AVTech BATBOOK610LIP 6x10W RGBW Battery LED Washer User Manual

AVTech BATBOOK610LIP 6x10W RGBW Battery LED Washer

Product Information

Specifications:

• ELECTRICAL: Power consumption: 24W, Voltage: AC 110 – 240V, 50/60Hz
• BATTERY: Lithium Batteries, 11.1V, 9AH, Charge Time: 3.5 Hours, Working Time: 5H Full Power @ 24W; 8H full power @ 20W; 12H full power @ 15W. Maximum 30H with auto mode
• DYNAMIC EFFECT: Electronic dimmer allowing light adjustment from 0 to 100%, Built-in Effects: colour mixing, variable colour chasing, strobing, and fading
• CONTROL: IR Remote Control, Wireless DMX Solution, Run Mode: Wireless and wired by DMX 512/Master-Slave/Auto Mode
• SOFTWARE: 10 internal programs, 4 different dimming curves, Set refresh rate: 600HZ, 1200HZ, 2400HZ, 4800HZ, 9600HZ, 15000HZ, 11 kinds of colour temperature white, Working time record
• PHYSICAL: Material: Aluminum body with black sand coat, Install solution: M10 holes for Clamp, Safety ring holes, Magnetic frost filter (Optional choose), Dimensions: 225150130.5mm, N.W: 3.3 KG, IP65

Product Usage Instructions

Safety and Handling:
Before operating the BATBOOK610 LIP LED Washer, read the user manual carefully. This product is for professional use only and should not be used for household purposes. Always exercise caution when operating the unit.

Troubleshooting:

• The fixture does not turn on: Check if the battery is empty. Connect it to the power cable and try again.
• The LEDs do not emit light: Ensure the fixture is not in BLACKOUT mode or DMX Hold. Consider performing a Factory Reset.
• Incorrect colour or effect display: Perform a Factory Reset to clear any previous settings.
• Battery runtime issues: Adjust the RUNTIME setting for longer battery life. Consider using colours that consume less power or warming up the battery if runtime is still short.
• Fixture cannot be controlled: If resetting does not help, consult authorized personnel.

Programme Menu:
Refer to the user manual for detailed instructions on accessing and utilizing the various modes and settings available in the BATBOOK610 LIP LED Washer.

FAQ:

• Q: Can the battery be replaced?
  A: The BATBOOK610 LIP LED Washer comes with Lithium Batteries that are replaceable. Contact our customer service for assistance with battery replacement.

• Q: How do I adjust the colour temperature?
  A: Use the menu options to select from the available colour temperature settings ranging from 3000K to 10000K.

Packaging:
Thanks for your purchasing the BATBOOK610LIP. All the lights have been checked and are in excellent operating condition. Please check the shipping carton first, because there may be damage occurred during the shipment. Then check the lights carefully and be sure that the lights are intact and work normally. In the event damage has been found, spare parts are missing or the lights work abnormally, please contact us for further instructions. And please don’t return the lights to the dealer before contacting us.

Introduction:
The BATBOOK610LIP is a mini wall washer with excellent performance. It is 200mm long, but the width of the covering wall is 5m. 2.4G remote control is included. The house is made of extruded aluminium and a die-cast aluminium cover. The ingress protection rating is IP65. However, there is no glue was used in the light. BATBOOK610LIP has won many certifications, including the CE, ROHS and so on.

SAFETY AND HANDLING

Before you operate this unit read the manual carefully. Always make sure to include the manual if you pass/rent/sell the unit to another user. Keep in mind that this manual cannot address all possible dangers and environments. Please use your caution when operating. This product is for professional use only. It is not for household use.

• Do not operate the unit in areas of high-temperature conditions. It will cause an abnormal function or damage the product.
• Always use a suitable safety wire when mounting the light overhead.
• Connect the safety wire only to the intended safety mount.
• Always follow local safety requirements.
• Only qualified personnel may repair this product.
• Do not open the product housing.
• Do not apply power if the light is damaged.
• Do not directly look into the light.
• It can cause harm to your eyes.
• Do not look at the LEDs with a magnifying glass or any other optical instrument that may concentrate the light output.
• The exterior surfaces of the light can become hot, up to 70°C during normal operation.
• Ensure that accidental physical contact with the device is impossible.
• Install only in ventilated locations.
• Do not cover the light.

