eta 1028 Glass Blender Instruction Manual

Glass blender
INSTRUCTIONS FOR USE

1028 Glass Blender

Glass blender
eta 102899002
USER`S MANUAL
Dear customer, thank you for purchasing our product. Please read the operating instructions carefully before putting the appliance into operation and keep these instructions including the warranty, the receipt and, if possible, the box with the internal packing.

SAFETY NOTICE

• Consider the instructions in the user`s manual as a part of the appliance and provide it to other users of the appliance.

• This appliance must not be used by children. Keep the device out of reach of children. The device may be used by persons with reduced physical or mental abilities or lack of experience and knowledge only if they are under supervision or they have been instructed about using the appliance safely and understand the potential dangers. Children must not play with the appliance.

• Before replacing accessories or accessible parts, which move during operation, before assembly and disassembly, before cleaning or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord from the power socket!

• If leaving the extra attachment unsupervised, always switch off and disconnect the drive unit from the mains.

• Do not leave the appliance in operation without supervision and supervise it for the entire time that food is being prepared!

• Never use the appliance, if it is not functioning correctly or if it has fallen on the fl oor and been damaged or if it has fallen into water.

• Be careful when pouring hot liquid into the mixer because it may spurt out of the appliance because of sudden boil.

• Be careful when handling the blender, the knife is very sharp!

• When assembling the extra attachment, follow the instructions for use carefully. In order to ensure proper functioning, any other way of assembling the extra attachment is not permissible!

• Maximum time of processing is 2 min. After that, keep the break for approx. 3 min necessary for the motor unit to cool off.

• The appliance is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!

• Every time before the propulsion unit is switched on, the container needs to be attached properly and the lid or the pusher needs to be placed appropriately so as to close the container. The safety plug needs to be inserted in the lid.

• Do not turn on the appliance without any ingredients inside! ­

• The container is not designed for keeping and storing food. Put the food in another container suitable for storage after mixing.

• Before preparation, remove possible packages from food (e.g. paper, PE bag, etc.) ­

• If the processed ingredients start to stick on the accessory (e.g. the knife, blender glass or the lid), turn the appliance off and clean carefully with a spatula. ­

• When handling the appliance, use the handle. ­

• Do not put more liquid than marked on the dish (MAX mark) and always use the lid when mixing or blending liquids. ­

• WARNING: When the blender is in the state of idle operation, e.g. The blade fails to touch the foods, unplug the unit until the foods have been relaxed. ­

• When mixing or blending liquids, never put in bigger amount than specified on the bowl.

• Do not process foods with a temperature over approx. 80 °C (176 °F). When blending hot liquids, remove plug F5 from the blender lid.

• Long hair, loose clothes or accessories and jewellery can get caught by the rotating parts of the extra attachment. Make sure that your hair, clothes and accessories do not get into dangerous vicinity to the rotating parts!

• Never insert your fingers into the filling opening and do not use a fork, knife, spatula, spoon, etc.

• Due to safety it is not possible to change the attachments while the drive unit is in operation.

• Never remove the lid F1 from the attachment until the cutting knife has completely stopped.

• Before removing the lid from the bowl or the extra attachment from the drive unit, allow the rotating parts to stop completely.

• Never use the pusher F7 individually without the lid F1.

• Do not insert accessories into any body cavities.

• Use the extra attachment only with the drive unit / food processor designed for this type.
  Using another type of drive unit / food processor can present a risk for the operator.

• Do not process frozen food.

• Do not turn on the appliance without any ingredients inside!

• If the funnel is empty, do not leave the extra attachment running.

• The appliance do not use without the mounted lid.

• Use this appliance only for the purpose for which it was designed as specifi ed in this user‘s manual. Never use the appliance for any other purpose.

• WARNING: There is a risk of injury in case of incorrect use (not in accordance with the manual) of the appliance.

• All text in other languages and pictures shown on the packaging, or the product itself, are translated and explained at the end of this language mutation.

• Product images are for illustrative purposes only.

• The manufacturer takes no responsibility for damages and injuries caused by the incorrect use of supplementary machines and accessories (e.g. ruining of foods, injury, cuts) and takes no responsibility arising from the warranty on the appliance in the case that the above safety notices were not followed.

Attention
Read and follow the safety instructions in the manual to the food processor.

