eta 9180 Acorto Espresso User Manual

eta 9180 Acorto Espresso

Product Information

Specifications

• Model: ACORTO
• Manufacture Date: 31/10/2023
• Dimensions: 21.5 x 34 x 45.5 inches
• Water Tank Capacity: 120 ml
• Power Cord Length: 1.3 meters

Product Usage Instructions

Safety Warning

• General Provisions: Place the appliance on a flat and stable surface, away from heat sources, flammable objects, and wet surfaces.
• Power Cord: Ensure the power cord is not damaged and is plugged into a suitable power outlet.

Description of the Appliance
Refer to the table in section B) CONTROL for a detailed description of the buttons and their functions.

Instructions for Use

• A) Installation and Settings

1.  **Location:** Position the coffee machine on a flat surface near a socket with a minimum distance of 15 cm from any wall.
2.  **Filling the Tank with Water:** Remove water tank C, fill it with water (preferably lukewarm), and put it back ensuring it does not exceed the MAX mark. Do not fill water if the tank is in the coffee machine device.

Frequently Asked Questions (FAQ)

• How do I clean the appliance?
  To clean the appliance, wash tanks C and D in warm water with a suitable detergent, rinse with clean water, and allow them to dry.

• What should I do if the appliance malfunctions?
  If the appliance malfunctions, refer to the troubleshooting guide in the user manual or contact customer support for assistance.

INSTRUCTIONS FOR USE
Dear customer, thank you for purchasing our product. Keep this instruction for use and cash receipt (if possible, including the package and its interior) for further reference.

SAFETY WARNING

GENERAL PROVISIONS:

• Before the first use, read the instructions for use carefully, look at the picture and store the instructions for use for the future. Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
• Check whether the data on the type label correspond with the voltage in your socket. The power cord plug has to be connected to the properly connected and grounded socket according to the national standard.
• This appliance may not be used by children. Keep the appliance and its cord out of the reach of children.
• The device may be used by persons with reduced physical or mental abilities or lack of experience and knowledge only if they are under supervision or they have been instructed about using the appliance safely and understand the potential dangers.
• Children must not play with the appliance.
• Before replacing accessories or accessible parts that are moving during operation, before assembly and disassembly, before you fill the water tank or remove the coffee dregs, before cleaning and maintenance, before transfer, if the appliance is left unsupervised, or if you finish using it, make sure to switch OFF the appliance and unplug it from the mains by pulling the plug from the socket!
• Before you remove any accessible parts, before maintenance and handling, allow the appliance and any parts thereof to cool down.
• CAUTION – Do not use the appliance with a program, time switch or any other part that turns the appliance on automatically as there is a risk of fire if the appliance is not covered or placed properly.
• WARNING – Some parts of this product may become very hot and cause burns. During operation, the appliance produces hot water and hot steam under pressure. Special attention must be paid to the presence of children and handicapped people.
• Never immerse the appliance or its cord (or parts thereof) in water. Avoid spilling the cord.
• For hygienic reasons, clean the milk tank by rinsing it after each use. After it has cooled down, remove, and disassemble the milk container and then carry out complete maintenance on all parts.
• When the appliance is in operation, prevent pets, plants or insects to get in contact with it.
• Do not plug the fork of the supply cord into the power outlet and do not unplug the cord with wet hands or by pulling by the supply cord!
• Prevent injuries when handling (e.g. by hot water, steam).
• Never transfer the appliance when there is water in the tank! Water might leak into the internal components.
• Never leave the appliance unattended when it is connected to the mains and keep an eye on it the whole time you are making your espresso!
• Use the appliance only if all the parts are mounted properly.
• Clean the appliance and its accessories regularly! Proceed as per chap. IV. MAINTENANCE.
• When transferring the appliance, take it by the outer casing only.
• Leave a space of at least 15mm from all sides of the appliance to ensure proper circulation of air.
• Cover D4 and removable rear part D2 of the milk container D have built-in magnets.
• Should any of them come loose, keep it out of the reach of children and incapacitated persons. Should anyone swallow or inhale the magnets, immediately seek medical help.
• Magnetic stripe cards, magnetic storage media or other devices which could be affected by the magnetic field should be kept at a safe distance from the appliance (especially away from components D2 and D4).
• Do not expose the appliance to temperatures under 4°C – if residual water froze in the internal components, it could damage the appliance.
• Do not place any objects, including cups, onto the appliance (especially on the top of it).
• Use this appliance only for the purpose for which it was designed as specified in this user‘s manual. Never use the appliance for any other purpose.
• The producer is not responsible for damage caused by improper use of the appliance (e.g. burning, scalding, fire) and its guarantee for the appliance does not apply to situations when the safety warnings above are not complied with.