LI-ION Battery:
A rechargeable lithium-ion battery is built into this unit.

• Only authorized personnel may service the battery.
• Do not place in fire or heat.
• Do not use or charge the light if it is damaged.
• Avoid bumping or plunging, it may cause fire or explosion.
• Never store the battery when fully drained.
• Always recharge immediately when empty.
• Make sure to fully charge all units before storing them.
• Partially charged batteries will lose capacity.
• The battery may only be replaced with an original spare part.
• Always charge with the flight case open.
• It is recommended to charge at a temperature between 15°C and 35°C
• The light contains a lithium-ion battery.
• Don’t throw the unit into the garbage at the end of its lifetime.
• Make sure to dispose of it according to your local ordinances and/or regulations, to avoid polluting the environment!
• The packaging is recyclable and can be disposed of.

Troubleshooting

• The fixture does not turn on.
  The battery may be empty. Connect it to the power cable and try again.

• The fixture turns on and the display is on, but the LEDs do not emit light.
  The fixture could be set to BLACKOUT mode, set to DMX Hold and doesn’t receive a valid signal. It is good practice to do a Factory Reset.

• The fixture is not working correctly – it does not display the colour or effect chosen.
  The fixture may still be operating under a previous setting. It is good practice to do a Factory Reset.

• After completing RESET SETTINGS, the fixture still cannot be controlled.
  Please turn off the light and turn it on again, if cannot be controlled, too, please consult an authorized person.

• The fixture does not run long enough on battery.

  • The required RUNTIME can be set. It defaults to several hours. To achieve a greater battery runtime, set the RUNTIME to the required value. Alternatively, program the fixture to only display colours that use less power, such as Red,
  • Green, Blue and White.
  • If the runtime is still too short, consider that it is reduced slightly if the battery is very cold.

• The power cable is connected but the fixture is not charging.
  The battery may be fully charged. Please read our user manual for more details. The fixture will only commence charging when its battery has a temperature of 45° or less. Turn the fixture off and let it cool down; once cold enough, it will start charging. If it still not charging, please consult an an authorized person.

Features

OPTICS

• Light Source: 6*10W, 4 in 1 RGBW LEDs
• Lens: Standard 12 °, optional choose:20,30,45°

ELECTRICAL

• Power consumption: 24W
• Voltage: AC 110 – 240V, 50/60Hz

BATTERY

• Battery: Lithium Batteries,11.1V,9AH
• Charge Time: 3.5 Hours
• Working Time: 5H Full Power@24W; 8H full power @20W,12H full power@15W. Maximum 30H with auto mode.

DYNAMIC EFFECT

• Electronic dimmer, allowing perfect light adjustment from 0 to 100% without colour variation;
• Built-in Effect: colour mixing, variable colour chasing, strobing and fading.

CONTROL

• IR Remote Control
• Wireless DMX Solution from Sweden
• Run Mode: With wireless and wired by DMX 512 /Master-Slave /Auto Mode

SOFTWARE

• 10 internal programs
• 4 different dimming curve
• Set refresh rate:600HZ,1200HZ,2400HZ,4800HZ,9600HZ,15000HZ.
• 11 kinds of color temperature white
• Working time record

PHYSICAL

• Material: Aluminum body, black sand coat.
• Install solution: M10 holes for Clamp
• Safety ring holes
• Magnetic frost filter(Optional choose)
• Dimensions: 225150130.5mm
• N.W: 3.3 KG
• IP65

Programme Menu

Displayer Introduction

1. When you enter DMX Mode, it will be shown DMX, when you enter SLAVE Mode, it will be shown SLAVE.
2. This shows the condition of signal transmission. Green is connected. Red is disconnected.
3. This shows the temperature of the lights.
4. This shows the menus you can select.
5. This shows the condition of the wireless signal. Green is connected. Red is disconnected.
6. This shows the battery’s electric quantity.

