AVTech LEDPAR1820LIP 7x10W RGBWAUV Battery PAR LED User Manual

AVTech LEDPAR1820LIP 7x10W RGBWAUV Battery PAR LED

Product Information

Specifications:

• Model: LEDPAR1820 LIP
• Light Source: 7x10W RGBWAUV LEDs
• Battery Powered PAR LED
• DMX Channels: 6, 8, 12
• Control Modes: DMX, Manual, Auto, Slave, Custom, Edit
• Cable Connectors: Male XLR to Female XLR
• Mounting Positions: Ceiling Hanging, Flat Surface
• Safety Measures: Safety cable recommended

Product Usage Instructions

1. Setting Up DMX Address:
   To set the DMX address, navigate to the menu and select the DMX address option. Use the controls to set the desired address.

2.  Cable Connection:
   Ensure proper cabling with a male XLR connector on one end and a female XLR connector on the other end. Refer to the DMX connector configuration for correct wiring.

3. 3. Mounting:
   The LEDPAR1820LIP can be mounted hanging upside-down from a ceiling or placed on a flat surface. Avoid mounting the unit on its side to prevent internal damage. Keep the fixture at least 0.5m away from flammable materials.

4. Safety Measures:
   It is recommended to use the supplied safety cable during installation to prevent accidental damage or injury in case of clamp failure.

FAQ:

• Q: Can the lights be exposed to rain or moisture?
  A: No, it is advised not to expose the lights to rain or moisture to prevent electrical shock or fire risks.

• Q: How should I handle cable grounding?
  A: Avoid grounding the ground to prevent ground loops. Test cables with an ohm meter to ensure proper polarity and no grounding between pins.

User manual
AH042B
TYPHOON PAR 350

• Please read carefully before use
• Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.

7x10W RGBWAUV Battery PAR LED
USER MANUAL

Packaging: Thanks for your purchasing the LEDPAR1820LIP. All the lights have been checked and are in excellent operating condition. Please check the shipping carton first, because there may be damage occurred during the shipment. Then check the lights carefully and be sure that the lights is intact and works normally. In the event damage has been found, spare parts are missing or the lights works abnormally, please contact us for further instructions. And please don’t return the lights to the dealer before contacting us.
Introduction: The LEDPAR1820LIP has three operating modes: DMX mode, Auto mode and Master/Slave mode. And the lights has five DMX modes, including channel 3,channel 6 , channel 8 and channel 12.There are ten built-in Auto programs and you can see ten kinds of shows when you open the Auto mode. Meanwhile, you can edit your desired Auto program in “EDIT” menu. In addition, you can connect several pieces of lights in DMX mode and set one in Auto mode, and the others in Master/Slave mode. And then all the lights in Master/Slave mode will run following the one in Auto mode. Using fog or special effect smoke, you can see better showing effect.

1. Don’t expose the lights to rain or moisture, for the sake of preventing the risk of electrical shock or fire.
2. Don’t look directly at the opening lights all the time, or it may damage your eyes. Warning!

UNPACKING AND PREPARATION

Product Overview

Features

• Light Source: 18*20W, 6 in 1 RGBWAUV LEDs
• Lens: 10°, 15°, 25°, 45°, 60×10°
• Power consumption: 350W
• Voltage: AC 90V -270V, 50/60Hz
• Run Mode: DMX 512 /Master Slave/Auto Run
• 10 internal programs and 11 customerize programs
• 4 different dimming curve
• 11 kinds of color temperature white
• Maximum 66 ID setng for easy separate control
• DMX Channels: 3, 6, 8 & 120CH
• Built-in Effect: color mixing, variable color chasing, strobing and fading.
• TFT displayer with four buttons
• Material: Aluminum body
• IP65
• Temperature: -30℃~45℃
• Dimension: 354 X 159 X 309 mm
• N.W: 8.5 KG
• G.W: 10 KG

Programme Menu

Mechanical Specification

CABLE CONNECTORS

Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
DMX connector configuration

caution:Do not allow contact between the ground and the fixture’s chassis ground. Grounding the ground can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to verify positive pole and to make sure the pins are not grounded or shorted to the shield or each other.
3-PIN TO 5-PIN CONVERSION CHART
Note! If you use a controller with a 5 pin DMX output connector, you need to use a 5 pin to 3 pin adapter. The chart below details a proper cable conversion:
3-PIN TO 5-PIN CONVERSION CHART

Displayer introduction

1. DMX means the light is in the DMX mode. Similarly, SLAVE means the light is in the SLAVE mode.
2. The color of the point shows the condition of signal transmission. Green represents the good condition, while red represents the signal is interrupted.
3. The item shows the working temperature of the light. When the working temperature exceeds the max temperature, the color of the letters and number will change from white to yellow.
4. This item shows the menu you selected.
5.  This item shows the condition of key lock. “Key lock open” means the key lock is open. And “Key lock off” means the key lock is close.

