LANCOM 730-4G Shopping Malta Mediterranean Region Installation Guide
- June 1, 2024
- LANCOM
Table of Contents
lancom-systems.com
Quick Installation Guide
LANCOM 730-4G+
Interface overview of the LANCOM 730-4G+
Rear panel
- LTE / 4G antenna connectors
- Power supply connector
- Serial configuration interface
- Reset button
- Ethernet interface
- SIM card slot
Initial start-up
Establishing the required connections for device configuration
→ Alwaysobservetheadjacentsafetyinstructionsandnotes.
For the power supply select the description a), b) or c) applicable to the
equipment of the present device
a) Power supply via external power supply unit
Establish a power supply using the external power supply unit (if available).
b) PoE power supply via PoE network device
Connect a network cable to the Ethernet port marked PoE on the device and a
free PoEactive network socket on your local network (e. g. on a PoE-capable
switch)
c) PoE power supply via separate PoE injector
Connect a network cable to the Ethernet port marked PoE on the device and the
output of the PoE injector. Then connect another network cable to the input of
the PoE injector and a free NON-PoE-active network outlet of your local
network.
Connect the PoE injector to the power supply.
Always observe the documentation of the PoE injector or PoE switch!
→ Use suitable cables to connect other required device interfaces to other
components and, in the case of devices with Wi-Fi or mobile radio interfaces,
connect any antennas supplied.
→ Select one of the following configuration methads a} or b}.
a) Configuration via the local network (recommended)
Note that an active DHCP server is required in the network connected to the
device.
Connect the computer intended for configuration (e.g. notebook) either
directly via Ethernet cable to one of the ETH or LAN interfaces of the device,
or to a switch in the same network.
The possibly existing interface CONFIG or COM is not suitable for
configuration via the network!
b) Configuration via the serial interface of a connected computer (if
available)
You need a serial configuration cable which is connected to the possibly
existing CONFIG or COM interface of the device. This socket is exclusively
intended for connection to a serial interface!
Options for initial start-up of the unconfigured device
→ Option 1: via web browser (WEBconfig, not for serially connected devices)
Configuration via web browser is an easy and fast variant, since no additional
software is required on the computer used for configuration.
Note: If a certificate warning appears in your browser when trying to
connect to your device, there is a button or link on the displayed browser
page to connect to the device anyway (depending on the browser, usually under
Advanced).
In the following, select the description a) or b) that applies to your setup
for configuring the device.
a) Configuration in a network without active DHCP server
For configuration via TCP/IP, the IP address of the device in the local
network (LAN) is required. After power-on, an unconfigured LANCOM device first
checks whether a DHCP server is active in the LAN.
The device can be accessed from any computer with the Auto DHCP function
enabled using a web browser under the IP address 172.23.56.254.
The given IP address can be modified at any time.
b) Configuration in a network with active DHCP server
In this procedure, the DNS server used in your network must be able to
resolve the host name reported by the device via DHCP. When using a LANCOM
device as a DHCP and DNS server, this is the default case.
At https://lancom-XXYYZZ you can access your device.
Replace XXYYZZ with the last six digits of the MAC address of your device,
which you can find on the enclosed document LANCOM Management Cloud or on the
nameplate of the device. If necessary, append the domain name of your local
network (e.9..intern),
- When the computer is connected to an unconfigured LANCOM device, WEBconfig automatically starts the setup wizard Basic settings.
- After the setup wizard has been run through, the initial commissioning of the device is complete.
- If necessary, make further configurations using the setup wizards available for selection.
→ Option 2: via the Windows software LANconfig (www.lancom- systems.com/downloads)
- Please wait until the booting process of the device is completed before starting LANconfig.
- Unconfigured LANCOM devices are automatically found by LANconfig in the local network (LAN) and the setup wizard Basic settings is then started.
- After the setup wizard has finished, the initial start-up of the device is complete.
- If necessary, make further configurations using the setup wizards available for selection.
→ Option 3: via the LANCOM Management Cloud (LMC)
The LMC is not required for the operation of LANCOM devices, but it
facilitates their commissioning and permanent management through centralized,
automated management. Special requirements are necessary to configure the
device via the LMC. Information on this topic can be found at www.lancom-
systems.com/lmc-access.
General safety instructions
→ Under no circumstances should the device housing be opened and the device
repaired without authorization. Any device with a case that has been opened is
excluded from the warranty.
→ If antennas are available, they may only be installed or replaced when the
device is switched off. Mounting or demounting antennas while the device is
powered on may cause the destruction of the radio module.
→ Mounting, installation, and commissioning of the device may only be carried
out by qualified personnel.
Safety instructions and intended use
In order to avoid harming yourself, third parties or your equipment when
installing your LANCOM device, please observe the following safety
instructions. Operate the device only as described in the corresponding
documentation. Pay particular attention to all warnings and safety
instructions. Use only those third-party devices and components that are
recommended or approved by LANCOM Systems. Before commissioning the device, be
sure to study the corresponding Hardware Quick Reference which can be
downloaded from the LANCOM website www.lancom-
systems.corn/downloads.
Any warranty and liability claims against LANCOM Systems are excluded in the
event of any use other than the intended use described below!
Environment
LANCOM devices should only be operated when the following environmental
requirements are met:
→ Ensure that you comply with the temperature and humidity ranges specified in
the Quick Reference Guide for the LANCOM device.
→ Do not expose the device to direct sunlight (does not apply to outdoor
devices).
→ Ensure that there is adequate air circulation and do not obstruct the
ventilation slots.
