ENFORCER SD-9163-KSQ Outdoor Wave to Open Sensor with Manual Override User Guide
- June 13, 2024
- ENFORCER
Table of Contents
ENFORCER SD-9163-KSQ Outdoor Wave to Open Sensor with Manual Override
Product Information
The ENFORCER Outdoor Wave-to-Open Sensor is a full-featured exit plate that uses IR technology to allow egress from a protected area or activate a device with the simple wave of a hand. It is designed for outdoor use and is weather- resistant (IP65). The sensor is suitable for various environments such as hospitals, clinics, labs, cleanrooms, schools, factories, or offices. It features a stainless steel plate and comes in slimline or single-gang options. The sensor has an adjustable range of up to 7 inches (18cm) and a 1.2A relay with adjustable trigger duration of 0.5 to 30 seconds. It also has selectable LED colors to indicate sensor activation. Some models include a manual override button that functions without electricity in case of power failure.
Specifications
- Model : SD-9163-KSQ, SD-9263-KSQ, SD-9163-KSVQ, SD-9263-KSVQ
- Dimensions : Not specified
- Operating Voltage : 12-24 VDC
- Current Consumption : 13mA / 15mA (SD-9163-KSQ), 18mA / 23mA (SD-9263-KSQ), 23mA / 28mA (SD-9163-KSVQ), 28mA / 35mA (SD-9263-KSVQ)
- Contact Rating : Form C dry contact, 1.2A@24VDC
- Response Time : 10mS
- Trigger Duration : 0.5 to 30 seconds (toggle)
- Sensor Range : 2 to 7 feet (5 to 18cm)
- Available Faceplates : English, Spanish, French
Product Usage Instructions
- Choose the appropriate model of the Outdoor Wave-to-Open Sensor based on your requirements.
- Ensure proper installation of the sensor following the provided instructions.
- Connect the sensor to a power source with a voltage range of 12-24 VDC.
- Make the necessary wiring connections according to the provided diagram. The purple wire represents the normally open (N.O.) contact, and the green wire represents the normally closed (N.C.) contact. Note that the manual override button is prewired for certain models.
- Adjust the sensor range up to 7 feet (18cm) as needed.
- Configure the trigger duration from 0.5 to 30 seconds using the adjustable settings.
- Select the desired LED color mode to indicate sensor activation (applicable to specific models).
- In case of power failure, utilize the manual override button to operate the sensor without electricity (applicable to specific models).
Please refer to the user manual for detailed instructions and safety precautions.
Outdoor Wave-to-Open Sensors
- SD-9163-KSQ Slimline, English*
- SD-9163-KSVQ Slimline, English,* Manual Override, ETL UL294 Listed
- SD-9263-KSQ Single-Gang, English*, ETL UL294 Listed
- SD-9263-KSVQ Single-Gang, English,* Manual Override, ETL UL294 Listed
The ENFORCER Outdoor Wave-to-Open Sensor is a full- featured exit plate which uses IR technology to allow egress from a protected area or activate a device with the simple wave of a hand. Since no touch is required, this sensor is suitable for use in hospitals, clinics, labs, cleanrooms (to reduce the risk of contamination), schools, factories, or offices.
Features
- Weather-resistant (IP65) for outdoor use†
- Clean and simple no-touch operation reduces the risk of cross-contamination
- Adjustable sensor range up to 7″ (18cm)
- Stainless steel plate, available in slimline or single-gang
- 1.2A relay, adjustable trigger duration 0.5~30 seconds
- Selectable LED colors (turns from red to green or green to red) to show if the sensor is activated
SD-9163-KSVQ and SD-9263-KSVQ only
Manual override button functions without electricity in case of power failure
Specifications
Model| SD-9163-KSQ SD-9163-KSVQ| SD-9263-KSQ
SD-9263-KSVQ
---|---|---
Operating voltage| 12~24 VDC
Current draw (max. ±10%)| Standby (12/24 VDC)| 13mA / 15mA| 18mA / 23mA
Triggered (12/24 VDC)| 23mA / 28mA| 28mA / 35mA
Relay type| Form C dry contact, 1.2A@24VDC
Response time| 10mS
Output time| 0.5~30s, toggle
Range| 2″~7′ (5~18cm)
IP Rating| IP65†
Operating temperature| -4°~131° F (-20°~55° C)
Dimensions| 11/2″x41/2″x11/2″
(39x115x39 mm)
| 23/4″x41/2″x11/2″
(70x115x39 mm)
Sample Installation
Ordering
Information 
*Also available with European faceplate in English, Spanish, and French models
†Spanish and French faceplates available by special order
SECO-LARM® U.S.A., Inc. 16842 Millikan Avenue, Irvine, CA 92606
- Phone : 949-261-2999 | 800-662-0800
- Fax : 949-261-7326
- Website : www.seco-larm.com
- Email : sales@seco-larm.com
- Copyright © 2023 SECO-LARM U.S.A, Inc. All rights reserved.
All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective
owners.
The SECO-LARM policy is one of continual development. For that reason, SECO-
LARM reserves the right to change prices and specifications without notice.
SECO-LARM is not responsible for misprints.
PI_SD-9×63-KSxQ_230105.docx
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>