• While DMX and Wireless signals are green, it means DMX Mode and Wireless are connected.
• While DMX shows red the Wireless signal shows green, which means DMX Mode is disconnected and Wireless is connected.
• While DMX shows green but the Wireless signal shows red, it means DMX Mode is connected and Wireless is disconnected.
• While DMX and Wireless are shown in red, it means DMX Mode and Wireless are disconnected.
• While the letters and numbers show a change from white to yellow, it means the temperature is beyond max temperature of default settings.
• While the letters unnumbered show an Error, it means to have some problems with temperature.
• While the battery is charging, it will show running from empty to full. When you stop charging, it will show how much the electric quantity.

DMX-In this menu, you can connect several pieces of lights with DMX cable and control them with a control console.

1. Press the “ENTER” button and then the UP or DOWN button until “DMX ” is shown.
2. Press the “ENTER” button, and “CHANNEL” or “ADDRESS” will be shown. Then press ENTER.
3. “Channel [xx]” will be shown, and “X” represents the DMX channel mode. You can press the UP or DOWN button to select your desired Channel mode.
4. “xxx” will be shown, “x” represents the shown address. You can press the UP or DOWN button to select your desired address.

RUN MODE-In this menu, you can select DMX mode or SLAVE mode. In SLAVE mode, you can select one light as the MASTER light and other lights in SLAVE mode will run following the MASTER light.

1. Press the “ENTER” button and then the UP or DOWN button until “RUN MODE” is shown.
2. Press the “ENTER” button, and“DMX” or “SLAVE” will be shown, then press ENTER to select your desired mode.

SET In this menu, you can adjust the value of the function.

1. Press the “ENTER” button and then the UP or DOWN button until “SET UP” is shown.
2. Press the “ENTER” button, and there will be nine options. Then, press ENTER to select the option and press UP or DOWN button to select the value you desire as below.
3. ID number – You can select an ID Number in this menu. Then, you can adjust the value of channel 11 to the corresponding scope and control the light individually with the control console.
4. Display Led – In this item, you can select “ON” or “OFF”.If you select ON, the display will be on all the time. If you select OFF, the displayer will extinguish about ten seconds later.
5. Key locks – You can select whether the password is on or off in this menu, and the password is [ DOWN ] + [ UP ] + [ DOWN ] + [ UP ]. If you select “on”, then you have to input the password before pressing the buttons. Otherwise, the light won’t respond to your order.
6. Max temp – You can set your desired Max working temperature for the light in this menu. When the working temperature of the light exceeds the maximum temperature, the colour of the letter “Temp xx” shown in the menu will change from white to yellow. Meanwhile, the light will adjust the working temperature automatically.
7. Dimmer RED – You can adjust the red brightness in this menu.
8. Dimmer GREEN – You can adjust the green brightness in this menu.
9. Dimmer BLUE – You can adjust the blue brightness in this menu.
10. Dimmer WHITE – You can adjust the white brightness in this menu.
11. Dimmer ALL – You can adjust the brightness of each colour in this menu.

INFORMATION In this menu, you can learn about the information of software, hardware and the working time of the light.

1. Press the “ENTER” button and then the UP or DOWN button until “INFORMATION” is shown.
2. Press the “ENTER” button, and“Software” “Hardware” or “Fix times” will be shown. Then press ENTER, and you can see three items as below:
3. Software – This item displays the Software information.
4. Hardware – This item displays the Hardware information.
5. Fix times – This item displays the working hours of the light.

AUTO-In this menu, you can select your desired AUTO mode and adjust the running speed.

1. Press the “ENTER” button and then the UP or DOWN button until “AUTO” is shown.
2. Press the “ENTER” button, and“SPEED” or “PROGMA MODE” will be shown. Then press ENTER, and you can see two items as below:
3. SPEED – You can select your desired speed in this menu.
4. PROGMA MODE – You can select your desired auto mode in this menu.

CUSTOM MODE-In this menu, you can select the AUTO program edited in the “EDIT” menu.

1. Press the “ENTER” button and then the UP or DOWN button until “CUSTOM MODE” is shown.
2. Press the “ENTER” button, and there are 11 pre-programmed modmodesitted in the “EDIT” menu.

