AVTech SATURN700RGB 700W Power LED Tilt Moving Strobe User Manual
- June 4, 2024
- AVTECH
Table of Contents
AVTech SATURN700RGB 700W Power LED Tilt Moving Strobe
Specifications
- Product Name: SATURN70 0 RGB
- Power: 700W LED tilt moving strobe
- Usage: Indoor and outdoor (IP65)
Product Usage Instructions
Safety Instructions
- After receiving the lights, check for any damages caused by transportation. If there are damages, do not use the device and contact your dealer or manufacturer immediately.
- Do not install the fixture on inflammable surfaces directly.
- The fixture should only be handled by qualified personnel for installation, operation, and maintenance.
- Maintain a minimum distance of 3 meters when projecting the beam onto inflammable surfaces.
Dimensions
- Refer to the product manual for detailed dimensions.
Control Panel
- The control panel includes operation buttons for mode selection, power input/output details, ART-NET and DMX connections. Follow the specific panel operations as described in the manual.
Lighting Parameters
- Refer to the Technical Data Sheet for detailed optical and electronic parameters of the product.
FAQ
Q: Can this product be used outdoors?
A: Yes, the product is suitable for both indoor and outdoor use with an IP65 rating.
Q: What is the power requirement for this product?
A: The input voltage range is 100-240V at 50/60Hz with a power output of 700W.
Before using this lamp, please read this manual thoroughly
Safety instructions
- After receiving the lights, please open to check whether there is any damage caused by transportation.
- In case of damages caused by transportation, please don’t this device and contact your dealer or manufacturer as soon as possible.
- The projector is for indoor and outdoor use, IP65.
- Do not install the fixtures onto inflammable surfaces directly.
- The fixture is only intended for installation, operation and maintenance by qualified personnel.
- Do not project the beam onto inflammable surfaces, minimum distance is 3 meters. 3m
- Avoid direct exposure to the light from the lamp. The light is harmful to the eyes.
- Do not attempt to dismantle and/or modify the projector in any way.
- Electrical connection must only be carried out by qualified personnel.
- Before installation, ensure that the voltage and frequency of the power supply match the power requirements of the fixture.
- It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.
- Do not connect this device to any other type of dimmer apparatus.
- The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be attached as shown in the “Installing the projector” section.
- Shields and lenses shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired, for example by cracks or deep scratches.
- The exterior surface temperature of the luminaire after 5 minutes of operation is 45℃ when steady state is achieved 70℃. There are no user-serviceable parts inside the projector, do not open the housing and never operate the fixture with the covers removed.
- There are no user-serviceable parts inside this light, please check whether all covers or shells have been installated and screws have beed tightened securely. It is forbidden to use lights with covers(or shells) open.
- If you have any questions, don’t hesitate to consult your dealer or manufacturer.
Dimensions
control Panel
- Panel operation buttons: mode UP Down Enter
- power input: IP65 POWER CON cable Input voltage 100-240V 50/60HZ
- Power Output: IP65 POWER CON power cable Output voltage 100-240V 50/60HZ
- ART-NET input: Connect network input
- DMX input: 3-core DMX waterproof signal line input
- DMX output: 3-core DMX waterproof signal line output
- ART-NET output: Connect network output
- The specific operations of the panel functions are as follows:
Display panel function description
- Press the button UP or DOWN if you want to browse through the various Setup Options.
- Press the button ENTER to save your settings or enter the next menu.
- Press the button UP or DOWN to shift.
- Press button Menu will return to the upper menu one by one.
Lighting parameter
Technical Data Sheet
Optical parameters|
---|---
light source| 1.56W white 392pcs 2835 lamp beams,1W RGB3 in1 784pc 5050 lamp
beads
color temperature| 2800K-8000K
Optical output of the whole machine| R:5480 Lm；G：11760 lm；B：1560 lm；W：45000
lm；ALL：63880 lm
Illumination| ALL:/ Lux: R：/ Lux: G：/ Lux: B：/ Lux: W：/ Lux: @5m
Colour rendering index| Ra≥90
R9| ≥90
dominant
wavelength
| R：622nm；G：525nm；B：457nm
Light source life| 20000H
beam angle| 110°
|
dynamic effect|
strobe| 0～20Hz
Dimming| Four dimming curves, 0-100% dimming
|
Electronic
parameters
|
Input voltage and
frequency
| 100～240VAC,50～60Hz
power| Full brightness 700W，Strobe 1200W
power connection| Waterproof POWERCORN input;
signal connection| Waterproof 3-core DMX signal line input/output, the maximum
number of connections is 32; waterproof network signal input and output
