VITEK VT-8262 Men Shaver Instruction Manual

: June 10, 2024
: VITEK

VITEK VT-8262 Men Shaver

VT-8262 Men Shaver

DESCRIPTION

Description

Protection cap
Shaving heads
Detachable part of the shaving block
Detachable body of the shaving block
Body
On/off button
Locking mode on indicator
Operation/battery charging indicator
USB cord connection socket
Cleaning brush
USB cor
Power supply unit

SAFETY MEASURES

Before using the unit, thoroughly read through this instruction manual and keep it for future reference.
Use the unit for the intended purposes only as specified in this manual. Mishandling the unit can lead to its breakage, harm the user or damage his/her property

Before charging the battery for the first time, make sure that the voltage in your mains corresponds to power supply unit voltage.
Use the unit only with the power supply unit supplied.
Use the men shaver only for the intended purposes.
Do not leave the operating unit unattended.
Switch the shaver off during pauses in operation or when you are not using it.
Do not charge the unit in places with high humidity and temperature.
Charge the battery at the temperature from 0°C to +35°C and relative humidity not more than 80%.
Only use the USB cord (11) supplied with the unit to charge the shaver.
Do not place the power supply unit near hot surfaces or open flame.
Do not immerse the shaver, power supply unit, USB cable into water or any other liquids.
To avoid injury do not use the shaver with damaged stationary shaving head nets or rotating blades.
For child safety reasons do not leave polyethylene bags used as packaging unattended.

Attention! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

This unit is not intended for usage by children.
Do not leave children unattended to avoid them using the unit as a toy
During operation and breaks between operation cycles, the unit should be placed out of reach of children.
The unit is not intended to be used by people with physical, sensory or mental disabilities (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
Do not attempt to repair the unit. Do not disassemble the unit by yourself, if any malfunction is detected or after it was dropped, unplug the unit and apply to any authorized service center at the contact addresses given in the warranty certificate and on the website www.vitek.ru.
Transport the unit in the original package only.
Keep the unit out of reach of children and disabled persons.

THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY. ITS COMMERCIAL USAGE AND USAGE IN PRODUCTION AREAS AND WORK SPACES IS PROHIBITED.

USING OF MEN SHAVER

After unit transportation or storage at low temperature keep it for at least three hours at room temperature before switching on.

Battery charging

Before using the shaver for the first time or after a long period of inactivity the battery needs to be charged for 10 hours.

Connect the shaver to the power adapter (12) using the USB cord (11), the charging indicator (8) will start flashing.
After charging is finished the indicator (8) will glow constantly.
Battery recharging cycles should not exceed eight hours.

Notes:

Recharge the battery only after its full discharge.
Charge the battery at the temperature from 0°C to +35°C.
If you haven’t used the shaver for a month or longer, fully charge it before use.

Shaving block (3) removal and installation (fig. 1)

Using Of Men Shaver

Press the button to open the shaving block.
Pull upwards to detach the shaving block removable part (3).
Insert the removable part (3) back into the shaving block body (4).

Shaving heads (2) removal (fig. 2)

Using Of Men Shaver

Turn the shaving block (3) clamping frame knob counterclockwise.
Detach the clamping frame from the shaving heads blades (2).
Remove the blade from the shaving head mesh (2).

Shaving heads (2) installation (fig. 3)

Using Of Men Shaver

Match the groove A on the mesh with the ledge B on the shaving block (3) and insert it.
Match the grooves C on the clamping frame with the ledges D on the shaving block and insert the clamping frame.
Turn the knob on the clamping frame clockwise for locking.

USAGE

ATTENTION!
Do not use the shaver with a damaged shaving block (3) or shaving heads (2).

Remove the protection cap (1).
Switch the shaver on by pressing the on/off button (6), the on/off indicator (8) will light up.
Touching the skin slightly, move the shaving block back and forth and rotationally at the same time.
After shaving switch the shaver off by pressing the on/off button (6), cover the shaving heads (2) with the protection cap
(1) and take the shaver away for storage.

Locking mode

The shaver locking mode is intended for protection from accidental switching on.

To switch the locking mode on, press and hold the on/off button (6) for 3 seconds, the locking mode indicator (7) will confirm the mode switching on with a red signal and will go out.
To switch the locking mode off, press and hold the on/off button (6) for 3 seconds, the shaver will immediately start operating.

CLEANING AND MAINTENANCE

For an optimum performance, clean the shaving block after each use or after several shaving cycles.

Switch the shaver off by pressing the on/off button (6), the operation indicator (8) will go out.
To make the shaving heads cleaning easy, remove the shaving block from the shaver body (5) by pulling its body (4) upwards.
Press the button to open the shaving block and detach the removable part (3) (fig. 1).