CAL WHITE-In this menu, you can adjust the value of 11 different white colours.

1. Press the “ENTER” button and then the UP or DOWN button until “CAL WHITE” is shown.
2. Press the “ENTER” button, and there are 11 pre-programmed White colcoloursat that can be edited by adjusting the value of “Red”, “Green”, “Blue” and  “White”.

STAT COLOR-In this menu, you can adjust the value of static colour and strobe speed as you like.

1. Press the “ENTER” button and then the UP or DOWN button until “STAT COLOR” is shown.
2. Press the “ENTER” button, and there are six options. Then press ENTER to select the option and press the UP or DOWN button to select the value you desire as below:
3. STAT RED – You can adjust the red brightness in this menu.
4. STAT GREEN – You can adjust the green brightness in this menu.
5. STAT BLUE – You can adjust the blue brightness in this menu.
6. STAT WHITE – You can adjust the white brightness in this menu.
7. STAT AMB – You can adjust the amber brightness in this menu.
8. STAT UV – You can adjust the purple brightness in this menu.
9. SELECT COLOR -You can select 52 static colours in this menu.
10. STAT STROB – You can adjust the strobe speed in this menu.

EDIT-In this menu, you can edit your desired AUTO program.

1. Press the “ENTER” button and then the UP or DOWN button until “EDIT” is shown.
2. Press the “ENTER” button, and open the “EDIT” mode to edit the custom programs from“PR.01” to “PR.11”.21 scenes can be edited in each custom program.
3. You can edit a scene by adjusting the value of “RED (0~255)”, “GREEN (0~255)”, “BLUE (0~255)”, “WHITE (0~255)”, “AMBER (0~255)”, “PURPLE (0~255)”, “FADE (0~31)”, “FLASH(0~50)”, “STROBE (0~31)” & “TIME (0~100)” as you like. Then the data will be saved when you press the ENTER button for 5 seconds.

UPLOAD-In this menu, you can connect several pieces of lights with MAX cables and set one light as the MASTER and others in SLAVE mode. Then upload the custom program in the MASTER light to the lights in SLAVE mode.

1. Press the “ENTER” button and then the UP or DOWN button until “UPLOAD” is shown.
2. Press the “ENTER” button to upload the custom programs from the MASTER light to the SLAVE ones.

RESET-In this menu, you can reset all the values of the system.

1. Press the “ENTER” button and then the UP or DOWN button until “RESET” is shown.
2. Press the ENTER button to reset all the values in the system.

DMX control mode

2 CHANNELS

Channel| Value| Function
1| 0-255| Colour 1-colour 51
2| 0-255| White color marco: 3000K-10000K
HSV CHANNELS

Channel| Value| Function
1| 0-255| Hue
2| 0-255| Saturation
3| 0-255| Value (brightness)
5 CHANNELS

Channel| Value| Function
1| 000 – 255| Red
2| 000 – 255| Green
3| 000 – 255| Blue
4| 000 – 255| White
5| 000 – 255| Strobe (slow-fast)
8 CHANNELS

Channel| Value| Function
1| 000 – 255| Master dimmer
2| 000 – 255| Red
3| 000 – 255| Green
4| 000 – 255| Blue
5| 000 – 255| White
6| 000 – 255| Colour 1-colour 51
7| 000 – 255| White color marco: 3000K-10000K
8| 000 – 255| Strobe (slow-fast)
11 CHANNELS

Channel| Value| Function
1| 000 – 255| Master dimmer
2| 000 – 255| Red
3| 000 – 255| Green
4| 000 – 255| Blue
5| 000 – 255| White
6| 000 – 255| Colour 1-colour 51
7| 000- 255| White color marco: 3000K-10000K
8| 000 – 255| Strobe (slow-fast)
9| 000 – 255| Auto 1-12
10| 000 – 255| Auto speed

11

| 000 – 009| No function
010 – 029| Linear dimmer
030- 069| Dimmer 1 (fast)
070 – 129| Dimmer 2
130 – 189| Dimmer 3
190 – 255| Dimmer 4(slow)
15 CHANNELS