Power Factor| 0.95 @230V
working environment| -10°～45°
switching power supply| 100～240VAC, 50～60Hz,28V 800W
|
Structural parameters|
Size| Product size：494×316×160 mm
Weight| Net weight：12.0Kg(Clamps and quick lock not included）
degree of protection| IP65
cooling system| Waterproof low-noise fan forced cooling
shell| Die-cast magnesium + aluminium alloy; black
installation method| side hanging, hanging installation
|
control|
---|---
control method| Art-net/DMX512/RDM
DMX Channel| 8/11/13/24/30/74/97CH
Display| TFT
refresh rate| 600Hz/1200 Hz/2000 Hz/4000 Hz/6000 Hz/25KHz
pixel matrix| white light 214，rgb 27
Accessories|
---|---
Standard| Standard power cord 1PC; manual 1PC
Optional|
menu function
| Main Level | Programming Levels | |
|---|---|---|
| 1 | Protocol | DMX512 |
Art-Net
sACN
2| DMX Address| 1–512*
3| DMX Channel| 8CH
11CH
13CH
24CH
30CH
74CH
97CH
4| Static| Fixed Color| R
G
B
GB
RB
RG
RGB
Manual Color Mixer| Red| 0-255
Green
Blue
5| Plate FX| Plate FX 1
Plate FX 2
Plate FX 3
Plate FX 4
Plate FX 5
Plate FX 6
Plate FX 7
| Speed| 1-100
Plate
Intensity
| 000-255
Background Color| R
G
B
GB
| | Plate FX 8
Plate FX 9
| | RB
---|---|---|---|---
RG
RGB
Off
Foreground Color| R
G
B
GB
RB
RG
RGB
Off
6| Beam Intensity| 000-255
7| Beam Flash Duration| 000-255
8| Beam Flash Rate| 000-255
9| Tilt| 000-255
10| Tilt Offset| 000-255
11| Tilt Invert| No
Yes
12| Pixel Invert| Plate1 Invert| No
Yes
Plate2 Invert| No
Yes
Tube1 Invert| No
Yes
Tube2 Invert| No
Yes
13| LED Array Swap| Plate Swap| No
Yes
Beam Swap| No
Yes
14| Master/Slave| Master
Slave
15| Dimmer Mode| OFF
DIM1–3
16| White Balance| Off
Manual| Red Green Blue| 125-255
17| LED
Frequency
| 600Hz
1200Hz
2000Hz
4000Hz
6000Hz
25000Hz
---|---|---
18| Fan Mode| ****
Auto
On
19| Display Invert| No
Yes
20| Backlight| 10s
30s
2Min
Always On
21| Key Lock| On
Off
22| Ethernet Setting| Universe| 0–255 (ArtNet)
1–255 (sACN)
IP Address| 2.192.0.1
23| Information| Fixture Hours:| Hours
LED Hours:| H
Disp Ver:| V.
Drv-Y Ver:| V.
LED-A Ver:| V.
LED-C Ver:| V.
Net Ver:| V.
UID|
24| Update Firmware| Only this Unit| .CHL
…
Multiple Units
| .CHL
…
Other Fixture Type
| .CHL
…
25| Factory Reset| No
Yes
Installation and connection
Installation diagram
Precautions
- This product is suitable for indoor and outdoor use, and its protection level is IP65. The lamp should be kept clean and should not be used in a humid or dusty environment. It should be maintained every three months.
- Only qualified professionals can install, operate and maintain the lamps, and ensure that the operation is strictly under the procedures described in this manual.
- The lamps and lanterns should be installed in a well-ventilated place, at least 50 away from the wall, and check whether the ventilation holes are unobstructed. Do not look directly at the light source to avoid damage to the eyes.
- Parts that make electrical connections must be operated by qualified installers.
- Each lamp should be safely grounded, and electrical installation should be carried out under relevant standards.
- Do not use the power cord with damaged insulation, and do not put the power cord on other wires.
- When the lamp is not in use or cleaned, please unplug the power cord. Do not pull or pull the power cord vigorously.
- If the back cover of the lamp is equipped with a safety buckle or a connection hole, for safety reasons, please use the safety rope to pass through the connection hole for auxiliary hoisting.08
power connection
This product uses a Power con in/out
input power cord
Note: Due to the power, a 1.5 square power cord
Do not connect too many lamps to a single power cord, or overload it.
Do not use the power cord with damaged insulation, and do not put the power
cord on other wires.
When the lamp is not in use or cleaning, please unplug the power cord。
Do not pull or plugin vigorously or drag the power cord directly.
signal connection
Internet connection
DMX Connection
DMX connection instructions
- To reduce signal errors and avoid signal weakening and interference during transmission, a 120 ohm 1/4W resistor can be added between the 2-core and 3-core of the DMX output of the last machine.
- Use the XLR signal cable to connect the lamps, one end to the output port of the lamp, and the other end to the input port of the next lamp. Signal lines can only be used in series, not in parallel.
- Because the DMX512 signal transmission speed is very fast when the signal line is damaged, the welding place is not strong, the contact is not good, etc., it will affect the signal transmission and cause the system to shut down.
- When the machine power of a certain unit is cut off, the connection of DMX output and input is bypassed to maintain the continuity of the DMX line.
- Each light must have an address code to be able to receive information from the console.
- The terminal of the DMX512 system needs to be equipped with a terminator to reduce errors in signal transmission.
