MEEC TOOLS 013514 Ultimate Speed Tyre Compressoral Instruction Manu

013514 Ultimate Speed Tyre Compressor
Instruction Manu
COMPRESSOR

Item no. 013514
6 1/180 1/min

OPERATING INSTRUCTIONS

Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original in­ instructions)
Care for the environment!
Recycle discarded products in accordance with local regulations .

SAFETY INSTRUCTIONS

• Keep the work area clean and tidy. Cluttered work areas put safety at risk.
• Do not expose the product to rain or moisture.
• Do not use the product in damp or wet areas.
• Keep the work area well lit.
• Do not use products where combustible gas or liquids are stored or used. Avoid the risk of electric shock.
• Do not touch earthed objects, such as water pipes, radiators, hot plates, or cookers.
• Keep other people and pets at a safe distance.
• Persons not involved in the work should be kept at a safe distance from the work area and do not allow anyone, especially children, to touch the product or the power cord.
• When not in use, store the product in a dry place, locked up and out of the reach of children.
• Do not overload the product. The work will be safer and better if the product is not overloaded. Wear suitable clothing.
• Do not wear loose-fitting clothing or jewelry. They can get caught in moving parts. Wear non-slip shoes when working outside.
• Wear a hair net if you have long hair. Use personal safety equipment. Wear safety glasses.
• Wear a breathing mask or dust filter mask if the work produces a lot of dust.
• Protect the power cord from damage, and replace a damaged cord immediately.
• Do not pull the power cord to unplug the plug from the PowerPoint.
• Keep the power cord away from heat, oil, and sharp edges. If the power cord or plug get damaged they must be replaced by an authorized electrician.
• Check that the product is clean and free from contamination.
• Follow all the directions for care, maintenance, and storage.
• Check the power cord and plug at regular intervals.
• If the power cord or plug get damaged they must be replaced by an authorized electrician.
• Check any extension cords are at regular intervals. Replace damaged extension cords.
• Keep the handles clean, dry, and free from oil and grease. Always unplug the product when it is not in use, before service and maintenance, and before changing tools. Avoid accidental starting.
• Check that the power switch is in the OFF position before plugging the plug into a PowerPoint.
• Always use the correct type of extension cord. If the product is used outdoors, only use an extension cord approved for outdoor use. Stay alert at all times. Use your common sense.
• Never use the product if you are tired or under the influence of drugs, alcohol or medication.
• Check that the product is undamaged.
• Check before using the product that it is working normally as described in these instructions.
• Check that all moving parts are undamaged, and correctly fitted and that they do not jam.
• Damaged safety devices must be replaced by an authorized service center unless otherwise specified in the instructions.
• A damaged power switch must be replaced by an authorized electrician.
• Do not use the product if it cannot be switched on and off with the power switch.
• Do not use accessories other than those specified in these instructions or recom­ mended by the manufacturer or retailer – the risk of personal injury.
• Repairs should be carried out by qualified personnel.
• The product complies with the applicable safety regulations.
• Repairs may only be carried out by qualified personnel using identical spare parts. Serious personal injury can otherwise occur.
• Risk of hearing impairment.
• Wear ear protection when using the compressor.
• Risk of explosion. Never use the product where flammable material, liquid, or gas (petrol, solvent, gas cylinders, etc.) are stored or used.
• Never switch off the product by pulling out the plug. Always use the ON/OFF power switch or button.
• Always pull out the plug and relieve the pressure in the air tank before moving the product, and before service or repairs.
• Keep the power cord away from heat, oil, and sharp edges.
• Do not carry or pull the product by the power cord or the air hoses.
• The product must only be carried with the handle.
• Check that all the air hoses and air tools to be connected to the compressor are approved for the air pressure produced by the compressor and that they are correctly connected.
• The product is intended to be used in a well-ventilated area an ambient temperature of 5 to 40°C.
• Do not expose the product to water or any other liquid.
• Do not use the product if the air tank is in any way damaged.
• Check that all the air hoses are undamaged and approved for the pressure produced by the compressor.
• Damaged air hoses must be replaced ­ never attempt to repair a damaged air hose.
• Do not move or transport the product when the air tank is pressurized Do not disconnect any air hoses when the air tank is pressurized.
• Do not attempt to tamper with or modify the air tank or any other parts of the product.
• Never point the outlet on the air hose or any tools connected to the hose at people or animals.
• Never attempt to blow clean clothes with compressed air when they are being worn.
• Never poke your fingers or other any objects in the casings on the product.
• The product must only be connected to a 230 V 50/60Hz earthed power point that has a residual current device with a maximum tripping current of 30 mA.
• Always connect the plug to an easily accessible power point so that it can quickly be pulled out in the event of a fault.
• Parts of the product get hot when in use.
• Only touch the handle and the power switch when the product is in use.
• Place the product on an easily accessible, stable, and dry horizontal surface.
• Do not place the product near the edge of a table or bench. Make sure there is adequate ventilation for the product.
• Keep the product at least 1 m away from adjacent walls or any other surface. Position the product so that it cannot move when in use.
• The product must not stand on its own feet when in use.
• Never put the product on, or near hot surfaces.
• The product is not intended to be used by persons (children or adults) with any form of functional disorders, or by persons who do not have sufficient experience or knowledge on how to use it unless they have received instructions concerning the use of the product from someone who is responsible for their safety.
• Keep children under supervision to make sure they do not play with the product.

WARNING!
The air supply to the compressor must be disconnected if an air hose breaks or is damaged. A broken air hose is extremely dangerous and can rotate at great speed, causing injury to persons nearby and blowing foreign objects into the air. Do not attempt to catch the hose, evacuate all onlookers from the risk area, turn off the air supply, switch off the compressor with the ON/OFF switch and then remove the hose from the compressor.

