REALPOWER PB-20K SE Power Bank User Manual

: June 2, 2024
: REALPOWER

Table of Contents

Manual
PB-20k SE

Manual

PB-20k SE

20.000 mAh

Thank you for choosing RealPower!

Quickly and easily recharge your mobile devices anytime, anywhere with the RealPower PB-20k SE Powerbank. The status of the charging process can be read from an LED display.

Loading the Powerbank:

A short press on the power on / off switch will indicate the remaining power bank charge from the LEDs.

1 LED lit = 0 % – 25 %
2 LEDs lit = 26 % – 50 %
3 LEDs light up = 51 % – 75 %
4 LEDs light up = 76 % – 100 %

To charge the power banks, simply connect the supplied charging cable with the power bank (IN / OUT) and via an AC adapter with a socket. The powerbank will now automatically charge themselves completely.

The integrated over-charge protection stops charging as soon as the battery is fully charged. The adapters and cables used for loading and unloading the power bank must comply with LPS and EN 60950-1: 2006 / A2: 2013. The charging current should be at least 5V / 2.100 mA.

Loading devices:

To charge your smartphone or other mobile device simply connect the charging cable of your device to one of the charging ports (OUT or IN / OUT).

Please note that the USB Type-C port can be used for loading and unloading.

Technical specifications:

Capacity: 20.000 mAh (74 Wh)
– In: USB Type-C DC 5 V / 2.000 mA max.
– Out USB 2x: DC 5 V / 2.100 mA max.
– USB Type-C DC 5 V / 2.100 mA max. 2.100 mA (total output)

20.000 mAh Lithium Polymer Battery
LED Indicator
USB Output
USB Type-C In- Output

Safety instructions:

– This Powerbank has been equipped with a lithium-polymer battery, which attains its full capacity only after several complete charging and discharging.
– Do not perform charging and discharging of the Powerbank at the same time.
– Only use suitable power packs (observe the indications about tension and charging current).
– Protect the Powerbank against collapse/fall — do not use any more after a collapse/fall.
– Please note that rechargeable batteries have only a limited number of charging cycles in spite of highly advanced technologies and need to be replaced or disposed of after some time.
– Do not open the housing — in case of defects, please contact the support or the specialist dealer.
– Charge the Powerbank every 3 months if it is not used, in order to maintain its full capability.
– Do not use the device in extremely cold, hot, humid or dusty environments. Do not expose the Powerbank to any direct sun radiation. Protect the product against open fire. There is a risk of explosion!
– Do not bridge any contacts — Risk of short circuit!
– Do not touch leaking batteries — Risk of injury through burns!
– Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to tie instructions.
– Do not dismantle, open or shred the battery.
– Do not expose the battery to heat or fire.
– Avoid storage in direct sunlight.
– Do not short-circuit the battery.
– Keep the battery out of the reach of children.
– Keep the battery clean and dry.
– Do not leave a battery on prolonged charge when not in use.
– Do not subject the battery to mechanical shock.

Intended use
This Powerbank is designed only for the power supply of devices with an operating voltage of 5-1211 DC (mobile phones, MP3 players, etc.). Any other uses or any use beyond the above described purpose would not be regarded as the intended use and may result in damages and injuries. Claims in any kind due to damages resulting of any use other than for the intended purposes have been excluded.

PB-20k SE

Powerbank mit 20.000 mAh

Find us on

wwwfacebook.com/ultron.de

Warranty Statement

ultron AG as manufacturer grants a 12 months limited warranty to the customer. All registered trademarks are the property of their respective owners. Specifications are subject to change without notice. Actual application windows might vary.
© ultron AG

August-Schmidt-Str.7
D-52477 Alsdorf
www.realpower.de