goobay 58493 Digital Analog Converter Instruction Manual

: June 1, 2024
: goobay

Table of Contents

58493 Digital Analog Converter
Specifications
Symbols used
Safety instructions
Description and function
Intended use
Preparation
Connection and operation
Maintenance, Care, Storage and Transportation
Disposal instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

58493
Digital-to-Analogue Converter 192 kHz
Instruction Manual

58493 Digital Analog Converter

goobay 58493 Digital Analog Converter

Specifications

Item number	58493
Connectors – Inputs	Toslink socket, Coaxial socket, DC socket
Connectors – Outputs	3.5 mm jack socket, RCA jack (L/R)
Input	5.0 V ****, 1.0 A, 5.0 W
Supported Toslink & Coaxial audio formats	LPCM 2CH, Dobly Digital 2CH, DTS

Symbols used

Class II equipment| IEC 60417- 5172|
---|---|---
Class III equipment| IEC 60417- 5180|
Direct current| IEC 60417- 5031|
Alternating current| IEC 60417- 5032| ****
For indoor use only| IEC 60417- 5957| Icon

Safety instructions

The user manual is part of the product and contains important information for correct use.

Read the user manual completely and carefully before use.

The user manual must be available for uncertainties and passing the product.

Keep this user manual.

Notes for network separation
The product has no power switch and may be used only in easily accessible outlets to quickly remove it in an emergency and after use.
Voltage-free only with pulled plug.

In case of emergency, after use and during a thunderstorm, pull the mains plug out of the socket directly at the plug housing.
Do not open the housing.
Do not modify product and accessories.
Do not short-circuit connectors and circuits.

A defective device may not be put into operation, but must be disconnected from mains and protected against further use.

Use product, product parts and accessories only in perfect condition.
Avoid stresses such as heat and cold, moisture and direct sunlight, microwaves, vibrations and mechanical pressure.
In case of questions, defects, mechanical damage, trouble and other problems, non-recoverable by the documentation, contact your dealer or producer.

Not meant for children. The product is not a toy!

Secure packaging, small parts and insulation against accidental use.

Heat storage

Do not cover the product.
Keep enough space around all devices for a good ventlation and free motion and to avoid damages.

Description and function

2.1 Product
The product is a digital-to-analogue converter including power supply that converts digital input signals into analogue output signals.

2.2 Scope of delivery
Digital-to-Analogue Converter 192 kHz, Power supply, Charging cable, User Manual

2.3 Operating Elements
See Fig. 1.

Toslink socket
Coaxial socket
DC socket
3.5 mm jack socket
LED status indicator
RCA socket (R)
RCA socket (L)
USB-A socket
Euro plug
DC plug
USB-A plug

Intended use

This product is intended exclusively for private use and its intended purpose. This product is not intended for commercial use. We do not permit using the device in other ways like described in chapter „Description and Function“ or in the „Safety Instructions“. Use the product only in dry interior rooms. Not attending to these regulations and safety instructions might cause fatal accidents, injuries, and damages to persons and property.

Preparation

Check the scope of delivery for completeness and integrity.
Compare the specifications of all used devices and ensure compatibility.

Connection and operation

NOTICE! Material damage

Switch off all units to be connected and the converter before connecting or disconnecting the units via the connection sockets.

See Fig. 2.

Connect a source device to the Toslink socket (1) or coaxial socket (2) of the converter.
If two source devices are connected, the Toslink socket is active. Make sure that the input signal is digital, otherwise errors may occur.
Connect your output device to the 3.5 mm jack socket (4) or the RCA socket (6+7) of the converter.
Connection cables are not included in the delivery. Make sure that the source and output devices as well as the connection cables support the standards of the product!
Connect the USB-A plug (11) of the charging cable to the USB-A socket (9) of the power supply.
Plug the Euro plug (8) of the power supply into a free and easily accessible socket.
Connect the DC plug (10) of the charging cable to the DC socket (9) of the converter.
The converter is now supplied with power and the LED status indicator (3) lights up red.
Switch on the source and output devices.
After use, switch the source and output devices off again and disconnect all cable connections.

Maintenance, Care, Storage and Transportation

The product is maintenance-free.
NOTICE! Material damage

Always disconnect the mains plug before cleaning.
Only use a dry and soft cloth for cleaning.
Do not use detergents or chemicals.
Store the product out the reach of children and in a dry and dust-protected ambience when not in use.
Store cool and dry.
Keep and use the original packaging for transport.

Disposal instructions

**** According to the European WEEE directive, electrical and electronic equipment must not be disposed with consumers waste. Its components must be recycled or disposed apart from each other. Otherwise contaminative and hazardous substances can damage the health and pollute the environment.
As a consumer, you are committed by law to dispose electrical and electronic devices to the producer, the dealer, or public collecting points at the end of the devices lifetime for free. Particulars are regulated in national right. The symbol on the product, in the user manual, or at the packaging alludes to these terms. With this kind of waste separation, application, and waste disposal of used devices you achieve an important share to environmental protection.
WEEE No: 82898622

REV2023-12-15
V2.0aw
Subject to change without notice.
Goobay® by Wentronic GmbH | Pillmannstraße 12
38112 Braunschweig | Germany | cs@wentronic.com