USE OF THE APPLIANCE:

• The appliance is intended for home use and similar (in shops, offices and similar workplaces, guests in hotels, motels and other residential environments, in facilities providing accommodation with breakfast, in agriculture). It is not intended for commercial use!
• If you are not going to use the appliance for a longer time, empty the water tank! If you do not brew coffee frequently, replace the water in the water tank regularly (preferably every day) so as to keep it fresh at all times.
• Use cold (lukewarm) clean water only! Never use hot water or other liquids – they could damage the appliance.
• The coffee grinder is designed to grind coffee beans only – do not use it to grind any other ingredients or to grind caramelized or sugar-coated whole bean coffee, unprocessed coffee (green, unroasted coffee beans) or mixtures or to re grind ground coffee.
• Do not use the hot water feature longer than it takes to use up the capacity of one water tank.
• To set the grind size, the grinder must be active.
• Descale the appliance regularly. You will be prompted to descal your coffee machine by message on display B15 (see section IV. MAINTENANCE).
• When the bean coffee container has been filled and the grind size set, close the container tightly! Make sure that no foreign objects or hair enter into the container.
• Use the appliance in the working position only at flat and stable places with no risk of turning over and in sufficient distance from heat sources (e.g. heater, stove, cooker, oven, grill), flammable objects (e.g. curtains, drapes, etc.) and wet surfaces (e.g. sinks, wash basins, etc.).
• Do not place the appliance near objects or under objects which could get damaged by steam, e.g. walls, kitchen cupboards, sideboards, paintings, or curtains. Leaking steam could damage them.
• Do not use the appliance in an environment saturated with explosive or flammable steams.
• Before switching on the appliance ensure that the water level does not exceed the MAX mark.

POWER CORD:

• If the power cord of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician or a similarly qualified person so as to prevent dangerous situations.
• Never use the appliance if its power cord or plug is damaged, if it does not work properly, if it fell down and was damaged or if it fell to water. In this case take the appliance to a special service to check its safety and proper function.
• Never put the power cord on hot surfaces or do not let it hang over the edge of a table or a work top. Plugging or pulling the power cord e.g. by children can result in tilting over or drawing the appliance down and serious injury!
• The power cord must not be damaged with sharp or hot objects, open fire, it must not be sunk into water or bent over sharp edges.

DESCRIPTION OF THE APPLIANCE

• A – The machine body
  • A1 – height-adjustable spout
  • A2 – opening for connection of the milk container
  • A3 – hinged cover
  • A4 – grind size knob
  • A5 – bean coffee container (200 g)
  • A6 – container cover
  • A7 – tank gasket
  • A8 – ground coffee opening
  • A9 – ground coffee opening lid
  • A10 – Power cable
• B – Control panel
  • B1 – ON/OFF button
  • B2 – Espresso button
  • B3 – Coffee button
  • B4 – Americano button
  • B5 – Cappuccino button
  • B6 – Latte button
  • B7 – Macchiato button
  • B8 – More button
  • B9 – menu item selection button
  • B10 – OK button
  • B11 – Back button
  • B12 – Rinsing button
  • B13 – Menu button
  • B14 – My Coffee button
  • B15 – display
• C – Water tank (1300 ml)
  • C1 – tank lid
• D – Milk tank (250 ml)
  • D1 – lid
  • D2 – removable rear part
  • D3 – milk froth outlet
  • D4 – cover
  • D5 – detachable connection pipe
• E – Coffee dregs container
• F – Drip tray
  • F1 – drip grille
  • F2 – floater
  • F3 –drip tray cover
• G – Coffee beans spoon

Note
For detailed description of the buttons and their functions please refer to the table in section “B) CONTROL”.

INSTRUCTIONS FOR USE

Before first use, remove any packaging and protective material (including any protective film) from the appliance and accessories. Wash tanks C and D in warm water with a suitable detergent, rinse with clean water and allow to dry.

INSTALLATION AND SETTINGS

1. Location
   Place the coffee machine onto a flat and stable surface, near a socket.
   Keep a minimum distance of 15 cm from any wall at all sides.

