LANCOM LX-6500E Wi-Fi 6E and Digital Signage Installation Guide
- June 1, 2024
- LANCOM
Table of Contents
LANCOM LX-6500E Wi-Fi 6E and Digital Signage
Overview
This guide provides quick installation instructions for the LANCOM LX-6500E. For further documentation and firmware updates, please visit lancom- systems.de.
Specifications
- 2.5G Config (Com) Reset DC 12 V
- ETH1 (PoE) and ETH2 interfaces
- USB interface
- Serial configuration interface
- Reset button
- Power supply via external power adapter
| Feature | Description |
|---|---|
| Power Supply | External power adapter or PoE |
| Connectivity Ports | 2.5G, Config (Com), Reset, DC 12 V, USB, ETH1 (PoE), ETH2 |
| Mounting Equipment | Included for wall and deck mounting |
Technology and Frequency Range
| Technology | Frequency Range (MHz) | Max. Transmission Power (dBm EIRP) |
|---|---|---|
| WLAN | 20, 30 | 23 |
| SRD / BLE / SRD / ESL (ePaper) | 10 | 14 / 25 mW |
Product Usage Instructions
Initial Setup:
- Power Supply: Connect the external power supply to establish power.
- PoE Power Supply: Connect a network cable to the Ethernet port labeled with PoE from a PoE-enabled network port in your local network.
- PoE Power Supply Note: Refer to the documentation of your PoE injector or PoE switch for specific instructions.
General Safety Guidelines:
Installation and setup should be carried out only by qualified personnel.
Environment:
Ensure compliance with specified humidity levels.
Regulatory Compliance:
Adhere to relevant EMV, safety, and wireless regulations, including RoHS & REACH directives.
Technology:
- Frequency Range: WLAN 20MHz, SRD / BLE / SRD / ESL (Paper) 10MHz
- Max Transmit Power: WLAN 20dBm EIRP, SRD / BLE / SRD / ESL (ePaper) 14 / 25 mW
Connectivity and Ports
- 2.5G Ethernet Ports (ETH1 with PoE, ETH2)
- Config (Com) Reset Button
- DC 12 V Power Socket
- USB Interface
Technical Specifications (Excerpt)
Hardware Power Supply
Provided by an external power adapter or through PoE (Power over Ethernet).
Included in Delivery
- Ethernet Cable, 3m. For more information, visit www.lancom.de/mi-wm-lx-6500.
- Mounting Equipment
Initial Operation
- Connect the external power adapter to establish a power supply.
- For PoE power supply, connect a network cable to the PoE-labeled Ethernet port of a PoE-active network socket in your local network (e.g., at a PoE injector or PoE switch).
Note: Always refer to the documentation of the PoE injector or PoE switch for detailed instructions.
FAQs
- Q: Can the LANCOM LX-6500E be powered through PoE?
- A: Yes, the LANCOM LX-6500E supports PoE power supply through the designated Ethernet port.
- Q: What are the recommended humidity levels for operating the LANCOM LX-6500E?
- A: It is recommended to operate the LANCOM LX-6500E within specified humidity ranges for optimal performance and longevity of the device.
- Q: Where can I find the full documentation and firmware updates?
- A: Visit the LANCOM Systems website at www.lancom.de/downloads for downloads and updates.
- Q: How can I power the LANCOM LX-6500E?
- A: The device can be powered using the included external power adapter or through a PoE-enabled network port.
- Q: What safety precautions should I take during installation?
- A: Ensure that installation and commissioning are performed by qualified personnel, and always follow the environmental and power supply guidelines.
Additional Resources
- LANCOM Power Supplies Knowledge Base
- LANCOM Knowledge Base (Confluence Mobile)
- Lifecycle Management at LANCOM Systems GmbH
- Service & Support at LANCOM Systems GmbH
“`
References
- DoC - LANCOM Systems GmbH
- Search - LANCOM Wissensdatenbank
- Confluence Mobile - LANCOM Wissensdatenbank