CLAYPAKY C61515 Scenius Unique Lamp Hybrid Moving Light Instruction Manual

CLAYPAKY C61515 Scenius Unique Lamp Hybrid Moving Light

Product Information

Specifications

• Product Name: SCENIUS UNICO
• Model Number: C61515
• Manufacturer: Claypaky

Product Usage Instructions

Safety Information
Before using the product, carefully read and follow all safety instructions provided in the manual or digital format at www.claypaky.com.

Unpacking and Preparation
When unpacking the product, ensure all contents are present as shown in Fig. 1. Follow the instructions for unlocking and preparing the fixture for installation.

Installation and Start-Up
Install the projector on the floor using rubber feet or on a truss/ceiling/wall with the appropriate safety measures. Connect the power cable as shown in Fig. 5. Remember to use the safety cable when not on the floor.

Control Panel
Connect the projector to the mains supply following the guidelines in Fig. 6. Use the control panel to set up the fixture ID, DMX address, and manage warning messages. To switch on the projector, press the designated switch.

Maintenance
Refer to the maintenance section of the manual for guidelines on cleaning and servicing the SCENIUS UNICO to ensure optimal performance.

FAQ

1. Q: Where can I find additional safety information?
   A: Additional safety information can be found in digital format at www.claypaky.com or refer to the safety section in the user manual.

2. Q: How do I reset the effects on the projector?
   A: To reset the effects, press the switch to turn on the projector. The effects will begin resetting automatically.

Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Claypaky range, has been designed and made with total quality to ensure excellent performance and best meet your expectations and requirements.

SAFETY INFORMATION
SAFETY INSTRUCTIONS
IMPORTANT: Claypaky recommends you carefully read and keep the safety information on this product, also available in digital format at the following link: www.claypaky.com
Ref: [FIS00L – Safety Information Scenius]

UNPACKING AND PREPARATION

Packing contents – Fig. 1

PAN Mechanism Lock and Release (every 90°) – Fig. 2
TILT Mechanism Lock and Release (every 45°) – Fig. 3

INSTALLATION AND START-UP

Installing the projector – Fig. 4
The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.
WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/001 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.

Connecting and disconnecting power cable – Fig. 5

CONTROL PANEL

Connecting to the mains supply – Fig. 6

Connecting to the control signal line (DMX) – Fig. 7
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.

Switching on the projector – Fig. 8
Press the switch. The projector starts resetting the effects.

At the same time, the following information scrolls on the display:

On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 128 bit – Tilt 128 bit). The control panel (Fig. 8) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions: rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set). During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status. It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the key will be cancelled.

Reversal of the display – Fig. 9
To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.

Setting the projector starting address
On each projector, the starting address must be set for the control signal (addresses from 1 to 512).  The address can also be set with the projector switched off.

Setting the projector Fixture ID
On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255). The Fixture ID address can be set with the projector switched off.

Functions of the buttons – Using the menu

USING THE MENU:

1. Press once – “Main Menu” appears on the display.
2. Use the UP and DOWN keys to select the menu to be used:
   • Setup (Setup Menu): To set the setting options.
   • Option (Option Menu): To set the operating options
   • Informations (Informations Menu): To read the counters, software version and other information.
   • Manual Control (Manual control Menu): To trigger the test and manual control functions.
   • Test (Test Menu): To check the proper functionning of effects
   • Advanced (Advanced Menu): Access to the “Advanced menu” is recommended for a trained technical personnel.
3. Press to display the first item in the selected menu.
4. Use the UP and DOWN keys to select the MENU items.

Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply. All that is needed is to press F to momentarily activate the display and thus access the settings. Once the required operations have been carried out, the display will switch off again after a wait time of 30 seconds.

MAINTENANCE

Locking and releasing Pan and Tilt movements – Refer to the instructions in the UNPACKING AND PREPARATION section.
Opening the head covers – Fig. 10.
Closing the head covers – Fig. 11.

Periodical cleaning – Fig. 12
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.). Use a soft cloth dampened with any detergent liquid for cleaning glass to remove the dirt from the reflectors, from the lenses and filters. It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:

• General cleaning of internal parts.
• Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky.
• General visual check of the internal components, cabling, mechanical parts, etc.
• Electrical, photometric and functional checks; eventual repairs.

NOTE: keep a careful cleaning of the ”CMY/colour filters assembly” to prevent rapid deterioration.

Cleaning of the filters – Fig. 13.

Extraction of the effect modules: Preliminary operations – Fig. 14.

Extraction of the effect modules: Preliminary operations – Fig. 15.

Extraction of the effect modules – Fig. 16.
IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 14, 15, 16, 17 and 18 in reverse order.

Extraction of the effect modules – Fig. 17.
IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 14, 15, 16, 17 and 18 in reverse order.

Extraction of the effect modules – Fig. 18.
IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 14, 15, 16, 17 and 18 in reverse order.

Opening and closing lamp compartment – Fig. 19

Lamp change – Fig 20
Take the new lamp out of its package and insert in the fitting. WARNING: do not touch the lamp’s envelope with bare hands. Should this happen, clean the bulb with a cloth soaked in alcohol and dry it with a clean, dry cloth.
CAUTION: Fast lamp ON-OFF cycles (for example 10 minutes ON / 10 minutes OFF) will reduce the lamp life.
ATT200/001 is the part number of a CP tool, that could help you to take off the lamp from the fixture.

Lamp regulation – Fig. 21
To centre the lamp, turn the three adjusting screws as shown in the figure.

Bearing group replacement – Fig. 22

Replacing rotating gobos (ø 32.8 mm – max 23 mm image – thickness 1.1 mm) – Fig. 23

• Before use custom gobos contact Claypaky;
• The original gobos have a special coating designed specifically to resist to the high temperatures;
• The rotating gobo wheel only use dichroic glass gobos (it is not possible to use metal gobos);
• For more information contact Claypaky;

Gobo orientation – Fig. 24
The pictures shown the correct gobos orientation.

Battery removal – Fig. 25
This product contains a rechargeable lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.

DIMENSIONS

www.claypaky.com – Service support & Helpdesk: https://e-assist.tech

References

• Claypaky | Professional Lighting
• Claypaky - home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>