DMX Address code setting
Ch| add| first address| Second, add| Third add|
Fourth add
---|---|---|---|---|---
8CH| 001-008| 001| 009| 017| 025
11CH| 001-011| 001| 012| 023| 034
13CH| 001-013| 001| 014| 027| 040
24CH| 001-024| 001| 025| 049| 063
30CH| 001-030| 001| 031| 061| 091
74CH| 001-074| 001| 075| 149| 223
97CH| 001-097| 001| 098| 195| 292
Refer to the above picture The number of lamps to be added after the fourth one; the address code is based on the channel, and so on.
channel table
97CH| | |
---|---|---|---
Channel| Function| Value| Percent/Setting
1| Tilt| 000-255| 0-100％
2| Fine tilt| 000-255| 0-100％
3| Master dimmer| 000-255| 0-100％
4| Plate dimmer| 000-255| 0-100％
5| Beam dimmer| 000-255| 0-100％
6| Plate flash duration| 000-009| Classic shutter mode: disables
duration control
010-250| Slow to fast
251-255| 100％On, no flash/strobe
7| Plate flash rate| 000-009| 100%
010-250| Slow to fast
251-255| 100%
8| Beam flash duration| 000-009| Classic shutter mode: disables
duration control
010-250| Slow to fast
251-255| 100％On, no flash/strobe
9| Beam flash rate| 000-009| 100%
010-250| Slow to fast
251-255| 100%
10| Plate pixel 1 red| 000-255| 0-100％
11| Plate pixel 1 green| 000-255| 0-100％
12| Plate pixel 1 blue| 000-255| 0-100％
13| Plate pixel 2 red| 000-255| 0-100％
14| Plate pixel 2 green| 000-255| 0-100％
15| Plate pixel 2 blue| 000-255| 0-100％
16| Plate pixel 3 red| 000-255| 0-100％
17| Plate pixel 3 green| 000-255| 0-100％
18| Plate pixel 3 blue| 000-255| 0-100％
19| Plate pixel 4 red| 000-255| 0-100％
20| Plate pixel 4 green| 000-255| 0-100％
21| Plate pixel 4 blue| 000-255| 0-100％
22| Plate pixel 5 red| 000-255| 0-100％
23| Plate pixel 5 green| 000-255| 0-100％
24| Plate pixel 5 blue| 000-255| 0-100％
25| Plate pixel 6 red| 000-255| 0-100％
26| Plate pixel 6 green| 000-255| 0-100％
27| Plate pixel 6 blue| 000-255| 0-100％
28| Plate pixel 7 red| 000-255| 0-100％
29| Plate pixel 7 green| 000-255| 0-100％
---|---|---|---
30| Plate pixel 7 blue| 000-255| 0-100％
31| Plate pixel 8 red| 000-255| 0-100％
32| Plate pixel 8 green| 000-255| 0-100％
33| Plate pixel 8 blue| 000-255| 0-100％
34| Plate pixel 9 red| 000-255| 0-100％
35| Plate pixel 9 green| 000-255| 0-100％
36| Plate pixel 9 blue| 000-255| 0-100％
37| Plate pixel 10 red| 000-255| 0-100％
38| Plate pixel 10 green| 000-255| 0-100％
39| Plate pixel 10 blue| 000-255| 0-100％
40| Plate pixel 11 red| 000-255| 0-100％
41| Plate pixel 11 green| 000-255| 0-100％
42| Plate pixel 11 blue| 000-255| 0-100％
43| Plate pixel 12 red| 000-255| 0-100％
44| Plate pixel 12 green| 000-255| 0-100％
45| Plate pixel 12 blue| 000-255| 0-100％
46| Plate pixel 13red| 000-255| 0-100％
47| Plate pixel 13 green| 000-255| 0-100％
48| Plate pixel 13 blue| 000-255| 0-100％
49| Plate pixel 14 red| 000-255| 0-100％
50| Plate pixel 14 green| 000-255| 0-100％
51| Plate pixel 14 blue| 000-255| 0-100％
52| Beam pixel 1| 000-255| 0-100％
53| Beam pixel 2| 000-255| 0-100％
54| Beam pixel 3| 000-255| 0-100％
55| Beam pixel 4| 000-255| 0-100％
56| Beam pixel 5| 000-255| 0-100％
57| Beam pixel 6| 000-255| 0-100％
58| Beam pixel 7| 000-255| 0-100％
59| Beam pixel 8| 000-255| 0-100％
60| Beam pixel 9| 000-255| 0-100％
61| Beam pixel 10| 000-255| 0-100％
62| Beam pixel 11| 000-255| 0-100％
63| Beam pixel 12| 000-255| 0-100％
64| Beam pixel 13| 000-255| 0-100％
65| Beam pixel 14| 000-255| 0-100％
66| Beam pixel 15| 000-255| 0-100％
67| Beam pixel 16| 000-255| 0-100％
68| Beam pixel 17| 000-255| 0-100％
69| Beam pixel 18| 000-255| 0-100％
70| Beam pixel 19| 000-255| 0-100％
71| Beam pixel 20| 000-255| 0-100％
72| Beam pixel 21| 000-255| 0-100％
---|---|---|---
73| Beam pixel 22| 000-255| 0-100％
74| Beam pixel 23| 000-255| 0-100％
75| Beam pixel 24| 000-255| 0-100％
76| Beam pixel 25| 000-255| 0-100％
77| Beam pixel 26| 000-255| 0-100％
78| Beam pixel 27| 000-255| 0-100％
79| Beam pixel 28| 000-255| 0-100％
80| Beam FX| 000-005| No function
006-042| Ramp up
043-085| Ramp down
086-128| Ramp up-down
129-171| Random
172-214| Lightning
215-255| Spikes
81| Plates foreground| 000-000| No function
001-002| White(2700K)
003-004| White(3200K)