Channel| Value| Function
1| 000 – 255| Master dimmer
2| 000 – 255| Red
3| 000 – 255| Red fine
4| 000 – 255| Green
5| 000 – 255| Green fine
6| 000 – 255| Blue
7| 000 – 255| Blue fine
8| 000 – 255| White
9| 1 – 255| White fine
10| 000 – 255| Colour 1-colour 51
11| 000- 255| White color marco: 3000K-10000K
12| 000 – 255| Strobe (slow-fast)
13| 000 – 255| Auto 1-12
14| 000 – 255| Auto speed

15

| 000 – 009| No function
010 – 029| Linear dimmer
030- 069| Dimmer 1 (fast)
070 – 129| Dimmer 2
130 – 189| Dimmer 3
190 – 255| Dimmer 4(slow)

Mounting

• When installing the unit, the trussing or area of installation must be able to hold 10 times the weight without any deformation. When installing the unit must be secured with a secondary safety attachment, e.g. an appropriate safety cable. Never stand directly below the unit when mounting, removing, or servicing the unit.
• Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and periodic safety inspection of all installation materials and units. If you lack these qualifications, do not attempt the installation yourself.
• The installation should be checked by a skilled person once a year.
• The BATBOOK610LIP is fully operational in two different mounting positions, hanging upside-down from a ceiling or set on a flat-level surface. To avoid internal damage to the unit, never mount the unit on its side as illustrated above.
• Be sure this fixture is kept at least 0.5m away from any flammable materials (decoration etc.). You’d better use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails.

Product Overview

CHARGE WITH ABS CASE

• DURING THE COMPLETE PROCESS OF BATTERY CHARGE THE UPPER COVER OF THE FLIGHT MUST BE ALWAYS OPEN.
• DURING THE COMPLETE PROCESS OF BATTERY CHARGE THE PROJECTORS MUST BE ALWAYS OFF.

For correct use of the battery it is strongly recommended to:

• Charge the battery at least one time each month
• The minimum level of the charge must be not less than 5%

During the charge, the battery icon (visible on the display) will show the level of the charge. When the charge is finished, the icon will be green.

Connection in wireless mode – Master/Slave
When connecting to wireless mode, please remember to release first.

Both blinking red colour

| ****

the wireless transmitter or receiver OFF or not linked with the projector

Both are blinking but the wireless green| ****

Master and Slave with the projector does not connect success

Both fixed green colour

| Master-Transmitter mode ON and linked with the projector Slave-Receiver

Connection in wireless mode -DMX

When connecting to wireless mode, please remember to release first.

DMX-led status and wireless indicator

|

Description

---|---
Both blinking red colour| DMX not connected wireless transmitter OFF or not linked with the projector
Both blinking but:

DMX red – Wireless green

| ****

DMX is not connected, the transmitter is ON and linked with the projector

Both fixed green colour| Dmx connected, transmitter ON and linked with the projector

Tips & tricks

There are limitations to how wireless waves propagate through air. Physical barriers like glass, concrete and walls will limit the transmission range. Always try to have a clear line of sight between transmitters and receivers.

2.4G Remote

How to connect 2.4G remote control

1. Press and hold the button for 3 seconds to turn on or off the power of the remote control (the indicator light indicates that the remote control is turned on, and the remote control power will be automatically turned off after 1 minute of no operation).
   The indicator light will automatically turn off after 1 minute of use and needs to be pressed again for 3 seconds to turn on again.

2. Press and hold the button for 5 seconds, the indicator blinks, enters the matching mode, and automatically exits the pair mode after 20 seconds.

3. Turn on the light and enter [SETUP]→[REMOTE]→[ON], press the [ENTER] key to enter the matching mode. (If [ON] is displayed in the [REMOTE] mode during startup, you need to press the [ENTER] key again to enter the matching mode.)

4. During the flashing of the remote control light, the lamp flashes 3 times, which means that the connection is successful.

5. After the match is successful, when the remote control light is on, it means that the group of lamps is being controlled.

6. If multiple lamps need to be connected, please repeat the above steps and press the button to select different groups for connection. (Each group can connect up to 50 lamps.)

7. The furthest remote control distance of this product is about 50 meters. No need to rematch after a power failure.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>