CLAYPAKY CL3002 Volero Batten Aqua Instruction Manual

CLAYPAKY CL3002 Volero Batten Aqua

Product Information

Specifications

• Product Name: VOLERO BATTEN AQUA CL3002
• Manufacturer: Claypaky
• PowerSupply: 100-240V, 3.3-8A
• Control Signal Compatibility: DMX / Art-Net

Product Usage Instructions

1. Safety Information
   It is important to carefully read and keep the safety information provided with the product. This information is also available digitally on the manufacturer’s website.

2. Unpacking and Preparation
   Ensure all packing contents are present as shown in Fig. 1. Prepare the fixture for installation.

3. Installation and Start-Up

4. Fixture Overview
   Review the components of the fixture including the anti-moisture valve, power connections, control signal inputs, functional buttons, and display.

5. Installing the Fixture
   Install the projector on the floor, truss, ceiling, or wall following safety guidelines. Use safety chains when required for support.

6. Connecting to Mains Supply
   Connect the power cord to the mains supply ensuring proper voltage and current requirements are met.

7. Connecting the Control Signal Line: DMX / Art-Net
   Connect the control signal line using DMX or Art-Net compatibility as needed for operation.

8. Switching on the Fixture and Basic Setup
   Power on the fixture and follow the instructions on the display for basic setup including setting the DMX address.

FAQ (Frequently Asked Questions)

• Q: Where can I find the safety information for the VOLERO BATTEN AQUA CL3002?
  A: The safety information can be found on the manufacturer’s website or in the digital format provided with the product.

• Q: How should I install the projector for optimal performance?
  A: The projector can be installed on various surfaces such as the floor, truss, ceiling, or wall. Ensure to use safety chains for support when necessary.

INSTRUCTION MANUAL

• Congratulations on choosing a Claypaky product!
• We thank you for your custom.
• Please note that this product, as all the others in the rich Claypaky range, has been designed and made with total quality to ensure excellent performance and best meet your expectations and requirements.

SAFETY INFORMATION

• IMPORTANT: Claypaky recommends you carefully read and keep the safety information on this product, also available in digital format at the following link:
• www.claypaky.com
• Ref: FIS02F – Safety Information Volero Batten Aqua

UNPACKING AND PREPARATION

Packing contents – Fig. 1

INSTALLATION AND START-UP

1. Fixture overview

2. Installing the fixture

   • Projector installation – Fig. 3

   • The projector can be installed on the floor resting on specific rubber feet, on a truss, on the ceiling or wall.

   • WARNING: the safety chains must be installed except when the projector rests on the floor. (Code 2x 105041/801 available upon request). This must be secured to the projector support structure and then hooked to the two fastening points.
     

   • Floor Line array connection – Fig. 4

3. Connecting to mains supply
   Connecting and disconnecting the power cord – Fig. 5
   Connections to the power mains – Fig. 6

4. Connecting the control signal line: DMX / Art-Net

   • Connections to the control signal line (DMX) – Fig. 7
   • Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ω characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. End connections must be made using XLR type 5-pin male/female connectors. A terminating plug must be inserted on the last projector with a resistance of 120 (minimum 1/4 W) between terminals 2 and 3. IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing must be connected to the shield braid and pin 1 of the connectors.

5. Switching on the fixture and basic SetUp

   • Switching on the projector – Fig. 8

   • Switch-on the fixture. The projector starts resetting the effects. At the same time, the following information scrolls on the display:

   • On conclusion of resetting in case of absence of the dmx signal, Tilt move to the “Home” position (Tilt 128 bit). The control panel (Fig. 7) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions: rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address.

   • During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status. It should be noted than  when this condition occurs, any possible value that has been modified but not yet confirmed with the F key will be cancelled.

   • Reversal of the display – Fig. 9

   • To activate this function, press UP B and DOWN C keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
     Setting the projector starting address

   • On each projector, the starting address must be set for the control signal (addresses from 1 to 512).

   • The address can also be set with the projector switched off.

Functions of the buttons – Using the menu

USING THE MENU:

1. Press LEFT D once – “Main Menu” appears on the display.
2. Use the UP and DOWN keys to select the menu to be used:
   • Setup (Setup Menu) : To set the setting options.
   • Option (Option Menu): To set the operating options
   • Informations (Information’s Menu): To read the counters, software version and other information.
   • Manual Control (Manual control Menu): To trigger the test and manual control functions.
   • Test (Test Menu): To check the proper functioning of effects
   • Advanced (Advanced Menu) : Access to the “Advanced menu” is recommended for a trained technical personnel.
3. Press to display the first item in the selected menu.
4. Use the UP and DOWN keys to select the MENU items.

Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply. All that is needed is to press RIGHT to momentarily activate the display and thus access the settings. Once the required operations have been carried out, the display will switch off again after a wait time of 30 seconds.

MAINTENANCE

1. Fuses replacing

   • Fuse replacing – Fig. 10
     Each Volero Batten Aqua has 1 fuse 10AT 250V, associated with the main power cord connection.

2. Periodical cleaning & Caution

   • Light collimation system
     This product contains internal light collimation system. Avoid intense light from any angle.

   • Parts requiring frequent cleaning.

WARNING

• IP66 fixture
• Failure to completely remove power from fixture prior to servicing can lead to serious injury or death. For additional service information please contact service@claypaky.it

IMPORTANT

• The screws to be removed have rubber sleeve gaskets at the threaded end of the screw. DO NOT LOOSE these. They must be reinstalled when reassembly is done. If these rubber sleeve gaskets are damaged, they must be replaced with exact original equipment (OE) parts, we also suggest to replace the rubber sleeve gasket every 2 years.
• To maintain IP66 rating each cover has rubber gasket on it. If any rubber gasket is lost or damaged, it must be replaced by an original equipment
  (OE) part. We also suggest to replace the rubber sleeve gasket every 2 years.

CAUTION :

• To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.).
  It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:

  • General cleaning of internal parts.
  • Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky.
  • General visual check of the internal components, cabling, mechanical parts, etc.
  • Electrical, photometric and functional checks; eventual repairs.

Cleaning the lenses
Only use neutral soap and water to clean the lenses, then dry it carefully with a soft, non-abrasive cloth.
(WARNING: the use of alcohol or any other detergent could damage the lenses).

Battery removal

This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.

DIMENSIONS

CAUSE AND SOLUTION OF PROBLEMS

VOLERO BATTEN AQUA

• www.claypaky.com
• Service support & Helpdesk: https://e-assist.tech
• IST02R – EN – Rev.A 05/2023

References

• Claypaky | Professional Lighting
• Claypaky - home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>