005-006| White(4200K)
007-008| White(5600K)
009-010| White(8000K)
011| Blue R:0
G:0 B:255
W:0
012-048| Green+/Blue R:0
G:+ B:255
W:0
049| Cyan R:0
G:255 B:255 W:0
050-086| Green/Blue- R:0
G:255 B:-
W:0
087| Green R:0
G:255 B:0
W:0
088-124| Red+/Green R:+
G:255 B:0
W:0
125| Yellow R:255
G:255 B:0
W:0
| | 126-162| Red/Green- R:255
G:- B:0
W:0
---|---|---|---
163| Red
R:255 G:0
B:0 W:0
164-200| Red/Blue+ R:255
G:0 B:+
W:0
201| Magenta R:255
G:0 B:255
W:0
202-238| Red-/Blue R:-
G:0 B:255
W:0
239| Blue R:0
G:0 B:255
W:0
240-247| Colour index, fast to slow
248-255| Colour snap, fast to slow
82| Plate foreground
dimmer
| 000-255| 0-100％
83| Plate background| 000-000| No function
001-002| White(2700K)
003-004| White(3200K)
005-006| White(4200K)
007-008| White(5600K)
009-010| White(8000K)
011| Blue R:0
G:0 B:255
W:0
012-048| Green+/Blue R:0
G:+ B:255
W:0
049| Cyan R:0
G:255 B:255 W:0
050-086| Green/Blue- R:0
G:255 B:-
W:0
087| Green R:0
G:255 B:0
W:0
| | 088-124| Red+/Green R:+
G:255 B:0
W:0
---|---|---|---
125| Yellow R:255
G:255 B:0
W:0
126-162| Red/Green- R:255
G:- B:0
W:0
163| Red
R:255 G:0
B:0 W:0
164-200
| Red/Blue+ R:255
G:0 B:+
W:0
201
| Magenta R:255
G:0 B:255
W:0
202-238
| Red-/Blue R:-
G:0 B:255
W:0
239
| Blue R:0
G:0 B:255
W:0
240-247| Color index,fast to slow
248-255| Color snap,fast to slow
84| Plate background
dimmer
| 000-255| 0-100％
85
| Plate 1(pixels 1-7)| 000-002| Plate FX All select(all on) see Plate
Patterns
FX select
(see Pixel Mapping)
| 003-255
86| Plate 1(pixels 1-7) FX movement speed
＆ direction
(see Pixel Mapping)
| 000-005| No function
006-124| Left to right, fast to slow
125-130| No function
131-249| Right to left, slow to fast
250-255| No function
87| Plate 1(pixels 1-7)| 000-002| Snap from cell to cell
FX crossfade (see Pixel Mapping)| 003-255| Fade duration: short to
long
88| Plate 2(pixels 8-14)| 000-002| Plate FX All select(all on) see
Plate Patterns
FX select (see Pixel Mapping)| 003-255
89| Plate 2(pixels 8-14)| 000-005| No function
| FX movement speed ＆ direction (see Pixel Mapping)| 006-124|
Left to right, fast to slow
---|---|---|---
125-130| No function
131-249| Right to left, slow to fast
250-255| No function
90| Plate 2(pixels 8-14)| 000-002| Snap from cell to cell
FX crossfade (see Pixel Mapping)| 003-255| Fade duration: short to
long
91| Beam 1(pixels 1-14)| 000-002| Beam FX All select(all on) see
Beam Patterns
FX select (see Pixel Mapping)| 003-255
92
| Beam 1(pixels 1-14) FX movement speed
＆ direction
(see Pixel Mapping)
| 000-005| No function
006-124| Left to right, fast to slow
125-130| No function
131-249| Right to left, slow to fast
250-255| No function
93
| Beam 1(pixels 1-14)| 000-002| Snap from cell to cell
Fade duration: short to long
FX crossfade (see Pixel Mapping)| 003-255
94
| Beam 2(pixels 15-28) FX select (see Pixel Mapping)| 000-002|
Beam FX All select(all on) see Beam Patterns
003-255
95| Beam 2(pixels 15-28)FX movement speed ＆ direction (see
Pixel Mapping)| 000-005| No function
006-124| Left to right, fast to slow
125-130| No function
131-249| Right to left, slow to fast
250-255| No function
96| Beam 2(pixels 15-28) FX crossfade (see Pixel Mapping)|
000-002| Snap from cell to cell
Fade duration: short to long
003-255
97| **Control*| 000-005| No function
006-010| Off (dimmer mode)
011-015| Dimmer 1
016-020| Dimmer 2
021-025| Dimmer 3
026-030| 600 Hz
031-035| 1200 Hz
036-040| 2000 Hz
041-045| 4000 Hz
046-050| 6000 Hz
051-055| 25 KHz
056-060| Fan mode auto
060-065| Fan mode on
066-070| Tilt reset
| | 071-075| Plate 1 invert off
---|---|---|---
076-080| Plate 1 invert on
081-085| Plate 2 invert off
086-090| Plate 2 invert on
091-095| Beam 1 invert off
096-100| Beam 1 invert on
101-105| Beam 2 invert off
106-110| Beam 2 invert on
111-115| Plate swap on
116-120| Plate swap off
121-125| Beam swap on
126-130| Beam swap off
131-255| No function
| | |
74CH| | |
Channel| Function| Value| Percent/Setting
1| Tilt| 000-255| 0-100％
2| Fine tilt| 000-255| 0-100％
3| Dimmer| 000-255| 0-100％
4| Strobe| 000-009| Open
010-079| Strobe, slow to fast
080-149| Pulse, slow to fast