2. Filling the tank with water
   Remove water tank C, fill it with water (preferably lukewarm) and put it back (observe MAX mark). Do not fill water if the tank is in coffee machine device!

3. Filling milk
   Fill tank D with milk (observe MAX mark). Then connect container D to the coffee machine using pipe D5.
   Notes

   • If possible, use only fresh whole milk.
   • It is also possible to use alternative types of milk (soy, almond, etc.) with a label “Barista“.

4. Removing operational components
   When you are removing parts that are used frequently when the coffee machine is in operation (e.g. when you are removing the coffee dregs, pouring away drip water, during maintenance, etc.), proceed as indicated in Fig. 1. Proceed in reverse order to put the components back.

5. Refilling coffee beans
   Remove container lid A6 and fill coffee beans to container A5. Then put on the lid again. Make sure that the tank cover is always locked into place. Proper position of the cover protects, besides other things, the coffee beans from losing their aroma. However, only fill the tank with such a quantity of beans which is necessary approximately for one day.

6. Putting into operation
   Connect supply cable A10 to electric mains. Press and hold button B1 for approx. 3 seconds to switch on the coffee machine. After initial switching on, set the language first (see section “E) OTHER FUNCTIONS AND SETTINGS OPTIONS OF THE COFFEE MACHINE – 5) LANGUAGE” for detailed description ), water hardness (see “E) OTHER FUNCTIONS AND SETTING OPTIONS OF THE COFFEE MACHINE –

4. Water hardness ” for detailed description) and make filter setting (for installation of the BRITA AquaAroma Crema water filter see section “PRESET COFFEE MACHINE MAINTENANCE PROGRAMS – 4) Filter maintenance and installation”).The coffee machine menu will prompt you on the sequence of individual steps. Then the interior system of the coffee machine will be filled with water, heated up and automatically rinsed (the course of these operations will be displayed on B15). Now the device is ready for use (graphical information and text messages “Select beverage” and “Ready” will be displayed on B15.

7. Setting the grind size
   Caution When setting the grind size, make sure that the grinder is in operation (i.e. grinding) – never adjust the grind size while the grinder is idle!
   You can adjust the grind size with the grind size knob A4. Turn the knob to the required grind size. There are 9 grinding levels on choice (1 = the finest grinding, 9 = the most coarse grinding). If you want your coffee to run down faster, e.g. because its taste is too strong for you, set the coarser level of grinding. On the contrary, if you want the coffee to run down more slowly (so as to obtain richer aroma and a stronger taste), set a finer level. However, if you set a fine grind size, your coffee might run down very slowly. The new settings will only become evident when you are making a third cup after the change.

8. Rinsing the coffee maker
   The device has a rinsing function that can be enabled by pressing button B12. It is recommended to activate this function several times consecutively if the device has not been used for a long time or after the initial putting into operation.
   Note When flushing out the coffee machine, collect the water into the drip tray F or into a suitable cup. Empty the drip tray regularly.

   • Automatic rinsing of the coffee maker
     The coffee machine has the automatic rinsing function after each switching on, i.e. the interior system will be filled with water, and then heated up. Then the automatic rinsing will be carried out. The course of rinsing will be displayed on B15. This function helps maintaining the device in good condition.

OPERATION

Notes

• every time you press the button, you will hear a signal sound. Signal tones can be disabled (see section “E) OTHER FUNCTIONS AND SETTING OPTIONS OF THE COFFEE MACHINE – 6) Sound”).
• Press B11 to cancel drink preparation.
• the weight of the ground coffee is influenced also by the programmed fineness/coarseness of grinding.
• During use of the device, tightly follow the instructions displayed on B15.

INDIVIDUAL SETTING
The coffee machine offers 3 setting options for each individual drink: one- time setting change, permanent setting change, preferred coffee function (using button My Coffee B14).

