PROJECT SOURCE 26980 2 inch Cordless Blind Installation Guide

June 1, 2024
PROJECT SOURCE

PROJECT SOURCE 26980 2 inch Cordless Blind

PROJECT-SOURCE-26980-2-inch-Cordless-Blind-product

Product Information

Specifications

  • Product Name: 2 INCH CORDLESS BLIND
  • Models: 26980 – 27001, 94665 – 94686

FAQ

  • Q: What should I do if a part is missing or damaged?
    • A: Do not attempt to assemble, install, or operate the product. Contact customer service for assistance.
  • Q: How do I determine if I need inside or outside mounting?
    • A: Inside mounting is done within the window frame, while outside mounting is done on the wall above the window. Choose based on your preference and window type.

PACKAGE CONTENTS

PROJECT-SOURCE-26980-2-inch-Cordless-Blind-fig-1

HARDWARE CONTENTS

PROJECT-SOURCE-26980-2-inch-Cordless-Blind-fig-2

PREPARATION

Before beginning installation of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Estimated Assembly Time: 30 minutes. Tools Required for Assembly (not included): Pencil, drill, 1/16 in. bit, safety goggles, Phillips screwdriver, tape measure, level. Helpful Tools (not included): Step stool.

ASSEMBLY INSTRUCTIONS

  • 1a. For outside mounting, clip the mounting (AA) onto the headrail of blind (A). Hold blind (A) level at the height desired and center it over the window opening. Mark the exact location of each mounting bracket (AA) with a pencil. Remove the mounting brackets (AA) from the headrail of blind (A). Predrill the screw holes and then securing bracket (AA) to the wall or window molding with large screws (BB).
    • 1b. For inside mounting, clip the mounting brackets (AA) onto the headrail of blind (A). Hold blind (A) in place and make pencil mark at the rear of each mounting bracket (AA). Remove the mounting brackets (AA) from the headrail. Predrill the screw holes and then secure the mounting bracket (AA) to the wall or window molding with large screws (BB).
  • 2. Lift the headrail of blind (A) into position such that the inner front edge of the headrail slides into the slot at the front of each mounting bracket (AA).Push the headrail upward until the flexible tab at the bottom of each mounting bracket (AA) snaps onto the back of the headrail. Check carefully to assure each mounting bracket (AA) is properly snapped into place.PROJECT-SOURCE-26980-2-inch-Cordless-Blind-fig-7
  • 3. Install wand (B) by GRIPPING AND PULLING the wand tilter, located on the left hand side of blind (A) headrail, and hook wand (B) into the wand tilter.PROJECT-SOURCE-26980-2-inch-Cordless-Blind-fig-8
  • OPTIONAL: To install hold down brackets (DD), lower blind (A) to desired position. Screw hold down brackets (DD) into wall or window sill using medium screws (CC) and attach blind (A) to the hole in the cap on bottom rail.

OPTIONAL: ADJUST LENGTH OF BLIND

CAUTION: REMOVAL OF MORE THAN 5 SLATS WILL VOID THE WARRANTY
CAUTION : DO NOT CUT THE VERTICAL LADDER STRINGS, AS THIS WILL VOID THE WARRANTY.

  1. Lower blind (A) to maximum length. Cut the desired number of the bottom most slats, leaving the bottom rail as is. Blind (A) is able to shorten MAX 5 slats (up to 10”) with no operation concerns.
  2. Remove the cut slats.PROJECT-SOURCE-26980-2-inch-Cordless-Blind-fig-11
  3. Cut the excess horizontal ladder strings.
    • CAUTION: Do not cut the vertical ladder strings, as this will void the warranty.
  4. Remove the plugs from the bottom rail with a flathead screw driver (not included).
  5. Slide the bottom rail up to the horizontal ladder string you didn’t cut in step 3.
  6. Twist the cords back into the bottom rail and replace plugs.

OPERATING INSTRUCTIONS

PROJECT-SOURCE-26980-2-inch-Cordless-Blind-fig-14

  1. Raise or lower the blind (A) by gripping the bottom rail and lifting or lowering the bottom rail to the desired height.
  2. Open or close the blind (A) slats by turning the wand (C) until the slats are opened or closed to the desired amount.

CARE AND MAINTENANCE

  • Clean using damp cloth or vacuum using proper attachments or duster.

WARRANTY

For a period of one (1) year from the date of purchase, the manufacturer will replace this window covering with one of equal value if this window covering is found to be defective in material or workmanship. This warranty does not cover damage or defects caused by or resulting from improper maintenance, negligent or improper use, abuse, neglect, accidents, act of God, alteration, commercial use, installation, removal or reinstallation. This warranty is restricted to normal consumer use within the United States and Canada. To obtain warranty service, contact our customer service department at 866-389-8827.

REPLACEMENT PARTS

  • For replacement parts, call customer service 866-389-8827, 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at ascs@lowes.com.

PART / DESCRIPTION

  • 79074-3CZ0WTHW2LA
    • Hardware pack
    • (Contents AA x2, BB x4, CC x4, DD x2)

Contact

Questions, problems, missing parts?

Before returning to your retailer, call our customer service department at 866-389-8827, 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at ascs@lowes.com.

MODEL: 26980 – 27001, 94665 – 94686

ATTACH YOUR RECEIPT HERE

  • Item Number…………
  • Purchase Date…………

PROJECT SOURCE and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

PROJECT SOURCE User Manuals

Related Manuals