Stadler Form R-017 Roger Air Purifier Instruction Manual

Stadler Form R-017 Roger Air Purifier Instruction Manual

Congratulations! You have just acquired the exceptional air purifier ROGER/ ROGER LITTLE / ROGER BIG. It will give you great pleasure and improve the indoor air for you.

As with all domestic electrical appliances, particular care is also needed with this model in order to avoid injury, fire damage or damage to the appliance. Please study these operating instructions carefully before using this appliance for the first time and follow the safety advice on the appliance itself.

Description of the appliance

The appliance consists of the following main components:

1. Textile pre-filter with integrated Sanitized® hygiene function
2. Dual Filter TM (HEPA, Activated Carbon)
3. Housing
4. Mains cable for power supply
5. Connection for mains cable
6. On/off button
7. Air quality indicator
8. Button for the selection of the speed level
9. Button for auto mode
10. Button for timer
11. Button for night mode (air quality indicator in normal mode or switched off)
12. Button for HEPA RESET (Dual Filter-timer und exchange reminder)
13. Button for WiFi (only Roger and Roger big)
14. Air inlet
15. Position of gas sensor (Roger little), gas and particle sensor (Roger / Roger big)
16. Fan
17. Air outlet
18. Carrying handle

Important Safety Instructions

Please read through the operating instructions carefully before you use the appliance for the first time and keep them safely for later reference; if necessary pass them on to the next owner.

• Stadler Form refuses all liability for loss or damage which arises as a result of failure to follow these operating instructions.
• The appliance is only to be used in the home for the purposes described in these instructions. Unauthorised use and technical modifications to the appliance can lead to danger to life and health.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Only connect the cable to alternating current. Observe the voltage information given on the appliance.
• Do not use damaged extension cords.
• Do not run the power cord over sharp edges and make sure that it does not get trapped.
• Do not pull the plug from the socket with wet hands or by holding on to the power cord.
• Do not use the appliance in immediate vicinity of a bath tub, a shower or a swimming pool (observe a minimum distance of 3m). Place the appliance such that a person in the bath tub cannot touch the appliance.
• Do not place the appliance near a heat source. Do not subject the power cord to direct heat (such as a heated hotplate, open flames, hot iron sole plates or heaters for example). Protect power cords from oil.
• See to it that the appliance is properly positioned to ensure a high stability during its operation and make sure that no one can trip over the power cord.
• The appliance is not splash-proof.
• For indoor use only.
• Do not store the appliance outdoors.
• Store the appliance in a dry place inaccessible to children (pack the appliance).
• If the power cord is damaged, it must be replaced by the manufacturer or a repair shop authorized by the manufacturer or by similarly qualified persons in order to avoid a hazard.
• Prior to any maintenance, cleaning and after each use, switch off the appliance and unplug the mains cable from the socket.

Filter description

Textile Pre-filter (1) The textile pre-filter (1) removes coarse dust particles and dirt from the air. By doing this, it protects the Dual FilterTM and prolongs its service life. The integrated Sanitized®* hygiene function protects the textile pre-filter against microbial growth. The textile pre- filter (1) must be cleaned regularly, once or twice a month depending on the level of soiling, using the textile brush attachment for your vacuum cleaner. In the case of heavy soiling, the textile pre-filter (1) can also be washed in a washing machine at 30° on a gentle cycle. The antimicrobial protection provided by Sanitized® is guaranteed for at least 20 washes. Allergy sufferers are recommended to wash the textile pre-filter once a month and all other users every 3 months. Let the textile pre-filter (1) dry completely before attaching it to the appliance again.
Sanitized® is the worldwide leading Swiss producer of the antimicrobial hygiene function and material protection for textiles and polymers.
Dual FilterTM: HEPA, Activated Carbon (2) The Dual FilterTM is the heart of the air purifier. It is a combination of HEPA filter and Activated Carbon filter.
The HEPA filter part of the Dual FilterTM filters pollutants out of the air, such as fine dust, pollen, viruses and bacteria.
The Activated Carbon filter absorbs gases present in the air (bad odors, tobacco smoke, formaldehyde, toluene, volatile organic compounds, etc.) and filters them out of the air. The capacity of the Dual FilterTM is limited, which means that it must be replaced every 8–12 months, depending on its exposure to air and gases. Should you notice before eight months has passed that bad odors are no longer being eliminated, this is an indication that the filter needs to be changed.