Individual setting options

Drink| Coffee temp (available only for the permanent setting change)| Strength (not available for “Use ground coffee function” )| Coffee volume (ml)| Foam time (s)| Wait time (s)| Water volume (ml)
Espresso| Low/Medium/High| 1-5| 15-200| –| –|
Coffee| Low/Medium/High| 1-5| 15-200| –| –|
Americano| Low/Medium/High| 1-5| 15-200| –| –| 15-240
Cappuccino| Low/Medium/High| 1-5| 15-200| 5-50| –|
Latte| Low/Medium/High| 1-5| 15-200| 5-50| –|
Macchiato| Low/Medium/High| 1-5| 15-200| 5-50| 1-30|
Flat white| Low/Medium/High| 1-5| 15-200| 5-50| –|
Lungo| Low/Medium/High| 1-5| 15-200| –| –|
Ristretto| Low/Medium/High| 1-5| 15-200| –| –|
Black coffee| Low/Medium/High| 1-5| 15-200| –| –| 15-240
Double espresso| Low/Medium/High| 1-5| 15-200| –| –|
Double coffee| Low/Medium/High| 1-5| 15-200| –| –|
Travel mug| Low/Medium/High| 1-5| 15-200| –| –|
Milk foam| –| –| –| 5-50| –|
Hot water| Low/Medium/High| –| –| –| –| 15-240

• 1st mode: One-time setting change
  One-time setting change can be made during individual phases of the coffee preparation by pressing buttons B9. Setting options for individual drinks are shown table “Individual setting options”.
  NOTE
  In this event, the relevant change WILL NOT BE STORED in the memory of the coffee machine!

• 2nd mode: Permanent setting change
  This mode allows the widest range of changes. The options for individual drinks are shown in table “Individual setting options”. These changes will be stored in the memory.
  Procedure:

  • Press button B13 Menu in the stand-by mode.
  • Select an option from “Beverage” using buttons B9 and press B10 OK to confirm.
  • Using buttons B9, select a drink you want to change and press B10 OK to confirm.
  • Use buttons B9 to make relevant changes. Press B10 OK to go to the next step. Change options for individual drinks are shown in table “Individual setting options”.
  • After completion of all steps, “Saved” will be displayed on B15 and the values will be stored in the coffee machine memory.
    NOTE
    Permanent change can be cancelled by activation of factory settings (see section “E) OTHER FUNCTIONS AND SETTING OPTIONS OF THE COFFEE MACHINE – 3) Factory settings”).

• 3rd mode: Preferred coffee function (using button B14 My Coffee)
  In this way, you can store up to 4 preferred coffee types (My coffee 1, My coffee 2, My coffee 3 and My coffee 4).
  Preferred coffee setting procedure:

  • Press button B14 My Coffee in the stand-by mode.

  • Choose one of the items (My coffee 1 / My coffee 2 / My coffee 3 / My coffee 4) in which you want to store your coffee data using buttons B9.

  • Then choose one of the required drinks from the selection.

  • As soon as the preparation of the drinks starts, you can change settings. For changing options of individual drinks refer to table “Individual setting options”.

  • The changes you have made will be stored.
    Example of using the Preferred coffee function:
    The preferred coffee in item “My coffee 2” (Espresso, Strength 4, Coffee volume 55 ml) has been set using the procedure above.

  • Press button My Coffee B14 in the stand-by mode.

  • Select item “My coffee 2” using buttons B9.

  • Then press button Espresso B2.

  • The coffee machine will prepare Espresso (Espresso, Strength 4, Coffee volume 55 ml).

NOTE

• You must remember which drink has been stored in the relevant Preferred coffee item.
• The preferred coffee memory can be reset by activation of factory settings (see sectio “E) OTHER FUNCTIONS AND SETTING OPTIONS OF THE COFFEE MACHINE – 3) Factory settings”).

BRIEF INSTRUCTIONS FOR USE

1. Switch on the coffee machine and wait until it has been heated up, interior system filled with water and automatic rinsing process completed.
2. Then the coffee machine will go to standby mode.
3. If you are going to prepare a coffee with frothed milk (e.g.: cappuccino, latte etc.), fill container D with milk and connect it to the coffee machine.
4. Place a cup which is appropriate to the size of the coffee you have selected under the coffee spout A1. Adjust the coffee spout height to the cup size.
5. Select the required drink (see section “B) CONTROL”).
6. Wait until your drink is ready.
7. When the coffee making process is finished, the coffee machine will switch to the stand-by mode. If you were preparing milk froth, you bill be prompted to rinse the frothing unit.
   Cup preheat
   For an optimum coffee making process and better taste of your coffee, we recommend that you preheat your cup by filling it with hot water first. After the cup has been preheated, pour the water away.