150-219| Random Strobe, slow to fast
220-255| Open
5| Plate pixel 1 red| 000-255| 0-100％
6| Plate pixel 1 green| 000-255| 0-100％
7| Plate pixel 1 blue| 000-255| 0-100％
8| Plate pixel 2 red| 000-255| 0-100％
9| Plate pixel 2 green| 000-255| 0-100％
10| Plate pixel 2 blue| 000-255| 0-100％
11| Plate pixel 3 red| 000-255| 0-100％
12| Plate pixel 3 green| 000-255| 0-100％
13| Plate pixel 3 blue| 000-255| 0-100％
14| Plate pixel 4 red| 000-255| 0-100％
15| Plate pixel 4 green| 000-255| 0-100％
16| Plate pixel 4 blue| 000-255| 0-100％
17| Plate pixel 5 red| 000-255| 0-100％
18| Plate pixel 5 green| 000-255| 0-100％
19| Plate pixel 5 blue| 000-255| 0-100％
20| Plate pixel 6 red| 000-255| 0-100％
21| Plate pixel 6 green| 000-255| 0-100％
22| Plate pixel 6 blue| 000-255| 0-100％
23| Plate pixel 7 red| 000-255| 0-100％
24| Plate pixel 7 green| 000-255| 0-100％
---|---|---|---
25| Plate pixel 7 blue| 000-255| 0-100％
26| Plate pixel 8 red| 000-255| 0-100％
27| Plate pixel 8 green| 000-255| 0-100％
28| Plate pixel 8 blue| 000-255| 0-100％
29| Plate pixel 9 red| 000-255| 0-100％
30| Plate pixel 9 green| 000-255| 0-100％
31| Plate pixel 9 blue| 000-255| 0-100％
32| Plate pixel 10 red| 000-255| 0-100％
33| Plate pixel 10 green| 000-255| 0-100％
34| Plate pixel 10 blue| 000-255| 0-100％
35| Plate pixel 11 red| 000-255| 0-100％
36| Plate pixel 11 green| 000-255| 0-100％
37| Plate pixel 11 blue| 000-255| 0-100％
38| Plate pixel 12 red| 000-255| 0-100％
39| Plate pixel 12 green| 000-255| 0-100％
40| Plate pixel 12 blue| 000-255| 0-100％
41| Plate pixel 13red| 000-255| 0-100％
42| Plate pixel 13 green| 000-255| 0-100％
43| Plate pixel 13 blue| 000-255| 0-100％
44| Plate pixel 14 red| 000-255| 0-100％
45| Plate pixel 14 green| 000-255| 0-100％
46| Plate pixel 14 blue| 000-255| 0-100％
47| Beam pixel 1| 000-255| 0-100％
48| Beam pixel 2| 000-255| 0-100％
49| Beam pixel 3| 000-255| 0-100％
50| Beam pixel 4| 000-255| 0-100％
51| Beam pixel 5| 000-255| 0-100％
52| Beam pixel 6| 000-255| 0-100％
53| Beam pixel 7| 000-255| 0-100％
54| Beam pixel 8| 000-255| 0-100％
55| Beam pixel 9| 000-255| 0-100％
56| Beam pixel 10| 000-255| 0-100％
57| Beam pixel 11| 000-255| 0-100％
58| Beam pixel 12| 000-255| 0-100％
59| Beam pixel 13| 000-255| 0-100％
60| Beam pixel 14| 000-255| 0-100％
61| Beam pixel 15| 000-255| 0-100％
62| Beam pixel 16| 000-255| 0-100％
63| Beam pixel 17| 000-255| 0-100％
64| Beam pixel 18| 000-255| 0-100％
65| Beam pixel 19| 000-255| 0-100％
66| Beam pixel 20| 000-255| 0-100％
67| Beam pixel 21| 000-255| 0-100％
---|---|---|---
68| Beam pixel 22| 000-255| 0-100％
69| Beam pixel 23| 000-255| 0-100％
70| Beam pixel 24| 000-255| 0-100％
71| Beam pixel 25| 000-255| 0-100％
72| Beam pixel 26| 000-255| 0-100％
73| Beam pixel 27| 000-255| 0-100％
74| Beam pixel 28| 000-255| 0-100％
| | |
30CH| | |
Channel| Function| Value| Percent/Setting
1| Tilt| 000-255| 0-100％
2| Fine tilt| 000-255| 0-100％
3| Master dimmer| 000-255| 0-100％
4| Plate dimmer| 000-255| 0-100％
5| Beam dimmer| 000-255| 0-100％
6| Plate flash duration**|
000-009
| Classic shutter mode: disables duration control
010-250| Slow to fast
251-255| 100％On, no flash/strobe
7| Plate flash rate| 000-009| 100%
010-250| Slow to fast
251-255| 100%
8| Beam flash duration|
000-009
| Classic shutter mode: disables duration
control
010-250| Slow to fast
251-255| 100％On, no flash/strobe
9| Beam flash rate| 000-009| 100%
010-250| Slow to fast
251-255| 100%
10| Plates red| 000-255| 0-100％
11| Plates green| 000-255| 0-100％
12| Plates blue| 000-255| 0-100％
13| Beam FX| 000-005| No function
006-042| Ramp up
043-085| Ramp down
086-128| Ramp up-down
129-171| Random
172-214| Lightning
215-255| Spikes
14| Plates foreground| 000-000| No function
| | 001-002| White(2700K)
---|---|---|---
003-004| White(3200K)
005-006| White(4200K)
007-008| White(5600K)
009-010| White(8000K)
011| Blue R:0
G:0 B:255
W:0
012-048
| Green+/Blue R:0
G:+ B:255
W:0
049
| Cyan R:0
G:255 B:255 W:0
050-086
| Green/Blue- R:0
G:255 B:-
W:0
087
| Green R:0
G:255 B:0
W:0
088-124
| Red+/Green R:+
G:255 B:0
W:0
125
| Yellow R:255
G:255 B:0
W:0
126-162
| Red/Green- R:255