Setting up / operation

1. Remove the textile pre-filter (1) by taking hold of the top on both sides and pulling it forwards. Take the Dual FilterTM (2) from its housing (3) and remove the plastic film. Set the Dual FilterTM (2) in place so that the two textile tabs are visible on the front side. Arrows on the top of the filter (2) indicate the direction in which the filter must be inserted. Important: Roger big has a textile pre-filter on both sides and a Dual FilterTM, therefore both Dual FilterTMs must be unpacked and inserted.
2. Refit the textile pre-filter (1) by inserting the positioning aids near the bottom of the textile pre-filter (1) into the notches on the housing (3) and then tilting the textile pre-filter (1) towards the housing until it is locked into place at the top by the magnets on the housing (3). Make sure that the LED cylinder at the front towards the bottom of the appliance is inserted in the hole on the pre-filter.
3. Place Roger/Roger little / Roger big to the desired location on a flat surface, ideally centered in the room. This allows air to be supplied from all sides.
4. Connect the mains cable (4) to its connection (5) on the unit and then to a suitable power outlet.
5. Turn on Roger/Roger little/ Roger big by pressing the on/off button (7). The controls and the display light up in sequence from right to left. If no further buttons are pressed within 10 seconds, the display goes out again. Otherwise, visibility is extended by a further 10 seconds. Pressing the on/off button (6) or the controls lights them back up. To turn Roger/ Roger little / Roger big off, press the on/off button (6) for two seconds.
6. Air quality is measured by means of various sensors (Roger / Roger big = gas and particle sensor PM2.5 / Roger little = gas sensor) and is indicated by the air quality indicator (7) in front of the textile pre-filter (1). The blue LED means good air quality. The orange LED shows medium air quality, and the red LED shows poor air quality. If the device is switched on again, the display will light up in orange for the first three minutes. The display then changes to the air quality currently measured (blue, orange or red).
7. You can change the speed level by pressing the button for the selection of the speed level (8) (one LED for level 1, two LEDs for level 2, etc.). Increasing the speed level is useful when the air quality indicator (7) indicates decreasing air quality (blue for good air quality, orange for medium air quality and red for poor air quality). For optimal air purification, we recommend activating auto mode (9).
8. Pressing the button for auto mode (9) automatically adjusts the speed level to the current air quality (steps 1–4). If the air quality deteriorates, the device automatically selects a higher speed level. The display shows “Auto” when auto mode is activated.
9. By pressing the button for the timer (10) you can set the operating time for between one and seven hours (for example, 3 h = 1 h and 2 h LEDs lit, 7 h = 1 h, 2 h and 4 h LEDs lit). The selected time is displayed above the timer button with white LEDs. Press once to set the operating time to 1 h, press the button again for 2 h, and so on. The remaining time is indicated by the illuminated LEDs above the timer button. The unit switches off automatically after the set operating time has elapsed. If no LEDs are lit above the timer, the unit is set to continuous operation.
10. If you are bothered by the brightness of the LEDs and the air quality indicator (7) (in a bedroom, for example), you can switch these off by pressing the button for night mode (11) once. The controls cannot be switched off completely, but go out automatically after 10 seconds without input. Press the button for night mode again to return to normal mode.
11. Above the button for HEPA reset (12), four LEDs indicate the life span of the Dual FilterTM (2). If all four LEDs are flashing, the Dual FilterTM must be replaced. Reset the timer for the Dual Filter by pressing and holding the button for HEPA reset (12) (for about 3 seconds). If all 4 LEDs light up continuously, the timer has been successfully reset.
12. Press the WiFi button (13) to connect Roger/Roger big to the “Smart Life – Smart Living“ App von Tuya Inc. (available in the App Store and via Google Play) on your smartphone. The illuminated LED above the WiFi button indicates the connection between Roger/Roger big and your smartphone. You can control all the functions of the appliance via the app and monitor the air quality in real time, even when you are not at home. For more detailed information on how to connect your Roger/ Roger big to your smartphone, see the enclosed „WiFi – Quick Setup Guide“.

Cleaning and filter exchange

Prior to any maintenance, cleaning and after each use, switch off the appliance and unplug the mains cable (4) from the socket. To access the various filters, please refer to Point 1 of “Setting up / operation”.

Attention: Never submerge the appliance in water (danger of short- circuit).

• When cleaning the outside, rub the non-textile parts of your appliance with a damp cloth and then dry thoroughly.