E) OTHER FUNCTIONS AND SETTING OPTIONS OF THE COFFEE MACHINE

1. Automatic switching off
   The coffee machine has automatic switch off function. Factory set switching off time: after 30 minutes of inactivity.
   This value can be changed by the following sequence:

2. Press button B13 Menu.

3. Press buttons B9 to open “System”.

4. Press button B10 OK to confirm.

5. Press buttons B9 to open “Auto off”.

6. Set the required time of inactivity for automatic switching off (15 Min / 30 Min / 1 H / 2 H / 3 H / 4 H / 5 H / 6 H / 7 H/ 8 H).

7. Press button B10 OK to confirm the selection. Message “Saved” will be displayed.

8. Press button B11 to exit the menu.

9. ECO program
   This program allows power saving in coffee machine operation. If activated, the coffee machine will not be heated, when in stand-by mode. If the temperature of the internal system falls below specific value, the system will be always heated up to the required temperature before preparation of any drink.
   ECO program can be activated/deactivated as follows:

10. Press button B13 Menu.

11. Press buttons B9 to open “System”.

12. Press button B10 OK to confirm.

13. Press buttons B9 to select item “ECO mode”.

14. Press button B10 OK to confirm.

15. Press buttons B6 to select “Close” (for deactivation) or “Open” (for activation).

16. Press button B10 OK to confirm the selection. Message “Saved” will be displayed.

17. Press button B11 to exit the menu.

18. Factory reset
    Observe the following procedure to reset the device to factory settings:

19. Press button B13 Menu.

20. Press buttons B9 to open “System”.

21. Press button B10 OK to confirm.

22. Press buttons B9 to select item “Factory reset”.

23. Press button B10 OK to confirm.

24. Press button B10 OK to confirm factory settings. (or press B11 to cancel the selection).

25. Then the coffee machine will be switched off. After next switching on the device by pressing B1, factory settings will be restored.
    NOTE By activation of factory settings of the coffee machine, all prior individual settings will be reset!

26. Water hardness
    You will be prompted to set water hardness already at the initial switching on the coffee machine.
    The setting can be modified any time. Procedure:

27. Press button B13 Menu.

28. Press buttons B9 to open “System”.

29. Press button B10 OK to confirm.

30. Press buttons B9 to select item “Water hardness”.

31. Press button B10 OK to confirm.

32. Press buttons B9 to set the relevant level (see “Water hardness setting table”).

33. Press button B10 OK to confirm. Message “Saved” will be displayed.

34. Press button B11 to exit the menu.

35. Language
    You will be prompted to set the language already at the initial switching on the coffee machine.
    The language can be changed any time. Use the following procedure:

36. Press button B13 Menu.

37. Press buttons B9 to open “System”.

38. Press button B10 OK to confirm.

39. Press buttons B9 to select item “Language”.

40. Press button B10 OK to confirm.

41. Press buttons B9 to set the relevant language (Czech / German / English / Simplified Chinese. / Traditional Chinese / Russian / Spanish / Italian).

42. Press B10 OK to confirm. Message “Saved” will be displayed.

43. Press B11 to exit the menu.

44. Keyboard sound
    Signal tones can be switched on/off any time, using the following procedure:

45. Press button B13 Menu.

46. Press buttons B9 to open “System”.

47. Press button B10 OK to confirm.

48. Press buttons B9 to select item “Keyboard sound”.

49. Press button B10 OK to confirm.

50. Press buttons B9 to select item “On” / “Off”, as required.

51. Press B10 OK to confirm. Message “Saved” will be displayed.

52. Press B11 to exit the menu.

53. Empty water circuit
    Observe the following procedure to drain water from the coffee maker:

54. Press button B13 Menu.

55. Press buttons B9 to open “System”.

56. Press button B10 OK to confirm.

57. Press buttons B9 to select item”Empty water circuit”.

58. Press button B10 OK to confirm.

59. Message “Please remove water tank” will be shown on display B15. Carry out this action.

60. Message “Start to empty water circuit” will be displayed on B15.

61. Press button B10 OK to confirm.

62. If the milk container D has not been inserted, message “Instal milk carafe” will be shown on display B15. Carry out this action.

63. Then draining water will start automatically. Message “Emptying” will be displayed.

64. After completion of the draining process, the coffee machine will be switched off automatically.

MAINTENANCE

Unplug the appliance from power supply by taking the fork of the power cord out of the socket (except for operations which require the coffee machine to remain switched on)! Clean the appliance only when it is cooled down! Do not use rough and aggressive detergents (e.g. sharp objects, scrapers, diluting agents or other solvents)! Components E, F, F3 and G can be washed in dish washer (washing program maximum 50 °C).

