CLAYPAKY CD3004 Sharpy X Spot Moving Head Fixture Instruction Manual
- June 1, 2024
- CLAYPAKY
Table of Contents
- CLAYPAKY CD3004 Sharpy X Spot Moving Head Fixture
- Product Information
- Product Usage Instructions
- Connecting to Main Supply
- FAQ
- SAFETY INFORMATION
- UNPACKING AND PREPARATION
- INSTALLATION AND START-UP
- MAINTENANCE
- DIMENSIONS
- CAUSE AND SOLUTION OF PROBLEMS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CLAYPAKY CD3004 Sharpy X Spot Moving Head Fixture
Product Information
Specifications
- Product Name: SHARPY X SPOT
- Model Number: CD3004
- Manufacturer: Claypaky
Product Usage Instructions
Safety Information
Before using the SHARPY X SPOT, carefully read and follow the safety information provided in the manual or online at www.claypaky.com.
Unpacking and Preparation
Ensure all packing contents are present as shown in Fig. 1 of the manual. Familiarize yourself with the locked and unlocked positions of the fixture as indicated.
Installation and Start-Up
Installing the Fixture
Install the projector on the floor, truss, ceiling, or wall using appropriate mounting methods. Remember to always use the safety cable when not placing the projector on the floor.
Connecting to Main Supply
Follow Fig. 6 for connecting and disconnecting the power cable. Connect the fixture to the mains supply as shown in Fig. 7.
Connecting the Control Signal Line: DMX / Art-Net
Connect the control signal line using DMX or Art-Net protocols as per the instructions provided.
Switching on the Fixture and Basic Setup
To switch on the projector, follow Fig. 9 instructions. The display will show essential information such as model, firmware version, date, hour, and DMX address. Note that any unconfirmed modifications will be canceled during this process.
Maintenance
- Opening the covers
- Periodical cleaning
- Effects module removal
- Rotating gobos
- Battery removal
Dimensions
Refer to the product manual for detailed dimensions of the SHARPY X SPOT.
Cause and Solution of Problems
If you encounter any issues with the SHARPY X SPOT, refer to the manual for troubleshooting steps or contact customer support for assistance.
FAQ
Q: Where can I find the safety information for the SHARPY X SPOT?
A: The safety information is available in the manual and can also be accessed online at www.claypaky.com.
Q: How do I reset the effects on the projector?
A: To reset the effects, switch on the fixture following the instructions provided in Fig. 9 of the manual.
Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Claypaky range,
has been designed and made with total quality to ensure excellent performance
and best meet your expectations and requirements.
SAFETY INFORMATION
IMPORTANT: Claypaky recommends you carefully read and keep the safety
information on this product, also available in digital format at the following
link: www.claypaky.com
Ref: FIS027 – Safety Information Sharpy X Spot
UNPACKING AND PREPARATION
INSTALLATION AND START-UP
Installing the fixture
The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.
WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.
Connecting to manis supply
Connecting the control signal line: DMX / Art-Net
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 5 pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.
Switching on the fixture and basic SetUp
Switch-on the fixture. The projector starts resetting the effects. At the same time, the following information scrolls on the display:
On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt
move to the “Home” position (Pan 128 bit – Tilt 128 bit). The control panel
(Fig. 8) has a display and buttons for the complete programming and management
of the projector menu. The display can be in one of two conditions: rest
status and setting status. When it is in the rest status, the display shows
the projector’s DMX address.
During menu setting status, after a wait time (about 30 seconds) without any
key having been pressed, the display automatically returns to rest status. It
should be noted than when this condition occurs, any possible value that has
been modified but not yet confirmed with the OK key will be cancelled.
To activate this function, press keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal
(addresses from 1 to 512).
The address can also be set with the projector switched off.
Functions of the buttons – Using the menu
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can
also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press RIGHT to momentarily activate the display and
thus access the settings. Once the required operations have been carried out,
the display will switch off again after a wait time of 30 seconds.
MAINTENANCE
Opening the covers
Locking and releasing Pan and Tilt movements – Refer to the instructions in
the UNPACKING AND PREPARATION section.
Opening the head covers – Fig. 11.
Closing the head covers – Fig. 12.
Periodical cleaning
Periodical cleaning – Fig. 13
To ensure optimal operation and performance for a long time it is essential to
periodically clean the parts subject to dust and grease deposits. The
frequency with which the following operations are to be carried out depends on
various factors, such as the amount of the effects and the quality of the
working environment (air humidity, presence of dust, salinity, etc.).
Use a soft cloth dampened with any detergent liquid for cleaning glass to
remove the dirt from the reflectors, from the lenses and filters. It is
recommended that the projector undergoes an annual service by a qualified
technician for special maintenance involving at least the following
operations:
- General cleaning of internal parts.
- Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky.
- General visual check of the internal components, cabling, mechanical parts, etc.
- Electrical, photometric and functional checks; eventual repairs.
Effects module removal
Extraction of the effect modules – Fig. 14.
IMPORTANT: Grasp the modules using the support structure and not the details
which could get damaged. Insertion of the effect modules: Repeat the
operations indicated in Fig. 14, 15 and 16 in reverse order.
Extraction of the effect modules – Fig. 15.
IMPORTANT: Grasp the modules using the support structure and not the details
which could get damaged. Insertion of the effect modules: Repeat the
operations indicated in Fig. 14, 15 and 16 in reverse order.
Take the new lamp out of its package and insert in the fitting.
WARNING: do not touch the lamp’s envelope with bare hands. Should this happen, clean the bulb with a cloth soaked in alcohol and dry it with a clean, dry cloth.
Lamp regulation
To centre the lamp, turn the adjusting screw as shown in the figure.
WARNING: The lamp must be adjusted with the projector switched off. After adjusting, close the effects covers, switch on the projector and check that the adjustment has been correctly made. If necessary, switch off the projector, remove the effects covers and repeat lamp adjustment.
REMARK:
- Lifetime of the lamp will be influenced by the switching cycle.
- After a successful starting, attempt to keep the lamp burning for at least 15 minutes in order to complete the chemical cycle of the lamp to secure the lifetime.
- After switching-off the lamp wait at least 2 minutes before switching-on it again.
Rotating gobos
Replacing rotating gobos (ø 19 mm – max 13.5 mm image – thickness 1.1 mm) – Fig. 19
- The rotating gobo wheel only use dichroic glass gobos (it is not possible to use metal gobos);
- For more information contact Claypaky;
The pictures shown the correct gobos orientation.
Battery removal
This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.
DIMENSIONS
CAUSE AND SOLUTION OF PROBLEMS
www.claypaky.com – Service support & Helpdesk: https://e-assist.tech
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>