DECRIPTION OF THE APPLIANCE AND ACCESSORIES (Fig. 1)

F – Blender

F1 – Container lid
F2 – Container support
F3 – Knife
F5 – Removable stopper
F4 – Knife sealing| F6 – Glass container
F7 – Pusher
F8 – Lock
F9 – Lock button
---|---

PREPARATION AND ASSEMBLY

Remove all packaging material, remove the accessory. Remove all adhesive foils, stickers or paper from the appliance. We recommend washing the glass container before using it for the first time. The knife section is treated with oil not harmful to health for technological reasons. Therefore first fill in the container with warm water (max. 50 °C) with a small amount of detergent. Then put the container on the food processor, set the maximum rotational speed and run for 1 minute. Then rinse the container with clear water.

Assembly
Assemble the blender and attach it to the blender mount according to Figures 1 a 2.
Instead of the plug for adding liquids F5 you can also insert the pusher F7 in the opening in the lid if you are going to use it. Apply reverse sequence to disassemble the unit and to remove it from the mount – tighten the F2 base properly until the F9 button clicks!

USE

Please consider the following cooking tips as examples and as inspiration. Their purpose is not to be a complete guide, but to demonstrate the possibilities of various food preparation methods. The blender is designed to mix juices, milkshakes, soups, sauces, baby and dietary food, puffy pastry dough, sponge cake dough, to make purée, etc. Remove the lid F1, insert or pour the ingredient into the jug of the blender F6 and return the lid to its place. Do not fill over the line MAX marked on the jug. Put the container on the motor unit, plug into a power socket and put into operation to one of the speed levels appropriate for blending your ingredients. To press larger pieces of ingredients to the knife, use the pusher F7. Always set the speed with regard to the kind and amount of ingredients being processed, and particularly with regard to ripeness of fruit and vegetables.
We recommend that you always switch on the blender to minimum revolutions and then gradually increase the performance as required.
The recommended processing speed is 1 to MAX.

Tips

• When the appliance is in operation, it is only possible to add liquid ingredients (e.g. water, milk, oil, etc.).
• If you are going to process larger amount of food, divide it into batches not to overload the motor unit of the multifunctional head.
• Never use the pusher F7 individually without the lid F1.
• Cut tougher substances into small pieces, otherwise the knife F3 will soon become blunt.
• If you are going to mix ice cubes, their size should not exceed 20 x 20 x 30 mm, otherwise the knife F3 becomes blunt or the motor unit is overloaded.
• Never fill the container with liquids producing foam (for example milk) up to „MAX“ level to prevent overspill. We recommend 1 litre at maximum.
• Soak hard food (such as legumes, soybeans, etc.) in water before further processing.

MAINTENANCE

Before any handling, unplug the power cord from the electric socket. Do not use coarse and aggressive cleaning agents (e.g. sharp objects, scrapers, diluting agents or other solvents). Clean all accessories in hot water with a detergent right after use (do not use a dishwasher). To clean the knife, pour ca. 0.5 l of pure water into the container, switch on the appliance and clean the knife with a few pulses. In case of larger contamination of the knife, repeat the procedure several times, or pour 1 l of water, add a small amount of detergent and switch the blender on for 1 minute. For easier cleaning, take the knife F3 from the blender base F2 according to Fig. 1. Be very careful when cleaning knive! Some ingredients can colour the accessories in some way. But the change does not affect the function of the appliance and it is not a reason for a claim. This colouring usually disappears after some time. Never dry plastic moldings over a heat source (e.g. heater, electric/gas stove). Store the appliance after cleaning at a dry, dustfree and safe place, out of reach of children and incapacitated people. After cleaning, store the appliance in a dry, dustless, safe place, out of reach of children and persons sui juris.

Sealing replacement procedure
Proceed according to Fig.1. If the sealings F4 is worn or damaged, replace it with a new one (of identical type ETA 102800260).
Failure to comply with the instructions of the manufacturer will lead to expiration of the right to guarantee repair!

ENVIRONMENT

If the dimensions allow, there are marks of materials used for production of packing, components and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal, hand them over at the special collection places where they will be accepted free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Ask for more details at the local authority or at a collection site. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations.

TECHNICAL DATA

The manufacturer reserves the right to change the technical specifications and accessories for the respective models.
WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE INSTRUCTIONS MANUAL:

HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS.

| TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, ARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.
---|---
| CAUTION

© DATE 14/6/2023
e.č. 40/2023

References

• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• Serwis Digison
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>