IMPORTANT
Check and clean all parts regularly, thus avoiding mould growth on the rests of coffee and milk!

Water tank C
We recommend that you clean the tank thoroughly and regularly (about once a week). Use regular washing-up liquid and then rinse the tank with clean water. So as to prevent build-up of scale deposits, we recommend that you also rinse the tank under running water once a day.

Milk tank D
When milk frothing has been terminated, all parts must be cleaned thoroughly! Disassembling procedure see fig. 1. Wash them using standard dishwashing agent, then rise in clean water. Allow to dry.

Remarks

• Request for rinsing the frothing system will be displayed on B15 after every milk frothing process (see section “B) CONTROL”).
• The coffee machine has also a program for thorough rinsing of the frothing unit (see section “PRESET COFFEE MACHINE MAINTENANCE PROGRAMS – 1) Milk systen cleaning”).

Coffee dregs container E and drip tray F
Disassemble the individual coffee machine components as per Fig. 1. Wash them with regular washing-up liquid, rinse them under running water and let them dry. The device informs on required maintenance by messages displayed on B15.

PRESET COFFEE MACHINE PROGRAMS

1. Cleaning of the frothing system
   This program is intended for thorough cleaning of the frothing unit, if you prepare a coffee with frothed milk in the coffee machine (cappuccino, latte etc.). We recommend using this program at least 2-4 times a month (depending on how often milk froth was prepared in the device). Use clean water for this program (with adding a little vinegar, as the case may be).
   Procedure:

2. Press button B13 to open the menu.

3. Press buttons B9 to select item “Maintenance”.

4. Press button B10 OK to confirm.

5. Press buttons B9 to select item “Milk system cleaning”.

6. Press button B10 OK to confirm.

7. Message “Please mix original cleaning agent with water in milk carafe and instal milk carafe” will be displayed on B15. Fill water to container D (as the case may be, with added vinegar). Place a suitable vessel (cup) below frothed milk outlet D3.

8. Press button B10 to confirm the start (“Start”).

9. Wait until message “Clean milk carafe and fill in fresh water” is displayed on B15. Then rinse the vessel and add clean water.

10. Press button B10 to go to the next step “Next”.

11. When the program has been finished, message “Completed”. will be displayed on B15.

12. Thoroughly rinse container D.

13. Brewer cleaning
    This program is intended for thorough cleaning of the steaming unit. Clean the steaming unit regularly, after preparation of approx. 300 cups of coffee (the quantity of coffee cups can be identified in the drink counter, see coffee machine menu – section “B) CONTROL”). Use suitable cleaning tabs for this purpose.
    Procedure:

14. Press button B13 to open the menu.

15. Press buttons B9 to select item “Maintenance”.

16. Press button B10 OK to confirm.

17. Press buttons B9 to select item “Brewer cleaning”.

18. Press button B10 OK to confirm.

19. Message “Please use original cleaning product” will be displayed on B15. Fill clean water to container C. Place a suitable vessel (cup) below outlet A1. Empty this vessel during the cleaning process as required.

20. Press button B10 OK to confirm and press “Next” to go to the next step.

21. Message “Empty drip tray and grounds container” will be displayed on B15 Empty vessel E and drip tray F.

22. Press button B10 OK to go to the next step “Next”.

23. After a while, message “Add the cleaning tablet” will be displayed. Insert the table into opening A8.

24. Press button B10 OK to go to the next step “Next”.

25. Message “Completed” will be shown on display B15.

26. Thoroughly rinse vessel C to remove all remainders of the cleaning agent.

27. Descaling
    You will be prompted to carry out descaling of your coffee machine on display B15. The intervals of descaling cycles depend on set water hardness. Use commercial-grade descaling liquids intended for coffee and espresso makers.
    NOTE If you use water filter, remove it before descaling.
    Procedure:

28. Press button B13 to open the menu.

29. Press buttons B9 to select item “Maintenance”.

30. Press button B10 OK to confirm.

31. Press buttons B9 to select item “Descaling”.

32. Press button B10 OK to confirm.

33. Message “Please use original cleaning product” will be displayed on B15. Fill containers C and D with the cleaning solution. Place a suitable vessel below outlets A1 and D3 (cup). Empty this vessel during the descaling process as required.

