposes only.

WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE INSTRUCTIONS MANUAL:

HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS.
TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, ARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.
CAUTION : DO NOT PUT FINGERS OR OTHER ITEMS INSIDE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>