→ Do not cover devices or stack them on top of one another
→ The device must be mounted so that it is freely accessible (for example, it
should be accessible without the use of technical aids such as elevating
platforms (does not apply to outdoor devices)); a permanent installation (e.
g. under plaster) is not permitted. → → Only outdoor equipment intended for
this purpose is to be operated outdoors.
→ When operating an outdoor device without a suitable surge protection
adapter, LANCOM does not provide any warranty in case of surge damage.
Power supply
Before start-up, the following points must be observed, as improper use can
lead to personal injury and damage to property, as well as voiding the
warranty:
→ If available, the power plug of the device must be freely accessible.
→Operate the device only with a professionally installed power supply at a
nearby and at all times freely accessible socket.
→ Only use the enclosed power supply / IEC cable or the one listed in the
hardware quick reference.
→A high touch current is possible for devices with metal housing and grounding
screw! Before connecting the power supply, connect the grounding screw to a
suitable ground potential.
→ Some devices support power supply via an Ethernet cable (Power over Ethernet
– PoE). Please refer to the corresponding notes in the hardware quick
reference of the device.
→ Never operate damaged components.
→ Only switch on the device when the housing is closed.
→ The device must not be installed during thunderstorms and should be
disconnected from the power supply during thunderstorms.
→ In case of emergency (e. g. damage, ingress of liquids or objects, for
example through the ventilation slots), disconnect the power supply
immediately.
Applications
→ The devices may only be used in accordance with the relevant national
requiations and under consideration of the legal situation applicable there.
→ The devices must not be used for the actuation, control, and data
transmission of machinery that, in case of malfunction or failure, may present
a danger to life and limb, nor for the operation of critical infrastructures.
→ The devices with their respective software are not designed, intended or
certified for use in: the operation of weapons, weapons systems, nuciear
facilities, mass transportation, autonomous vehicles, aircraft, life support
computers or equipment (including resuscitators and surgical implants),
pollution control, hazardous materiais management, or other hazardous
applications where failure of the device or software could lead to a situation
in which personal injury or death could result. The customer is aware that the
use of the devices or software in such applications is entirely at the
customer’s tisk.
Regulatory Notice
Regulatory compliance for devices with radio or Wi-Fi interfaces
This LANCOM device is subject to governmental regulation. The user is
responsible for ensuring that this device operates in accordance with local
regulatory guidelines, specifically for compliance with potential channel
restrictions.
Channel restrictions in Wi-Fi operation for devices with Wi-Fi interfaces
When operating this radio equipment in EU countries the frequency range 5,150
– 5,350 MHz (Wi-Fi channels 36 – 64) as well as the frequency range 5,945 –
6,425 MHz (Wi-Fi channels 1 – 93) is limited to indoor use.
Maximum transmission power for devices with radio interfaces
This LANCOM device may contain one or more radio interfaces using various
technologies. The maximum output power per technology and used frequency band
for use in EU countries is described in the following tables:
Declarations of Conformity
You will find all the Declarations of Conformity concerning our product
portfolio under www.lancom-systems.com/doc.
These documents contain all the tested standards and required guidelines in
the area of EMC – SAFETY – RF, as well as the proof of the guidelines
concerning RoHS & REACH.
Simplified Declaration of Conformity
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen,
declares that this device is in compliance with Directives 2014/30/EU,
2014/35/EU, 2014/53/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The
full text of the EU Declaration of Conformity is available at the following
Internet address: www.lancom-systems.com/doc
Documentation / Firmware
Basically, current versions of the LCOS firmware, drivers, tools and
documentatiofor all LANCOM and AirLancer products are available for download
free of charge from our website.
Detailed documentation for your devicecan be found in the download portal of
tLANCOM website: www.lancom-systems.com/downloads
You will also find explanations of all the functions of your LANCOM device in
theLCOS Reference Manual: www.lancom-
systems.de/docs/LCOS/Refmanual/EN/
Service & Support
The LANCOM Knowledge Base — with over 2,500 articles — is available to you at
any time via the LANCOM website: www.lancom-
systems.com/knowledgebase
If you have any further questions, please submit your request via our Service
& Support portal: www.lancom-systems.com/service-support
Information on the lifecycle, in particular on End of Sale / End of Life and
on the supply of LANCOM devices with security updates can be found at: www
.lancom-systems.com/lifecycle
All information on your device
https://www.lancom-systems.com/products/routers-sd-wan/internet-access- routers/lancom-730-4gplus
Technical data (excerpt)
Hardware|
---|---
Power supply| 12 V DC, external power adapter or PoE according to 802.3af/at
via ETH 1 For an overview of the power supplies compatible with your device,
see www.lancom-systems.com/kb/power-supplies.
Housing| Robust synthetic housing, rear connectors, ready for wall mounting,
Kensington lock; dimensions 210 x 45 x 140 mm (W x H x D)
Package contents|
Cables| 1 Ethernet cable, 3m
Antennas| Two LTE / 4G antennas for LTE, HSPA+, HSxPA, UMTS
Power adapter| External power adapter
LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are
registered trademarks. All other names or descriptions used may be trademarks
or registered trademarks of their owners. This document contains statements
relating to future products and their attributes. LANCOM Systems reserves the
right to change these without notice. No liability for technical errors and /
or omissions.
112356/0124
References
- Business network solutions "engineered in Germany": LANCOM Systems GmbH
- Business network solutions "engineered in Germany": LANCOM Systems GmbH
- Confluence Mobile - LANCOM Wissensdatenbank
- Confluence Mobile - LANCOM Wissensdatenbank
- LCOS 10.80 Reference Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>