Mounting

• When installing the unit, the trussing or area of installation must be able to hold 10 times the weight without any deformation. When installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or servicing the unit.
• Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and parodic safety inspection of all installation material and unit. If you lack these qualifications, do not attempt the installation yourself.
• The installation should be checked by a skilled person once a year.

The LEDPAR1820LIP is fully operational in two different mounting positions, hanging upside-down from a ceiling or set on a flat level surface. To avoid internal damage to the unit, never mount the unit on its side as illustrated above. Be sure this fixture is kept at least 0.5m away from any flammable materials (decoration etc.). And you’d better use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails (see next page).

UPLOAD

• First. set one light, which involves the program you have edited in EDIT menu and want to upload, in Master mode, and others in Slave mode.
• Then, connect all the lights with OMX cables. Finally, select the UPLOAD menu of the Master light and press ENTER. All the programs edited in the Master light will be uploaded to the Slave lights.

OMX Address-In this menu, you can select the DMX Address.

1. 1. Press “ENTER” button and then UP or DOWN button until “OMX Address ” is showed.
   2. Press “ENTER” button, and “OMX Address” will be showed. Then press ENTER.

1. “xxx” will be showed, “xxx” represents the showed address. You can press the UP or DOWN button to desired

Channels Mode-In this menu, you can connect several pieces of lights with DMX cable and control them with control console.

1. Press “ENTER” button and then UP or DOWN button until “Channels Mode” is showed
2. Press “ENTER” button, and “Channels Mode” will be showed. Then press ENTER.
3. “Channel [xx]” will be showed, “X” represents the showed DMX channel mode. You can press the UP or DOWN button to select your desired Channel mode.

DMX State-In this menu, you can learn about the information of DMX Hold and Blackout.

1. Press “ENTER” button and then UP or DOWN button until “DMX State” is showed.
2. Press “ENTER” button, and “DMX Hold” or “Blackout” will be showed. Then press ENTER and uni can calert wour decired made

Manual Mode-In this menu, you can adjust the value of static color and strobe speed as you like.

1. Press “ENTER” button and then UP or DOWN button until “Manual Mode” is showed.
2. Press “ENTER” button, and there are six options. Then press ENTER to select the option and press UP or DOWN button to select the value you desire as below:
3. RED – You can adjust the red brightness in this menu.
4. GREEN – You can adjust the green brightness in this menu.
5. BLUE – You can adjust the blue brightness in this menu.
6. WHITE – You can adjust the white brightness in this menu.
7. COLOR -You can select 255 static color in this menu.
8. STROB – You can adjust the strobe speed in this menu.

AUTO mode-In this menu, you can select your desire AUTO mode and adjust the running speed.

1.  Press “ENTER” button and then UP or DOWN button until “AUTO mode” is showed.
2. Press “ENTER” button, and “SPEED” or “AUTO MODE” will be showed. Then press ENTER, and you can see two items as below:
3. SPEED – You can select your desired speed in this menu.
4. ALJTO MODE – You can select your desired auto mode in this menu

Slave Mode-In this menu, you can select SLAVE mode. In SLAVE mode, you can select one light as the MASTER light and other lights in SLAVE mode will run following the MASTER light.

1. Press “ENTER” button and then UP or DOWN button until “Slave MODE” is showed.
2. Press “ENTER” button, and “SLAVE” will be showed, then press ENTER to confirm.

CUSTOMER Mode-In this menu, you can select the AUTO program edited in the “EDIT” menu.

1. Press “ENTER” button and then UP or DOWN button until “CUSTOMER” is showed.
2. Press “ENTER” button, and there are 11 pre-programmed mode edited in the “EDIT” menu. EDIT Mode-In this menu, you can edit your desired AUTO program.
3. Press “ENTER” button and then UP or DOWN button until “EDIT” is showed.
4.  Press “ENTER” button, and open the “EDIT” mode to edit the custom programs from”PR.01″ to “PR.11”.And there are 32 scenes that can be edited in each custom program.
5.  You can edit a scene by adjusting the value of “RED (0~255)”, “GREEN (0~255)”, “BLUE (0~255)”, “WHITE (0~255)”, “FADE (0~30)”, “FLASH (0~30)”, “STROBE (0~30)” & “TIME (0~30)” as you like. Then the data will be saved, when you press the ENTER button for 5 seconds.

