BLACK HORSE OFF ROAD 9B080205SS 3in Side Steps Stainless Steel Instruction Manual
- June 1, 2024
- BLACK HORSE OFF ROAD
Table of Contents
BLACK HORSE OFF ROAD 9B080205SS 3in Side Steps Stainless Steel
INSTALLATION INSTRUCTIONS
3INCH SIDEBARS
2022-2024 GRAND CHEROKEE (EXCL. 2022-24 4XE) PART# 9B080205A/ 9B080205SS
PARTS LIST:
| 1 | Driver/Left Sidebar | 1 | 10mm x 40mm Hex Bolt |
|---|---|---|---|
| 1 | Passenger/Right Sidebar | 3 | 10mm Lock Washers |
| 1 | Driver/Left Front Mounting Bracket | 3 | 10mm x 30mm OD x 2.5mm Flat Washers |
| 1 | Passenger/Right Front Mounting Bracket | 1 | 10mm x 27mm OD x 3mm Flat Washer |
| 1 | Driver/Left Center Mounting Bracket | 1 | 10mm Hex Nut |
| 1 | Passenger/Right Center Mounting Bracket | 1 | 10mm Threaded Insert |
| 1 | Driver/Left Rear Mounting Bracket | 1 | 10mm Insert Tool |
| 1 | Passenger/Right Rear Mounting Bracket | 12 | 8mm Combo Bolts |
| 3 | 12mm x 50mm Hex Bolts | 6 | 6mm Bolt Plates |
| 3 | 12mm Lock Washers | 6 | 6mm x 18mm OD x 1.6mm Flat Washers |
| 3 | 12mm x 32mm OD x 3mm Flat Washers | 6 | 6mm Lock Washers |
| 3 | 10mm x 50mm Hex Bolts | 6 | 6mm Hex Nuts |
*Notice: Center Bracket contains metal excess on top to identify between center and rear bracket PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY. USE ILLUSTRATION TO IDENTIFY BRACKETS AND SIDE BARS.
2. Starting on the Driver/Left front of the vehicle, remove the cover on the
bottom of the vehicle. Select the Driver/Left Front Mounting Bracket. Attach
the Mounting Bracket to the threaded insert in the front location with (1)
12mm Hex Bolt, (1) 12mm Lock Washer and (1) 12mm Flat Washer, (Figures 1 & 2).
Do not tighten hardware.
3. Attach the Mounting Bracket to the pinch trim with (1) 6mm Bolt Plate, (1)
6mm Flat Washer, (1) 6mm Lock Washer and (1) 6mm Hex Nut, (Figure 3). Do not
tighten hardware.
4. Move along the body panel to the center mounting location, (Figure 4).
Select the Drier/Left Center Mounting Bracket. Repeat Step 2 to install the
Bracket, (Figures 3 & 4). Do not tighten hardware.
5. Continue to the rear mounting location in front of the rear tire, (Figure
5). Select the Driver/Left Rear Mounting Bracket. Attach the Bracket to the
threaded insert with (1) 10mm Hex Bolt, (1) 10mm Lock Washer and (1) 10mm Flat
Washer, (Figures 5 & 6). Do not tighten hardware. Repeat Step 3 to attach the
Bracket to the pinch trim.
6. Unwrap the Driver/Left Sidebar. Place the Sidebar on top of the (3)
Mounting Brackets. Lift the Side Bar up and guide the studs down through the
Brackets. IMPORTANT: Do not slide the Side Bar on the Brackets, (front to back
or rotate), or the finish on the Side Bar may be damaged.
7. Attach the Side Bar to the Brackets with (6) 8mm Combo Bolts, (Figure 7).
Do not tighten hardware.
8. Level and adjust the Sidebar and tighten all hardware.
9. Move to the Passenger/Right side. Repeat Steps 2,3 & 5 to attach the
Passenger/Right Front and Rear Mounting Brackets.
10. Locate the center mounting location, (Figure 8). Select the
Passenger/Right Center Mounting Bracket. Hold the Bracket and line up to the
hole in the pinch trim to the lower slot in the top of the Bracket. Mark where
the top slot is located on the floor panel. Using a 1/2” drill bit, (not
included) to drill through only the bottom layer of the floor panel.
11. Select the 10mm Threaded Insert and the 10mm Insert Tool. Push the Tool
and Insert assembly into the factory hole. NOTE: If Insert fits too tight,
lightly tap it into place with a small hammer.
12. Firmly hold the handle on the Tool and tighten the hex bolt in the Insert
until it is fully collapsed and locked in place, (Figures 9 & 10). NOTE: Do
not over tighten the Insert or a pull out may occur. Once Insert is collapsed,
remove the tool from the Insert.
13. Attach the Passenger/Right Center Mounting Bracket to the Threaded insert
with (1) 10mm Hex Bolt,
(1) 10mm Lock Washer and (1) 10mm Flat Washer. Do not tighten hardware. Repeat
Step 3 to attach the Bracket to the pinch trim.
14. Repeat Step 6 to attach the Passenger/Right Sidebar. Do not tighten
hardware.
15. Level and adjust the Sidebar and tighten all hardware.
16. Do periodic inspections to the installation to make sure that all
hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Sidebars.
Driver Side Installation Pictured
Driver Side Installation Pictured
Passenger Side Installation Pictured
(9-A) Select Insert Tool and (1) Insert. Thread Insert onto end of Insert
Tool. Hand tighten only, do not tighten hex bolt
(9-B) Firmly hold assembly and push Insert into drilled hole.
(9-C) Hold Tool Assembly up tight in body panel. Turn hex bolt in Tool
clockwise to expand insert in body panel. Remove Tool once Insert is fully
tightened. Do not overtighten or Insert may be damaged.
Specifications:
-
Product: 3 Inch Sidebars
-
Compatible with: 2022-2024 Grand Cherokee (Excluding 2022-24 4XE)
-
Part Numbers: 9B080205A, 9B080205SS
-
-
FAQ:
Q: Can I use any type of polish or wax on the Sidebars?
A: It is recommended to avoid using any polish or wax that may contain abrasives to prevent damage to the finish. Mild soap is suitable for cleaning.
Q: How do I attach the Sidebar to the vehicle?
A: Follow the detailed installation instructions provided in the manual, ensuring proper alignment and secure tightening of all hardware for a successful installation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>