CLAYPAKY CL2017 Mini-B Par LED Aqua Instruction Manual
- June 1, 2024
- CLAYPAKY
Table of Contents
Mini-B ParLED Aqua
Mini-B ParLED Aqua WW
CL2018
CL2017
INSTRUCTION MANUAL
CL2017 Mini-B Par LED Aqua
Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Claypaky range,
has been designed and made with total quality to ensure excellent performance
and best meet your expectations and requirements.
SAFETY INFORMATION
SAFETY INFORMATION
IMPORTANT: Claypaky recommends you carefully read and keep the safety
information on this product, also available in digital format at the following
link: www.claypaky.com
Ref: [FIS020 – Safety information Mini-B ParLED Aqua]
UNPACKING AND PREPARATION
INSTALLATION AND START-UP
3.1 Installing the fixture
The projector can be installed on the floor on a truss or on the ceiling or
wall.
WARNING: with the exception of when the projector is positioned on the
floor, the safety cable must be fitted. (Cod. 105041/001 available on
request).
This must be securely fixed to the support structure of the projector and then
connected to the fixing point.
3.2 Connecting to manis supply
3.3 Connecting the control signal line: DMX / Art-Net
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded,
120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those
specified. The end connections must be made using XLR type 5-pin male/female
connectors. A terminating plug must be inserted into the last projector with a
resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the
metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors. IP66 line is recommended.
3.4 Switching on the fixture and basic SetUp
Plug-in the power connector. The projector starts the reset procedure. At the same time, the following information scrolls on the display:
The control panel (Fig. 7) has a display and buttons for the complete
programming and management of the projector menu. The display can be in one of
two conditions: standby or setting status. When it is in standby, the display
shows the projector’s DMX address.
During the setting status, after a wait time (about 30 seconds) without any
key having been pressed, the display automatically returns in standby. It
should be noted than when this condition occurs, any possible value that has
been modified but not yet confirmed with the ENTER key will be cancelled.
To activate this function, press UP and DOWN keys simultaneously while the
display is in standby. This status will be memorised and maintained even for
the next time it will be switched on. To return to the initial state, repeat
the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal
(valid addresses from 1 to 501).
The address can also be set with the projector switched off.
Functions of the buttons – Using the menu
| Return to the top level
---|---
| Confirms the displayed value, or activates the displayed function, or enters
the successive menu.
| Increases the value displayed (with auto-repetitions) or passes to the
previous item in a menu.
| Decreases the value displayed (with auto-repetitions) or passes to the next
item in the menu.
IMPORTANT: To Unlock the display press the buttons sequence UP – DOWN –
UP – DOWN – ENTER.
USING THE MENU:
-
Press MENU once – “Main Menu” appears on the display. Menu Up
-
Use the UP and DOWN keys to select the menu to be used:
• Setup: To set the setting options.
• Option: To set the operating options
• Information: To read the counters, software version and other information.
• Manual Control: To trigger the test and manual control functions.
• Test: To check the proper functioning of effects
• Advanced: Access to the “Advanced menu” is recommended for a trained technical personnel. -
Press Enter to display the first item in the selected menu.
-
Use the UP Down and DOWN keys to select the MENU items.
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can
also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press RIGHT to momentarily activate the display and
thus access the settings. Once the required operations have been carried out,
the display will switch off again after a wait time of 30 seconds.
MAINTENANCE
4.1 Maintenance and Caution
WARNING
– IP 66 fixture
– Failure to completely remove power from fixture prior to servicing can lead
to serious injury or death.
For additonal service information please contact service@claypaky.it
IMPORTANT
The screws to be removed have rubber sleeve gaskets at the threaded end of the
screw. DO NOT LOOSE these. They must be reinstalled when reassembly is done.
If these rubber sleeve gaskets are damaged, they must be replaced with exact
original equipment (OE) parts, we also suggest to replace the rubber sleeve
gasket every 2 years.
To mantain IP66 rating each covers have rubber gasket on it, If any rubber
gasket is lost or damaged, they must be replaced by an original equipment (OE)
parts, we also suggest to replace the rubber sleeve gasket every 2 years.
CAUTION:
-
It is recommended not to use compressed air with more than 4 atmospheres for cleaning the internal parts of the fixture, led board area.
This is to avoid damaging electronic components. -
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.).
It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:
– General cleaning of internal parts.
– Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky.
– General visual check of the internal components, cabling, mechanical parts, etc.
– Electrical, photometric and functional checks; eventual repairs.
Cleaning the lenses
Only use neutral soap and water to clean the lenses, then dry it carefully
with a soft, non-abrasive cloth. (WARNING: the use of alcohol or any other
detergent could damage the lenses).
4.2 Battery removal
Battery removal – Fig. 10
This product contains a rechargeable battery. To preserve the environment,
please dispose the battery at the end of its life according to the regulation
in force.
4.3 Opening the covers
DIMENSIONS
CAUSE AND SOLUTION OF PROBLEMS
www.claypaky.com
Service support & Helpdesk:
https://e-assist.tech
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>