BLACK HORSE OFF ROAD 8DOSPA Spartan Rear Step Board Instruction Manual

BLACK HORSE OFF ROAD 8DOSPA Spartan Rear Step Board

Specifications

• Product: Rear Step
• Compatibility: 10-24 MERCEDES, 07-09 FREIGHTLINER, and 07-09 DODGE SPRINTER VAN (Excludes models with receiver hitch)
• Part Number: 8DOSPA

Maintenance

• To protect your investment, wax the product after installation.
• Regular waxing is recommended to add a protective layer over the finish.
• Do not use any type of polish or wax that may contain abrasives that could damage the finish.
• Use only mild soap to clean the Rear Step.

Inspections

• Perform periodic inspections to ensure that all hardware is secure and tight.
• Tighten any loose hardware as needed.

FAQ

• Q: Can this Rear Step be installed on models with a receiver hitch?
• A: No, this Rear Step is designed for models without a receiver hitch. Installing it on models with a receiver hitch may not be compatible.

REAR STEP

• 10-24 MERCEDES, 07-09 FREIGHTLINER AND 07-09 DODGE SPRINTER VAN
• EXCLUDES MODELS WITH RECEIVER HITCH

PARTS LIST

PROCEDURE

REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED. LET EXHAUST COOL COMPLETELY BEFORE INSTALLATION.

1. Start the installation under the driver side, rear of the vehicle, (Figure 1). Determine the correct installation for your model.
   Models without factory receiver hitch:

   • Locate the (4) factory holes in the end of the driver side frame channel, (Figure 1). Select the driver-side Frame Bracket, (Figure 2). IMPORTANT: On models without receiver hitch, install the Bracket on the inside of the frame channel, (Figure 1).

   • Attach the Frame Bracket to the inside of the frame with the included (3) 12mm x 110mm Hex Bolts, (6) 12mm Flat Washers and (3) 12mm Nylon Lock nuts. Do not fully tighten hardware, (Figure 2).
     Models with factory receiver hitch:

   • Locate the (4) factory hex bolts attaching the receiver hitch to the inside of the driver-side frame channel, (Figure 3). Select the passenger side Frame Bracket, (Figure 4). IMPORTANT: On models with a receiver hitch, the Brackets will be flipped side to side so the passenger side Bracket will be installed on the outside of the driver-side frame channel to clear the hitch, (Figure 4).

   • Hold the Bracket up in place on the outside of the frame channel to determine which (3) hex bolts to remove. Remove the necessary (3) hex bolts only.

   • Attach the Frame Bracket to the outside of the frame with the included longer (3) 12mm x 110mm Hex Bolts, (6) 12mm Flat Washers and (3) 12mm Nylon Lock nuts, (Figure 5). Do not fully tighten the hardware at this time.

2. Repeat the above Steps to install the passenger side Frame Bracket.

3. Carefully unwrap the Rear Step. Select the (2) 6mm Double Bolt Plates. Hold the Rear Step up to the (2) previously installed Brackets to determine the correct location for Bolt Plates. Slide the (2) Double Bolt Plates into the track in the bottom of the Rear Step, (Figure 6). Attach the Rear Step with Bolt Plates to the top of the (2) Brackets with (4) 6mm Flat Washers, (4) 6mm Lock Washers and (4) 6mm Hex Nuts, (Figure 7). Leave loose at this time.

4. Adjust the Rear Step as desired and tighten all hardware.

5. Do periodic inspections of the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.
Use only mild soap to clean the Rear Step.

Driver/left Side Installation Pictured

Documents / Resources

| BLACK HORSE OFF ROAD 8DOSPA Spartan Rear Step Board [pdf] Instruction Manual
8DOSPA Spartan Rear Step Board, 8DOSPA, Spartan Rear Step Board, Rear Step Board, Step Board, Board
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>