Symbols

The following symbols can be of importance for how you should use your power tool. Make sure you understand the symbols and their significance.

| Read instruction
---|---
| Approved in accordance with
the relevant EU directives.
| Risk of burns
| Warning – live parts.
| Risk of automatic start.
|  Do not open the tap until the
air hose is connected.
| Sound power level
| Wear ear protection.
| Recycle as electrical waste.

TECHNICAL DATA

Always wear ear protection.
The declared values for vibration and noise, which have been measured by a standardized test method, can be used to compare different tools with each other and for a  preliminary assessment of exposure. The measurement values have been determined in accordance with EN 1012-1:2010.
WARNING!
The actual vibration and noise level when using tools may differ from the specified maximum value, depending on how the tool is used and the material. It is, therefore, necessary o determine which safety precautions are required to protect the user, based on an estimate of exposure in actual operating conditions (taking into account all stages f the work cycle, e.g. the time when the tool is switched off and when it is idling, in addition to the start- up time).

DESCRIPTION

The compressor compresses atmospheric air and charges an air tank with compressed air. The compressor motor is switched off automatically by a pressure switch when the maximum permitted pressure in the air tank is achieved. If the pressure switch is not working, or if for any other reason the pressure in the air tank gets too high, the pressure in the tanis relieved by a safety valve. The compressor is oil-free and is only intended for intermittent use. This means that it can only be used for purposes that consume a low volume of air, such as nailers and other small pneumatic tools, filling footballs and other sports equipment, toys, airbrush sprays, and other spray tools.
NOTE:
The compressor is not intended to be used to pump large objects such as pools or inflatable mattresses that require a run time of more than 120 seconds.

1. Power cord
2. Safety valve
3. Pressure gauge
4. Power switch
5. Handle
6. Cord retainer (on each side)
7. Motor casing
8. Air outlet
9. Pressure control knob
10. Air tank
11. Drain valve
    FIG. 1

USE

1. Check that the power switch (4) is in the OFF position.
2. Plug the plug into an earthed power point.
3. Connect the pneumatic tool to be used to the air outlet (8).
4. Switch on the power switch (ON).
5. Set the required working pressure with the pressure control knob (9).

After use
Never disconnect any pneumatic tools before first relieving the pressure in the air tank.

1. Switch off the product and pull out the plug.
2. Relieve the pressure in the air tank and then allow the product to cool.
3. Disconnect the pneumatic tool and wind the cord on the cord retainers (6).

MAINTENANCE

Clean the product with a damp cloth. Use a mild detergent, not a solvent or caustic solution.
WARNING!

• The safety valve should not be tampered with or blocked under any circumstances. Check the air tank for external or internal corrosion at least once a week. The wall thickness of the tank must under no circumstances be less than 2 mm.
• Drain condensation from the air tank at regular intervals by opening the drain valve. Relieve the pressure in the air tank and allow the product to cool, before opening the drain valve.
• If the product is not going to be used for some time pull out the plug, relieve the pressure in the air tank and empty the tank of condensation by opening the drain valve (11).
• Do not use solvents, flammable or toxic liquids to clean the machine and its components. Only clean with a soft, damp cloth. Check that the plug has been unplugged from the PowerPoint.
• Empty the condensate formed in the tank after about 2 hours of use. Activate the connected accessory to empty the tank. Switch off the compressor. Undo the emptying valve 5 under the compressor for two turns. The compressor should be in an upright position. Empty out the water and screw tight the valve.
• If the condensate is not drained the tank can corrode, leading to reduced capacity and putting safety at risk.

IMPORTANT:
Dispose of condensate in accordance with local regulations for contaminants.

TROUBLESHOOTING

The compressor does not start or stop when in use.

• Check that the plug is plugged in.
• Check that the power point is supplied with voltage.
• Check that the ambient temperature is not too low (the compressor is not intended to be used in an ambient temperature less than 5°C).
• Check that the motor is not overheated so that the overheat protection has tripped. If this is the case, allow the compressor motor to cool and then start again.

The compressor starts but does not build up pressure.

• Check that the drain valve is closed.
• Check that all the connected hoses and pneumatic tools are tight.

EU DECLARATION OF CONFORMITY
item number 013514
This declaration of conformity is issued under the sole responsibility of the manufacturer
COMPRESSOR
Conforms to the following directives, regulations, and standards:

55014-2:2015, EN IEC 61000-3- 2019, EN 61000-3-3:2013+A1
EMC 2014/30/EU|
OND 2000/14/EC + 2005/88/EC|
RoHS 2011/65/ 50581:2012| EU + 2015/863  EN
The measured sound power level on an equipment representative for this type:| Guaranteed sound power level:| Conformity assessment procedure according to 2000/14/EC:
---|---|---
94 dB(A)| 97 dB(A)| Annex V

Name and address of the notified body involved:
This product was CE marked in a year:
Intertek Testing & Certification Ltd.
Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL, UK NB0359
Skara 2022-01-25
Mattias Lif BUSINESS AREA MANAGER (Signatory for Jula and authorized to compile the technical documentation.
DOC: EN-SE-NO-PL-DE-FL-FR-NL

JULA AB, BOX 363, SE-532 24 SKARA
2022-01-26
© Jula AB

Documents / Resources

| MEEC TOOLS 013514 Ultimate Speed Tyre Compressor [pdf] Instruction Manual
013514, Ultimate Speed Tyre Compressor, Speed Tyre Compressor, Tyre Compressor, 013514, Compressor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>