CLAYPAKY CL3000 Axcor Wash 600 Moving Head Light Fixture Instruction Manual
- June 1, 2024
- CLAYPAKY
Table of Contents
CLAYPAKY CL3000 Axcor Wash 600 Moving Head Light Fixture
Product Information
Specifications
- Product Name: AXCOR WASH 600 / AXCOR WASH 600 HC
- Model Number: CL3000 / CL3001
- Manufacturer: Claypaky
- Control Signal: DMX / Art-Net
- Power Supply: Mains
FAQ
- Q: Where can I find additional safety information for the AXCOR WASH 600 series?
- A: Additional safety information can be found in digital format at www.claypaky.com using the reference [FIS00W – Safety Information Axcor 600 series].
Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Claypaky range,
has been designed and made with total quality to ensure excellent performance
and best meet your expectations and requirements.
UNPACKING AND PREPARATION
PAN Mechanism Lock and Release (every 90°) – Fig. 2
TILT Mechanism Lock and Release (every 45°) – Fig. 3
INSTALLATION AND START-UP
Installing the fixture
- The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.
- WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/001 available on request).
- This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.
Connecting to manis supply
Connecting the control signal line: DMX / Art-Net
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5 pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT
- The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.
Switching on the fixture and basic SetUp
Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:
On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 128 bit – Tilt 128 bit). The control panel (Fig. 8) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions: rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set). During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status. It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the OK key will be cancelled.
- Reversal of the display – Fig. 9
- To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
- Setting the projector starting address
- On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
- The address can also be set with the projector switched off.
- Setting the projector Fixture ID
- On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255).
- The Fixture ID address can be set with the projector switched off.
Functions of the buttons – Using the menu
USING THE MENU:
- Press OK once – “Main Menu” appears on the display.
- Use the UP and DOWN keys to select the menu to be used:
- Setup (Setup Menu): To set the setting options.
- Option (Option Menu): To set the operating options
- Informations (Informations Menu): To read the counters, software version and other information.
- Manual Control (Manual control Menu): To trigger the test and manual control functions.
- Test (Test Menu): To check the proper functionning of effects
- Advanced (Advanced Menu): Access to the “Advanced menu” is recommended for a trained technical personnel.
- Press OK to display the first item in the selected menu.
- Use the UP and DOWN keys to select the MENU items.
Setting addresses and options with the projector disconnected
- The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply.
- All that is needed is to press OK to momentarily activate the display and thus access the settings. Once the required operations have been carried out, the display will switch off again after a wait time of 30 seconds.
MAINTENANCE
Opening the covers
Periodical cleaning
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.).
Use a soft cloth dampened with any detergent liquid for cleaning glass to remove the dirt from the reflectors, from the lenses and filters. It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:
- General cleaning of internal parts.
- Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky.
- General visual check of the internal components, cabling, mechanical parts, etc.
- Electrical, photometric and functional checks; eventual repairs.
Effects module removal
NOTE:
- Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards.
- Do not switch-on the fixtures with wiring harness disconnected.
- Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards.
- Do not switch-on the fixtures with wiring harness disconnected.
- IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged.
- Insertion of the effect modules: Repeat the operations indicated in Fig. 15, 16, 17 and 18 in reverse order.
- IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged.
- Insertion of the effect modules: Repeat the operations indicated in Fig. 15, 16, 17 and 18 in reverse order.
- IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged.
- Insertion of the effect modules: Repeat the operations indicated in Fig. 15, 16, 17 and 18 in reverse order.
Cleaning of the filters
Battery removal
Disposal
- This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.
Frost filter removal
Accessories
DIMENSIONS
- www.claypaky.com
- Service support & Helpdesk: https://e-assist.tech
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>