34. Press button B10 OK to go to the next step “Next”.

35. Message “Empty drip tray and grounds container” will be displayed on B15. Empty vessel E and drip tray F.

36. Message “Add descaling agent into the water tank and fill the water tank with fresh water to the Max level mark” will be displayed on B15. Be sure containers C and D are filled with the cleaning solution.

37. Press button B10 OK to proceed (“Start”).

38. Wait until message “Empty drip tray and grouds container” is displayed on B15. Empty vessel E and drip tray F.

39. Wait until message “Clean the water tank and fill the water tank with fresh water to the Max level mark” is displayed on B15. Rinse container C and fill it with clean water.

40. Press button B10 OK to go to the next step “Next”.

41. Wait until message “Empty drip tray and grouds container” is displayed on B15. Empty vessel E and drip tray F.

42. When the program has been finished, message “Completed” will be displayed on B15.

43. Thoroughly rinse container D to remove all remainders of the cleaning agent.

44. Install/change filter
    You can install water filter BRITA AquaAroma Crema into the device. The filter will be inserted directly to water container C (on the bottom valve).
    Procedure:

45. Press button B13 to open the menu.

46. Press buttons B9 to select item “Maintenance”.

47. Press button B10 OK to confirm.

48. Press buttons B9 to select item “Install/change filter”.

49. Press button B10 OK to confirm.

50. Message “Install filter?” will be displayed on B15. Fit the filter in place.

51. Press button B10 OK (“Yes”) to confirm the filter has been fitted.

52. Message “Please install filter in the water tank” will be displayed on B15. Be sure the filter has been inserted correctly.

53. Press button B10 OK to go to the next step “Next”.

54. Message “Rinsing” will be displayed on B15 and filter rinsing process will be completed.

55. When rinsing has been finished, message “Completed” will be displayed on B15.
    NOTE Check the filter regularly and replace, as required.

Expert service must do the large maintenance or to intervene into inside parts of the appliance! If you are unable to fix the problem, or if you need any further information about the appliance or service centres, please contact your distributor.

TROUBLESHOOTING

coffee machine with hot water in three flush cycles.
The brewing unit is too cold.
The coffee is flowing very slowly, or just trickling.| The coffee is too finely ground.| Set a coarser grinding level.
The first cup is of poor quality.| The grinder did not supply enough ground coffee to the brewing unit during the first grinding.| Pour the first cup away. The following cups will be of a better quality.
The coffee has no foam (crema).| The coffee beans are not fresh or the coffee beans are of a low quality.| Change your coffee brand or use fresh coffee.
The grind size set produces a too coarse grind.| Set a finer grind size
Touch buttons are not sensitive.| Button pressed incorrectly.| Always press the buttons from the front side of the panel, using the whole finger pad.
Fingers might be greasy or dirty.| Wash your fingers.
Milk frothing unit does not produce quality milk foam or liquid milk is flowing from the outlet.| The milk has not been cooled down sufficiently or an unsuitable type of milk has been used| Use fresh whole milk or milk types with ‟Barista“ designation. Also, the milk should be cooled to 5-10 °C.
---|---|---
Dirt in the milk frothing adapter.| Check the milk frothing unit and clean it thoroughly (see section IV. MAINTENANCE ).

ENVIRONMENT
Printed signs of materials used for manufacture, packing, components and accessories, as well as their recycling, are on all the pieces if their dimensions enable it. The symbols on the product or in the accompanying documentation mean that the used electric or electronic products must not be disposed together with municipal wastes. Please, hand them over to the collection points designed for their correct disposal, where they will be accepted free of charge. By correct disposal of this product you can help to preserve valuable natural resources and help to prevent possible negative impacts to the environment and to human health, which could be the results of incorrect waste disposal. For further details ask the municipal authorities or the nearest collecting point. Penalties can be charged for incorrect disposal of such wastes, according to national regulations. If the appliance is to be put out of operation definitely, we recommend cutting off the feeder cable, to disable its use.

TECHNICAL DATA

• Voltage (V): shown on the type label of the appliance
• Absorbed power (W): shown on the type label of the appliance
• Max. volume (I): 1.3
• Milk container volume. (I): 0.25
• Weight (kg) approximately: 9.6
• Protection class of the appliance: I.
• Size, (cm): 21.5 x 34 x 45.5

Input in off mode is < 0.50 W.

The manufacturer reserves the right to change the technical specifications and accessories for the respective models.

WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE INSTRUCTIONS MANUAL:
HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS.

References

• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• ElektroEko – Odbiór odpadów elektro
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>