SLV 1007653 Wall and Ceiling Light Instruction Manual
- June 1, 2024
- SLV
Table of Contents
SLV 1007653 Wall and Ceiling Light
Product Information
Specifications:
- IP Rating: IP65
- Max Dimensions: 5.5 cm x 5 cm x 20 mm
- Minimum Installation Depth: 9 mm
- Compatible Light Source: GU10, max 10W
Product Usage Instructions
Safety Guidelines:
Installation should be done by an approved electrician following local
regulations. Failure to do so may result in safety hazards. Operate the
product only with intact protection glass. If there is any suspicion of a
defect or malfunction, discontinue use and contact a professional.
Lamp Replacement:
Before replacing the lamp, disconnect the luminaire from the mains and
allow it to cool down. Use only compatible light sources as specified. Clean
the gasket when dirty to maintain proper functionality.
Care and Storage:
Clean external surfaces regularly with a slightly moistened cloth. Avoid
using harsh cleaning agents or pressure washers. Ensure that openings for
aeration or drainage remain unobstructed. Store the product in a dry and clean
environment.
Installation:
Switch off the mains power before installation. Only use recommended
accessories and suitable fastening materials for wall and ceiling surface
mounting. Follow local regulations for outdoor installations and do not seal
the product yourself. Install according to the declared IP rating and as shown
in the figure.
Electrical Connection:
Direct the fixed wiring with complete insulation at least 15 mm into the
housing. Ensure proper connection of live, neutral, and protective conductors.
Equip flexible wire ends with suitable wire ferrules for secure connections.
FAQ:
-
Q: Can I install the product myself?
A: The installation should be carried out by an approved electrician to ensure safety and adherence to regulations. -
Q: What type of light source can I use?
A: The product is compatible with GU10 light sources with a maximum power of 10W. -
Q: How should I clean the product?
A: Clean external surfaces regularly with a slightly moistened cloth. Do not use pressure washers or harsh cleaning agents.
The installation requires expert knowledge and may be carried out only by an
approved electrician under consideration of local and national regulations!
Technical Details are subject to change.
SLV UK
UK Unit E Chiltern Park
CA Bascombe Road, Bedfordshire
LU5 4LT
Read manual carefully and keep for further use!
- Safety advices for installation and operation.
- Disregard may lead to danger of life, burning or fire!
- Any works on the electrical connection only by electrician.
- Do not alter or modify the product.
- Do not fasten anything on the product.
- Do not cover the product.
- Operate only with intact protection glass.
- Take out of service when suspecting a defect or malfunction and contact your dealer or a qualified electrician.
- Take measures that children get not harmed by the product.
- Additional safety advices =
Use as directed
- Safety class I (1) – Connection with protective conductor.
- Operate only firmly fixed on an even surface.
- Operate only on normal or not inflammable surfaces.
- Do not strain mechanically or expose to strong dirt contamination.
- IP65: Protection against dust (dust-tight) – Protection against jetted water from all directions.
- Admissible ambient temperature(ta): -20°C …40°C.
Lamp replacement
- Disconnect luminaire from mains and let it cool down.
- Suitable light sources: GU10, 10W max.
- Clean gasket when dirty.
Care / Storage
- Disconnect product from mains and let it cool down.
- Clean external surfaces regularly with a slightly moistened (water) cloth. Do not clean with pressure washer.
- Openings providing aeration or drainage must be kept free.
- The following influences may have unwanted effects on the product: acidic surrounding, high salt content in the air, cleaning agents, fertilizer, thawing salt, chemicals.
- Store dry and clean.
Installation
- Switch off mains / fixed connection cable!
- Use only described accessories.
- Use only suitable fastening materials.
- Only suited for wall and ceiling surface mounting.
- Follow local regulations for outdoor installations.
- Do not seal the product yourself (e.g. with silicone).
- Install according to declared IP type.
- Install as shown in the figure.
Electrical connection
- Direct the fixed wiring with its complete insulation at least 15 mm into the housing.
- Equip flexible wire ends with suitable wire ferrules!
- Live conductor → Terminal L
- Neutral conductor → Terminal N
- Protective conductor → Earth terminal
Check secure fixation and proper function!
© 25.07.2023 SLV GmbH, Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany, Tel.
+49 (0)2451 4833-0. Made in China.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>