UPLOAD-In this menu, you can connect several pieces of lights with MAX cables and set one light as the MASTER and others in SLAVE mode. Then upload the custom program in the MASTER light to the lights in SLAVE mode.

1.  Press “ENTER” button and then UP or DOWN button until “UPLOAD” is showed.
2. Press “ENTER” button to upload the custom programs from the MASTER light to the SLAVE ones. The password is [UP] + [DOWN] + [UP ] + [DOWN ].

SET UP-In this menu, you can adjust the value of the function.

1. Press “ENTER” button and then UP or DOWN button until “SET UP” is showed.
2. Press “ENTER” button, and there will be nine options. Then, press ENTER to select the option and press UP or DOWN button to select the value you desire as below.
3. ID number – You can select an ID Number in this menu. Then, you can adjust the value of channel 11 to the corresponding scope and control the light individually with control console.
4. CAL WHITE- You can select the value of 11 different white color. And there are 11 pre-programmed White colors that can be edited by adjusting the value of “Red”, “Green”, “Blue”, “White”.
5. LCD BLACK – In this item, you can select “ON” or “30S”. If you select “ON”, the displayer will be on all the time. And if you select “30S”, the displayer will extinguish about ten seconds later.
6. Key locks – You can select whether the password is ON or 30S in this menu, and the password is [UP] + [DOWN] + [UP] + [DOWN] .If you select “ON”, then you have to input the password before pressing the buttons. Otherwise, the light won’t respond to your order.
7. Max temp – You can set the your desired Max working temperature about the light in this menu. When the working temperature of the light exceeds the Max temperature, the color of letter “Temp xx°C” showed in the menu will change from white to yellow. Meanwhile, the light will adjust the working temperature automatically.
8. Dimmer ALL – You can adjust the brightness of each color in this menu.
9. Factory Reset – You can reset the light.

INFORMATION-In this menu, you can learn about the information of software, hardware and the working time of the light.

1. Press “ENTER” button and then UP or DOWN button until “INFORMATION” is showed.
2. Press “ENTER” button, and “Software” “Hardware” or “Fix times” will be showed. Then press ENTER, and you can see three items as below:
3. Software – This item displays the Software information.
4. Hardware – This item displays the Hardware information.
5. Fix times – This item displays the working hours about the light.

RESET-In this menu, you can reset all the value of the system.

1. Press “ENTER” button and then UP or DOWN button until “RESET” is showed.
2. Press the ENTER button to reset all the value of the system.

DMX-512 addressing with ID address

1. Follow instructions 1 for DMX 512 addressing.
2. Activate ID addressing in each fixture by setting panel function “ID ON/OFF” to ON. “Settings” to “ID ON/OFF” to “ON” For every DMX 512 starting address the user can set 66 separate ID addresses. Set ID addresses in each fixture by setting panel function ” ID address” to incremental values. (I.e. 1, 12, 24, 36 etc…) “Settings” to “address” to “01~66”.

The figure above shows a simple DMX layout which has used three units at each DMX address. The three units have different ID addresses which allows the user to collectively control the whole group units at that DMX address by setting Channel 10 to 0, or to control each unit independently by first selecting the DMX address and then by using Channel 11 to locate the target ID address. (Note that when using ID addresses it is also possible to activate ADAS which allows for even more option with DMX addressing and control.

Channel 12 (ld address set)

DMX control mode DMX 3 channel

DMX 6 channel

DMX 8 channel

DMX 12 channel

9

| 000-010| No function
011-012| Color 1
013- 016| Color 2
017 – 023| Color 3
024-027| Color4
028 – 031| Color 5
032-035| Color 6
036-039| Color 7
040-043| Color 8
044- 047| Color 9
048-051| Color 10
052-055| Color 11
056-059| Color 12
060-063| Color 13
064-067| Color 14
068-071| Color 15
072-083| Color 16
084-087| Color 17
088-091| Color 18
092-095| Color 19
096-099| Color 20
100-103| Color 21
104-107| Color 22
108-111| Color 23
112-115| Color 24
116 – 123| Color 25
124-127| Color 26
128-131| Color 27
132-135| Color 28
136-139| Color 29
140 – 143| Color 30
144 – 147| Color 31
148-151| Color 32
152 – 155| Color 33
156 – 159| Color 34
160 – 163| Color 35

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>