PROJECT SOURCE 5742514 7 In Led Battery Operated Motion Sensing Flushmount Light Instruction Manual
- June 1, 2024
- PROJECT SOURCE
Table of Contents
PROJECT SOURCE 5742514 7 In Led Battery Operated Motion Sensing
Flushmount Light
PROJECT SOURCE and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.
Questions, problems, missing parts?
Before returning, contact us on:866-389-8827, 8 a.m. – 8 p.m., EST, Monday – Sunday or ascs@lowes.com.
Thank you for purchasing this PROJECT SOURCE product. We’ve created these easy-to-follow instructions to ensure you spend your time enjoying the product instead of putting it together. But, if you need more information than what is provided here, please visit Lowes.com, search the item number and refer to the Guides & Documents tab on the product’s page.
TROUBLESHOOTING
PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
---|
Light does not come on initially or no longer comes on.
| 1. LED component is not working properly.
2. Battery is dead.
| 1. Replace bulb.
2. Contact Customer Service.
3. Charge battery.
CARE AND MAINTENANCE
- Clean only with a dry, soft cloth. DO NOT use abrasive cleaners.
WARRANTY
The distributor warrants all of its lighting fixtures against defects in materials and workmanship for one (1) year from the date of purchase. If within this period the product is found to be defective, take a copy of the bill of sale as a proof of purchase and the product in its original carton to the place of purchase. The distributor will, at its option, repair, replace or refund the purchase price to the consumer. All costs of installation and removal of the fixture is the responsibility of the consumer. This warranty does not cover fixtures becoming defective due to misuse, accidental damage or improper handling and/or installation and specifically excludes liability for direct, incidental or consequential damages. As some states do not allow exclusions of limitations on an implied warranty, the above exclusion and limitation may not apply. This warranty gives you specific rights and you may also have other rights which may vary from state to state.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product. Failure to do so could lead to electrical shock, fire or other injuries that could be fatal.
WARNING
- To reduce the risk of damage to the fixture, DO NOT use power tools to assemble any part of the fixture.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
- Estimated Assembly Time: 15 minutes
TOOLS REQUIRED (NOT INCLUDED)
FEELING CONFIDENT? START YOUR NEXT PROJECT
- Visit Lowes.com for more information.
SAFETY INFORMATION
WARNING
- DO NOT repair, disassemble or modify the product.
- Do NOT tamper with or attempt to repair LED component of fixture. The light source is designed for this specific application and should not be serviced by untrained personnel. If any servicing is required, call our customer service department.
CAUTION
- TURN OFF ELECTRICITY at the circuit breaker box before beginning installation by switching the circuit breaker off.
- “DO NOT DISPOSE OF BATTERIES IN FIRE, BATTERIES MAY EXPLODE OR LEAK.” – When disposing of household alkaline batteries, it is best to check with your local and state recycling or household hazardous waste coordinators concerning the specifics of the program in your area. You may also locate a recycling center by calling 800-8-BATTERY or 877-2-RECYCLE or visit www.epa.gov/epawaste/index.htm or www.earth911.org for more information.
- Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
NOTE: The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, (2) this device must accept any interference received, including interference that may cause undesired operation use.
- Total wattage for this fixture is 5 watts; do NOT tamper with or attempt to repair the LED component of the fixture.
PACKAGE CONTENTS
HARDWARE CONTENTS
- Note: Hardware shown actual size.
INSTALLATION OVERVIEW
- Turn off the power source
- Turn (B) to the left (counterclockwise) to remove from (A).
- Drill pilot hole for (BB). Tap (BB) into pilot hole and then screw (CC) into (BB).
- Install six batteries (not included). Observe the diagram inside the battery compartment to install batteries correctly according to polarity. Instale seis baterías AA (no se incluyen).
- Batteries are to be inserted with the correct polarity.
- Choking/Ingestion Hazard – Small parts. Keep batteries away from children.
- DO NOT mix old and new batteries; DO NOT mix alkaline, standard (carbon-zinc) or rechargeable (nickel – cadmium) batteries or equivalent.
- Remove battery/batteries with low or no charge and dispose of them properly.
Switch on front of (A) has 3 settings:
- AUTO: The motion sensor is on.
- ON: Light is on.
- OFF: The light is off.
When motion is detected, the light turns on for 30 seconds. The motion sensor detects motion up to 9.84 feet away within a 120° angle.
- Align three tabs on (A) with three grooves on (B) and twist (A) clockwise until it stops.
PROJECT SOURCE and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>