G:- B:0
W:0
163
| Red
R:255 G:0
B:0 W:0
164-200
| Red/Blue+ R:255
G:0 B:+
W:0
201
| Magenta R:255
G:0 B:255
W:0
202-238
| Red-/Blue R:-
G:0 B:255
W:0
239
| Blue R:0
G:0 B:255
W:0
| 240-247 | Colour index, fast to slow | ||
|---|---|---|---|
| 248-255 | Colour snap, fast to slow | ||
| 15 | Plates foreground dimmer | 000-255 | 0-100％ |
| 16 | Plates background | 000-000 | No function |
| 001-002 | White(2700K) | ||
| 003-004 | White(3200K) | ||
| 005-006 | White(4200K) | ||
| 007-008 | White(5600K) | ||
| 009-010 | White(8000K) | ||
| 011 | Blue R:0 |
G:0 B:255
W:0
012-048| Green+/Blue R:0
G:+ B:255
W:0
049| Cyan R:0
G:255 B:255 W:0
050-086| Green/Blue- R:0
G:255 B:-
W:0
087| Green R:0
G:255 B:0
W:0
088-124| Red+/Green R:+
G:255 B:0
W:0
125| Yellow R:255
G:255 B:0
W:0
126-162| Red/Green- R:255
G:- B:0
W:0
163| Red
R:255 G:0
B:0 W:0
164-200| Red/Blue+ R:255
G:0 B:+
W:0
201| Magenta R:255
G:0 B:255
W:0
| | 202-238| Red-/Blue R:-
G:0 B:255
W:0
---|---|---|---
239
| Blue R:0
G:0 B:255
W:0
240-247| Colour index, fast to slow
248-255| Colour snap, fast to slow
17| Plates background dimmer| 000-255| 0-100％
18
| Plate 1(pixels 1-7)| 000-002| Plate FX All select(all on) see Plate
Patterns
FX select (see Pixel Mapping)| 003-255
19| Plate 1(pixels 1-7) FX movement speed
＆ direction (see Pixel Mapping)
| 000-005| No function
006-124| Left to right, fast to slow
125-130| No function
131-249| Right to left, slow to fast
250-255| No function
20
| Plate 1(pixels 1-7)| 000-002| Snap from cell to cell
FX crossfade
(see Pixel Mapping)
| 003-255| Fade duration:short to long
21
| Plate 2(pixels 8-14)| 000-002| Plate FX All select(all on) see Plate
Patterns
FX select
(see Pixel Mapping)
| 003-255
22
| Plate 2(pixels 8-14) FX movement speed
＆ direction
(see Pixel Mapping)
| 000-005| No function
006-124| Left to right, fast to slow
125-130| No function
131-249| Right to left,slow to fast
250-255| No function
23
| Plate 2(pixels 8-14)| 000-002| Snap from cell to cell
FX crossfade
(see Pixel Mapping)
| 003-255| Fade duration:short to long
24
| Beam 1(pixels 1-14)| 000-002| Beam FX All select(all on) see Beam
Patterns
FX select
(see Pixel Mapping)
| 003-255
25
| Beam 1(pixels 1-14) FX movement speed
＆ direction
(see Pixel Mapping)
| 000-005| No function
006-124| Left to right,fast to slow
125-130| No function
131-249| Right to left, slow to fast
250-255| No function
26
| Beam 1(pixels 1-14)| 000-002| Snap from cell to cell
Fade duration: short to long
FX crossfade
(see Pixel Mapping)
| 003-255
27
| Beam 2(pixels 15-28)
FX select
(see Pixel Mapping)
| 000-002| Beam FX All select(all on) see Beam Patterns
---|---|---|---
003-255
28
| Beam 2(pixels
15-28)FX movement speed ＆ direction (see Pixel Mapping)
| 000-005| No function
006-124| Left to right, fast to slow
125-130| No function
131-249| Right to left, slow to fast
250-255| No function
29
| Beam 2(pixels 15-28)
FX crossfade
(see Pixel Mapping)
| 000-002| Snap from cell to cell
Fade duration:short to long
003-255
30
|
**Control***
| 000-005| No function
006-010| Off (dimmer mode)
011-015| Dimmer 1
016-020| Dimmer 2
021-025| Dimmer 3
026-030| 600 Hz
031-035| 1200 Hz
036-040| 2000 Hz
041-045| 4000 Hz
046-050| 6000 Hz
051-055| 25 KHz
056-060| Fan mode auto
060-065| Fan mode on
066-070| Tilt reset
071-075| Plate 1 invert off
076-080| Plate 1 invert on
081-085| Plate 2 invert off
086-090| Plate 2 invert on
091-095| Beam 1 invert off
096-100| Beam 1 invert on
101-105| Beam 2 invert off
106-110| Beam 2 invert on
111-115| Plate swap on
116-120| Plate swap off
121-125| Beam swap on
126-130| Beam swap off
131-255| No function
| | |
24CH| | |
Channel| Function| Value| Percent/Setting
1| Tilt| 000-255| 0-100％
2| Fine tilt| 000-255| 0-100％
3| Master dimmer| 000-255| 0-100％
---|---|---|---
4| Plate dimmer| 000-255| 0-100％
5| Beam dimmer| 000-255| 0-100％
6
|
Plate flash duration
|
000-009
| Classic shutter mode:disables duration
control
010-250| Slow to fast
251-255| 100％On,no flash/strobe
7
|
Plate flash rate
| 000-009| 100%
010-250| Slow to fast
251-255| 100%
8
|
Beam flash duration