You can find the shaving block (3) removal and installation procedure in the corresponding section above

Using a brush (10), clean the shaving block and the shaving heads (2) both from the inside and the outside, and clean the blades drive (fig. 4).
After brushing the bristles off, you can rinse both parts of the shaving block (3, 4) and the shaving heads (2) with warm water (fig. 5, 6).
After rinsing, dry or wipe all parts dry with a cloth to keep the shaving heads dry.
Insert the removable part (3) back into the shaving block body (4) and close the shaving block.
Install the shaving block back to its place, preliminarily matching the ledge on the shaving block body (4) with the groove in the installation place on the shaver body (5).
Put the protective cap (1) on the shaving heads (2).
Wipe the shaver body with a soft, slightly damp cloth and then wipe it dry.
Do not use metal brushes and abrasive detergents or solvents for cleaning.
It is recommended to clean the shaving head blades (2) every two months.

You can find the shaving heads (2) removal and installation procedure in the corresponding sections above

Switch the shaver off by pressing the on/off button (6), the operation indicator (8) will go out.
Press the button to open the shaving block and detach the removable part (3) (fig. 1).
Turn the frame lock counterclockwise and remove the frame (fig. 2).
Remove each fixed shaving head mesh together with the blade.
Carefully remove the blades from the fixed meshes

Note: Be careful when removing the fixed meshes, make sure that the rotating blades have been installed into the same meshes after cleaning, otherwise the noise may be higher and the shaving quality affected.

Clean the blades and the fixed meshes with a brush (10).
Install the fixed meshes in the shaving block (3) removable part making sure the meshes have been correctly installed.
Insert the blades into the fixed meshes following the instructions above.
Install the clamping frame, turn the frame lock clockwise until fixing.
Insert the removable part (3) back into the shaving block body (4) and close the shaving block.
Place the shaving block on the shaver body (5).
Put the protective cap (1) on the shaving heads (2).

Shaving heads lubrication

For an optimum shaver maintenance, lubricate each shaving head with a lubricant drop periodically, any shaver or clipper lubricant will be good. Apply a shaver lubricant on the outside of the shaving heads and rub slightly with your finger. After turning the shaver on for a short time, let the lubricant spread over the underside of the meshes and the rotating blades. The procedure takes less than a minute. Apply a lubricant as needed, for example, if you often rinse the shaving block with warm water, you need to lubricate it more frequently, almost after each rinsing. At any abnormal noise lubricate each shaving head mesh with a lubricant drop. Switch the shaver on and lubricate the outside of each mesh with a lubricant drop. Make sure the abnormal noise has disappeared and switch the shaver off. Remove excess lubricant with a cloth.
Attention! Use only a shaver or clipper lubricant. DO NOT use vegetable oil, grease or oil-solvent mixture for lubrication. Solvents tend to evaporate, whereupon the thick lubricant remains may slow down the blades rotation.

STORAGE

Before storing the shaver, clean and lubricate it according to the «Cleaning and Maintenance» section.
Wipe the shaver body with a soft, slightly damp cloth and then wipe it dry.
Do not use metal brushes and abrasive detergents or solvents for cleaning.
Put the protective cap (1) on the shaving heads (2).
Store the shaver in a cool dry place away from children.

ENVIRONMENTAL PROTECTION

The shaver is provided with a disposable battery. Before you throw away the inoperative shaver discharge the battery completely, remove it and dispose of it according to the hazardous waste disposal regulations of your country.
Do not throw away the shaver until you remove the builtin battery.

DELIVERY SET

Men shaver – 1 pc.
USB cord – 1 pc.
Protective cap – 1 pc.
Cleaning brush – 1 pc.
Power supply unit – 1 pc.
Manual – 1 pc.
Warranty certificate – 1 pc

TECHNICAL SPECIFICATIONS

Electric shaver

Power supply: 2,4 V, built-in rechargeable Ni-Mh
battery 600 mAh
Rated input power: 2 W
Input voltage: 5 V 1000 mA
Charging time: 8 hours
Continuous operation time: 60 minutes
IPX7

Power supply unit

Power supply: 100-240 V ~ 50 Hz 0,3 A
Output voltage: 5,0 V 1,0 А

Symbol The symbol indicates that the product is suitable for cleaning under running water.

RECYCLING

For environment protection do not throw out the unit and the batteries (if included), do not discard the unit and the batteries with usual household waste after the service life expiration; apply to specialized centers for further recycling.
The waste generated during the disposal of the unit is subject to mandatory collection and consequent disposal in the prescribed manner.
For further information about recycling of this product apply to a local municipal administration, a disposal service or to the shop where you purchased this product.

The manufacturer preserves the right to change design, structure and specifications not affecting general principles of the unit operation without a preliminary notification due to which insignificant differences between the manual and product may be observed. If the user reveals such differences, please report them via e-mail info@vitek.ru for receipt of an updated manual.

Unit operating life is 3 years

Guarantee

Details regarding guarantee conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee.

This product conforms to the EMC Directive 2014/30/ EU and to the Low Voltage Directive 2014/35/EU.

A production date of the item is indicated in the serial number on the technical data plate. A serial number is an eleven-unit number, with the first four figures indicating the production date. For example, serial number 0606ххххххх means that the item was manufactured in June (the sixth month) 2006

VITEK-Logo