CLAYPAKY CL3018 LED Sinfonya Profile Based Fixture Instruction Manual
- June 1, 2024
- CLAYPAKY
Table of Contents
SINFONYA PROFILE 600
SINFONYA PROFILE 600 EX
CL3018
INSTRUCTION MANUAL
Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Claypaky range,
has been designed and made with total quality to ensure excellent performance
and best meet your expectations and requirements.
SAFETY INFORMATION
IMPORTANT: Claypaky recommends you carefully read and keep the safety
information on this product, also available in digital format at the following
link: www.claypaky.com
Ref: FIS02A – Safety Information Sinfonya Profile 600 / EX
UNPACKING AND PREPARATION
Packing contents – Fig.
1
PAN Mechanism Lock and Release (every 90°) – Fig. 2
TILT Mechanism Lock and Release (every 45°) – Fig. 3
INSTALLATION AND START-UP
3.1 Installing the fixture
Installing the projector – Fig.
4
The projector can be installed on the floor resting on special rubber feet, on
a truss or on the ceiling or wall.
WARNING: with the exception of when the projector is positioned on the
floor, the safety cable must be fitted. (Cod. 105041/003 available on
request).
This must be securely fixed to the support structure of the projector and then
connected to the fixing point at the centre of the base.
3.2 Connecting to manis supply
3.3 Connecting the control signal line: DMX / Art-Net
Connecting to the control signal line (DMX) – Fig. 8
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded,
120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those
specified. The end connections must be made using XLR type 5 pin male/female
connectors. A terminating plug must be inserted into the last projector with a
resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the
metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors.
3.4 Switching on the fixture and basic SetUp
Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:
On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt
move to the “Home” position (Pan 128 bit – Tilt 128 bit). The control panel
(Fig. 8) has a display and buttons for the complete programming and management
of the projector menu. The display can be in one of two conditions:
rest status and setting status. When it is in the rest status, the display
shows the projector’s DMX address and the Fixture ID address (if set). During
menu setting status, after a wait time (about 30 seconds) without any key
having been pressed, the display automatically returns to rest status. It
should be noted than when this condition occurs, any possible value that has
been modified but not yet confirmed with the F key will be cancelled.
Reversal of the display – Fig. 10
To activate this function, press UP and DOWN keys simultaneously while the
display is in the rest mode. This status will be memorised and maintained even
for the next time it will be switched on. To return to the initial state,
repeat the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal
(addresses from 1 to 512).
The address can also be set with the projector switched off.
Setting the projector Fixture ID
On each projector, the Fixture ID address must be set for an easy
identification of the fixtures in an installation (ID from 1 to 255).
The Fixture ID address can be set with the projector switched off.
Functions of the buttons – Using the menu
| Confirms the displayed value, or activates the displayed function, or
enters the successive menu.
---|---
DOWN Decreases the value displayed (with auto-repetitions) or passes to the
next item in the menu.
UP Increases the value displayed (with auto-repetitions) or passes to the
previous item in a menu.
Return to the top level
Commute from units, tens, hundreds, in the “Address”, “Fixture ID” and
“Calibration” menù.
USING THE MENU:
-
Press once – “Main Menu” appears on the display.
-
Use the UP and DOWN keys to select the menu to be used:
• Setup (Setup Menu): To set the setting options.
• Option (Option Menu): To set the operating options
• Informations (Informations Menu): To read the counters, software version and other information.
• Manual Control (Manual control Menu): To trigger the test and manual control functions.
• Test (Test Menu): To check the proper functionning of effects
• Advanced (Advanced Menu): Access to the “Advanced menu” is recommended for a trained technical personnel. -
Press F to display the first item in the selected menu.
-
Use the UP and DOWN keys to select the MENU items.
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can
also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press to momentarily activate the display and thus
access the settings. Once the required operations have been carried out, the
display will switch off again after a wait time of 30 seconds.
MAINTENANCE
4.1 Opening the covers
Locking and releasing Pan and Tilt movements – Refer to the instructions in
the UNPACKING AND PREPARATION section.
Opening the head covers – Fig. 11.
Closing the head covers – Fig. 12.
4.2 Periodical cleaning
Periodical cleaning – Fig. 13
To ensure optimal operation and performance for a long time it is essential to
periodically clean the parts subject to dust and grease deposits. The
frequency with which the following operations are to be carried out depends on
various factors, such as the amount of the effects and the quality of the
working environment (air humidity, presence of dust, salinity, etc.).
Use a soft cloth dampened with any detergent liquid for cleaning glass to
remove the dirt from the reflectors, from the lenses and filters. It is
recommended that the projector undergoes an annual service by a qualified
technician for special maintenance involving at least the following
operations:
- General cleaning of internal parts.
- Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky.
- General visual check of the internal components, cabling, mechanical parts, etc.
- Electrical, photometric and functional checks; eventual repairs.
4.3 Effects module removal
Extraction of the effect modules: Preliminary operations – Fig. 14.
NOTE:
– Do not disconnect wiring harnesses when the fixtures is switched-on, to
avoid to damage electronic boards.
– Do not switch-on the fixtures with wiring harness disconnected.
NOTE:
– Do not disconnect wiring harnesses when the fixtures is switched-on, to
avoid to damage electronic boards.
– Do not switch-on the fixtures with wiring harness disconnected.
IMPORTANT: Grasp the modules using the support structure and not the
details which could get damaged.
Insertion of the effect modules: Repeat the operations indicated in Fig. 16,
17 and 18 in reverse order.
IMPORTANT: Grasp the modules using the support structure and not the
details which could get damaged.
Insertion of the effect modules: Repeat the operations indicated in Fig. 16,
17 and 18 in reverse order.
Extraction of the effect
modules – Fig. 18.
IMPORTANT: Grasp the modules using the support structure and not the
details which could get damaged.
Insertion of the effect modules: Repeat the operations indicated in Fig. 16,
17 and 18 in reverse order.
4.4 Cleaning of the filters
4.5 Rotating gobos
– The rotating gobo wheel only use dichroic glass gobos (it is not possible to
use metal gobos);
– For more information contact Claypaky;
The pictures shown the correct gobos orientation.
4.6 Battery removal
This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.
DIMENSIONS
CAUSE AND SOLUTION OF PROBLEMS
THE PROJECTOR WILL NOT SWITCH ON| ELECTRONICS NON-OPERATIONAL| DEFECTIVE
PROJECTION| REDUCED LUMINOSITY| POSSIBLE CAUSES| PROBLEMS
CHECKS AND REMEDIES
---|---|---|---|---|---
| | | | No mains supply.| Check the power supply voltage.
| | | | Light source exhausted or defective.| Call an authorised technician.
| | | | Signal transmission cable faulty or disconnected. Incorrect
addressing.| Replace the cables.
| | | | Fault in the electronic circuits.| Check addresses (see instructions).
| | | | Lenses broken| Call an authorised technician.
| | | | Dust or grease deposited.| Call an authorised technician.
| | | | | Clean (see instructions).
www.claypaky.com – Service support & Helpdesk: https://e-assist.tech
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>