|
000-009
| Classic shutter mode:disables duration
control
010-250| Slow to fast
251-255| 100％On,no flash/strobe
9
|
Beam flash rate
| 000-009| 100%
010-250| Slow to fast
251-255| 100%
10| Plates red| 000-255| 0-100％
11| Plates green| 000-255| 0-100％
12| Plates blue| 000-255| 0-100％
13
|
Beam FX
| 000-005| No function
006-042| Ramp up
043-085| Ramp down
086-128| Ramp up-down
129-171| Random
172-214| Lightning
215-255| Spikes
14
|
Plates foreground
| 000-000| No function
001-002| White(2700K)
003-004| White(3200K)
005-006| White(4200K)
007-008| White(5600K)
009-010| White(8000K)
011
| Blue R:0
G:0 B:255
W:0
012-048
| Green+/Blue R:0
G:+ B:255
W:0
049| Cyan R:0
G:255 B:255
| W:0 |
|---|
050-086
| Green/Blue- R:0
G:255 B:-
W:0
087
| Green R:0
G:255 B:0
W:0
088-124
| Red+/Green R:+
G:255 B:0
W:0
125
| Yellow R:255
G:255 B:0
W:0
126-162
| Red/Green- R:255
G:- B:0
W:0
163
| Red
R:255 G:0
B:0 W:0
164-200
| Red/Blue+ R:255
G:0 B:+
W:0
201
| Magenta R:255
G:0 B:255
W:0
202-238
| Red-/Blue R:-
G:0 B:255
W:0
239
| Blue R:0
G:0 B:255
W:0
240-247| Color index,fast to slow
248-255| Color snap,fast to slow
15| Plates foreground
dimmer
| 000-255| 0-100％
16
|
Plates background
| 000-000| No function
001-002| White(2700K)
003-004| White(3200K)
005-006| White(4200K)
007-008| White(5600K)
009-010| White(8000K)
011| Blue R:0
G:0 B:255
| W:0 |
|---|
012-048
| Green+/Blue R:0
G:+ B:255
W:0
049
| Cyan R:0
G:255 B:255 W:0
050-086
| Green/Blue- R:0
G:255 B:-
W:0
087
| Green R:0
G:255 B:0
W:0
088-124
| Red+/Green R:+
G:255 B:0
W:0
125
| Yellow R:255
G:255 B:0
W:0
126-162
| Red/Green- R:255
G:- B:0
W:0
163
| Red
R:255 G:0
B:0 W:0
164-200
| Red/Blue+ R:255
G:0 B:+
W:0
201
| Magenta R:255
G:0 B:255
W:0
202-238
| Red-/Blue R:-
G:0 B:255
W:0
239
| Blue R:0
G:0 B:255
W:0
240-247| Color index,fast to slow
248-255| Color snap,fast to slow
17| Plates background
dimmer
| 000-255| 0-100％
18| Plates 1 ＆2| 000-002| Plate FX All select(all on)
| FX select
(see Pixel Mapping)
| 003-255| see Plate Patterns
---|---|---|---
19
| Plates 1 ＆2
FX movement speed
＆ direction
(see Pixel Mapping)
| 000-005| No function
006-124| Left to right,fast to slow
125-130| No function
131-249| Right to left,slow to fast
250-255| No function
20
| Plates 1 ＆2| 000-002| Snap from cell to cell
FX crossfade
(see Pixel Mapping)
| 003-255| Fade duration:short to long
21
| Beams 1 ＆2| 000-002| Beam FX All select(all on) see Beam Patterns
FX select
(see Pixel Mapping)
| 003-255
22
| Beams 1 ＆2
FX movement speed
＆ direction
(see Pixel Mapping)
| 000-005| No function
006-124| Left to right,fast to slow
125-130| No function
131-249| Right to left,slow to fast
250-255| No function
23
| Beams 1 ＆2| 000-002| Snap from cell to cell
Fade duration:short to long
FX crossfade
(see Pixel Mapping)
| 003-255
24
|
**Control***
| 000-005| No function
006-010| Off (dimmer mode)
011-015| Dimmer 1
016-020| Dimmer 2
021-025| Dimmer 3
026-030| 600 Hz
031-035| 1200 Hz
036-040| 2000 Hz
041-045| 4000 Hz
046-050| 6000 Hz
051-055| 25 KHz
056-060| Fan mode auto
060-065| Fan mode on
066-070| Tilt reset
071-075| Plate 1 invert off
076-080| Plate 1 invert on
081-085| Plate 2 invert off
086-090| Plate 2 invert on
091-095| Beam 1 invert off
096-100| Beam 1 invert on
101-105| Beam 2 invert off
106-110| Beam 2 invert on
| | 111-115| Plate swap on
---|---|---|---
116-120| Plate swap off
121-125| Beam swap on
126-130| Beam swap off
131-255| No function
| | |
13CH| | |
Channel| Function| Value| Percent/Setting
1| Tilt| 000-255| 0-100％
2| Fine tilt| 000-255| 0-100％
3| Plate dimmer| 000-255| 0-100％
4| Beam dimmer| 000-255| 0-100％
5
|
Plate flash duration
|
000-009
| Classic shutter mode: disables duration
control
010-250| Slow to fast
251-255| 100％On, no flash/strobe
6
|
Plate flash rate
| 000-009| 100%
010-250| Slow to fast
251-255| 100%
7
|
Beam flash duration
|
000-009
| Classic shutter
mode: disables duration control
010-250| Slow to fast
251-255| 100％On, no flash/strobe
8
|
Beam flash rate
| 000-009| 100%
010-250| Slow to fast
251-255| 100%
9| Plates red| 000-255| 0-100％
10| Plates green| 000-255| 0-100％