• The textile pre-filter (1) must be cleaned regularly, once a month depending on the level of soiling, using the textile brush attachment for your vacuum cleaner. In the case of heavy soiling, the textile pre-filter (1) can also be washed in a washing machine. The antimicrobial protection provided by Sanitized® is guaranteed for at least 20 washes. Allergy sufferers are recommended to wash the textile pre-filter once a month and all other users every 3 months.

• The textile pre-filter will need to be removed from its plastic frame before it can be washed in a washing machine. In order to do that, all the material will need to be removed from the two positioning aids, the two pin, the
  4 tabs and the two corner tabs at the top. The textile pre-filter can be washed at 30° on a gentle cycle. Let the textile pre-filter (1) dry completely before attaching it to the appliance again. To do that, stretch the material over the plastic part so that the washing label is at the top and on the inside. All openings in the material to be threaded through are marked with bright-coloured thread. In addition, the material should be lifted over the two corner tabs at the top of the appliance. Caution: Never put the textile pre-filter, filter or other parts of the housing in the dishwasher!

• The Dual FilterTM (2) cannot be cleaned and must be replaced after 8–12 months. If all four LEDs flash above the button for HEPA reset (12), the filter must be replaced. Should you notice that bad odors are no longer being released, this is also an indication that the filter needs to be changed.

After replacing the filter, reset the timer for the Dual FilterTM by pressing and holding the button for HEPA reset (12) (for about 3 seconds). If all 4 LEDs light up continuously, the timer has been successfully reset.

Repairs

• Repairs to electrical appliances must only be carried out by a qualified electrical technician. If improper repairs are carried out, the warranty lapses and all liability is refused.
• Never operate the appliance if the adaptor or plug is damaged, after it has malfunctioned, if it has been dropped or has been damaged in any other way (cracks/breaks in the casing).
• Do not push any object into the appliance.
• If the appliance is beyond repair, make it unusable immediately by cutting through the cable and hand it in at the collection point provided for the purpose.

Disposal

The European directive 2012 / 19 / CE on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

Specifications Roger

Rated voltage: 100–240V / 50–60Hz
Rated power: 4–100W
Room size: up to 39 m2 with 5x/h air exchange (heavy air pollution and for allergy sufferers) up to 66m2 with 3x/h air exchange (moderate air pollution/normal use)
CADR: up to 465m3 /h (Clean Air Delivery Rate according to AHAM)
Dimensions: 420 x 516 x 200mm (width x height x depth)
Weight: 6.8 kg
Sound level: 28–65 dB(A)
Complies with EU
regulations CE / WEEE / RoHS / EAC

Specifications Roger little

Rated voltage: 100–240V / 50–60Hz
Rated power: 3–40W
Room size: up to 20m2 with 5x/h air exchange (heavy air pollution and for allergy sufferers) up to 33m2 with 3x/h air exchange (moderate air pollution/normal use)
CADR: up to 231m3 /h (Clean Air Delivery Rate according to AHAM)
Dimensions: 330 x 450 x 170mm (width x height x depth)
Weight: 4.7 kg
Sound level: 28–59 dB(A)
Complies with EU
regulations CE / WEEE / RoHS / EAC

Specifications Roger big

Rated voltage: 100–240V / 50–60Hz
Rated power: 4–90W
Room size: up to 62m2 with 5x/h air exchange (heavy air pollution and for allergy sufferers) up to 104m2 with 3x/h air exchange (moderate air pollution/normal use)
CADR: up to 736m3 /h (Clean Air Delivery Rate according to AHAM)
Dimensions: 420 x 520 x 340mm (width x height x depth)
Weight: 10.5 kg
Sound level: 28–58 dB(A)
Complies with EU
regulations: CE / WEEE / RoHS / EAC

This device contains a radio module from Stadler Form Aktiengesellschaft type: WBR3. It operates in the ISM band in the range 2.412 – 2.484GHz with a maximum power of 56.2mW and 89.1mW EIRP.

All rights for any technical modifications are reserved

Share your feedback about Roger/Roger little /Roger big on:
http://www.stadlerform.com/Reviews

For frequently asked questions go to:
http://www.stadlerform.com/Roger/support

Download instruction manual:
http://www.stadlerform.com/Roger/manual

Watch the video of Roger/Roger little/Roger big :
http://www.stadlerform.com/Roger/video

Stadler Form Aktiengesellschaft, Chamerstrasse 174, 6300 Zug, Switzerland Phone +41 41 720 48 48, Fax +41 41 720 48 44, www.stadlerform.com/contact

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>