11| Plates blue| 000-255| 0-100％
12
|
Beam FX
| 000-005| No function
006-042| Ramp up
043-085| Ramp down
086-128| Ramp up-down
129-171| Random
172-214| Lightning
215-255| Spikes
13
|
**Control***
| 000-005| No function
006-010| Off (dimmer mode)
011-015| Dimmer 1
016-020| Dimmer 2
021-025| Dimmer 3
| | 026-030| 600 Hz
---|---|---|---
031-035| 1200 Hz
036-040| 2000 Hz
041-045| 4000 Hz
046-050| 6000 Hz
051-055| 25 KHz
056-060| Fan mode auto
060-065| Fan mode on
066-070| Tilt reset
071-075| Plate 1 invert off
076-080| Plate 1 invert on
081-085| Plate 2 invert off
086-090| Plate 2 invert on
091-095| Beam 1 invert off
096-100| Beam 1 invert on
101-105| Beam 2 invert off
106-110| Beam 2 invert on
111-115| Plate swap on
116-120| Plate swap off
121-125| Beam swap on
126-130| Beam swap off
131-255| No function
| | |
11CH| | |
Channel| Function| Value| Percent/Setting
1| Tilt| 000-255| 0-100％
2| Fine tilt| 000-255| 0-100％
3| Dimmer| 000-255| 0-100％
4
|
Plate flash duration
|
000-009
| Classic shutter mode:disables duration
control
010-250| Slow to fast
251-255| 100％On,no flash/strobe
5
|
Plate flash rate
| 000-009| 100%
010-250| Slow to fast
251-255| 100%
6
|
Beam flash duration
|
000-009
| Classic shutter
mode:disables duration control
010-250| Slow to fast
251-255| 100％On,no flash/strobe
7| Beam flash rate| 000-009| 100%
010-250| Slow to fast
| | 251-255| 100%
---|---|---|---
8| Plates red| 000-255| 0-100％
9| Plates green| 000-255| 0-100％
10| Plates blue| 000-255| 0-100％
11| Beam| 000-255| 0-100％
| | |
8CH| | |
Channel| Function| Value| Percent/Setting
1| Tilt| 000-255| 0-100％
2| Fine tilt| 000-255| 0-100％
3| Dimmer| 000-255| 0-100％
4
|
Strobe
| 000-009| Open
010-079| Strobe,slow to fast
080-149| Pulse,slow to fast
150-219| Random Strobe,slow to fast
220-255| Open
5| Red| 000-255| 0-100％
6| Green| 000-255| 0-100％
7| Blue| 000-255| 0-100％
8| Beam| 000-255| 0-100％
Troubleshooting
| Symptom | cause of issue | Approach |
|---|---|---|
| No menu displayed | 1. No AC input |
2. The switching power supply is damaged
3. Display board failure
| 1. Check the power supply line
2. Check whether the switching power supply has voltage output
3. Replace the display board
Can’t receive DMX signal| 1. The DMX signal line is faulty
2. The wiring sequence of the signal line is wrong
3. The IC receiving the signal at the signal input terminal is damaged
4. DMX address code setting and console
Corresponding controls do not match
5. Other parameters are set incorrectly
6. After entering the menu without pressing the confirm button
or MENU key to exit to the main
menu
|
1. Check or replace the signal line
2. Check the wiring sequence of the signal lines
3. Check the display board signal receiving IC and
Are the two resistors connected in series on the signal line open?
4. Check or reset the address code Or restore factory settings and try again
5. Press MENU to exit to the main menu
The surface temperature of the lamp body exceeds 75°
No temperature control protection
| 1. The thermistor on the lamp bead board is faulty
2. The temperature control circuit
on the display board is faulty
| 1. Replace the thermistor
2. Check the temperature control circuit on the motherboard
Uneven colour mixing Uneven colour spots| 1. Improper soldering of lamp beads
2. The lens or bracket is not
installed properly
| 1. Check the bulb welding condition
2. Check the lens assembly process and adjust the bracket assembly direction
The lamp bead is off or flickering a little| The lamp bead is damaged or the driver board has no current output| 1. Replace the lamp bead
2. Replace the damaged lamp beads
Or check the driver board circuit
3. Replace the corresponding driver IC
Parameters are not saved| Damaged IC for storing parameters| Replace memory IC
The whole light does not work| When the temperature is too high, the
temperature control protection will cause Switching the power supply over-
temperature protection does not work| Wait for the lamp body to cool down
before turning it on
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>