BLACK HORSE OFF ROAD 9JGCL21A 3in Side Steps Stainless Steel Installation Guide
- June 1, 2024
- BLACK HORSE OFF ROAD
Table of Contents
BLACK HORSE OFF ROAD 9JGCL21A 3in Side Steps Stainless Steel
Product Information
Specifications:
- Model: 3INCH SIDEBARS
- Compatibility : 2021-2024 Grand Cherokee L
- Part Number: 9JGCL21SS/9JGCL21A
PARTS LIST:
| 1 | Driver/Left Sidebar | 1 | 10mm x 40mm Hex Bolt |
|---|---|---|---|
| 1 | Passenger/Right Sidebar | 3 | 10mm Lock Washers |
| 1 | Driver/Left Front Mounting Bracket | 3 | 10mm x 30mm OD x 2.5mm Flat Washers |
| 1 | Passenger/Right Front Mounting Bracket | 1 | 10mm x 27mm OD x 3mm Flat Washer |
| 1 | Driver/Left Center Mounting Bracket | 1 | 10mm Hex Nut |
| 1 | Passenger/Right Center Mounting Bracket | 1 | 10mm Threaded Insert |
| 1 | Driver/Left Rear Mounting Bracket | 1 | 10mm Insert Tool |
| 1 | Passenger/Right Rear Mounting Bracket | 12 | 8mm Combo Bolts |
| 3 | 12mm x 50mm Hex Bolts | 6 | 6mm Bolt Plates |
| 3 | 12mm Lock Washers | 6 | 6mm x 18mm OD x 1.6mm Flat Washers |
| 3 | 12mm x 32mm OD x 3mm Flat Washers | 6 | 6mm Lock Washers |
| 3 | 10mm x 50mm Hex Bolts | 6 | 6mm Hex Nuts |
PROCEDURE
- REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. USE ILLUSTRATION TO IDENTIFY BRACKETS AND SIDE PRODUCT.
- Starting on the Driver/Left front of the vehicle, remove the cover on the bottom of the vehicle. Select the Driver/Left Front Mounting Bracket. Attach the Mounting Bracket to the threaded insert in the front location with (1) 12mm Hex Bolt, (1) 12mm Lock Washer and (1) 12mm Flat Washer, (Figures 1 & 2). Do not tighten the hardware.
- Attach the Mounting Bracket to the pinch trim with (1) 6mm Hex Bolt, (1) 6mm Flat Washer, (1) 6mm Lock Washer and (1) 6mm Hex Nut, (Figure 3). Do not tighten hardware.
- Move along the body panel to the center mounting location, (Figure 4). Select the Drier/Left Center Mounting Bracket. Repeat Step 2 to install the Bracket, (Figures 3 & 4). Do not tighten hardware.
- Continue to the rear mounting location in front of the rear tire, (Figure 5). Select the Driver/Left Rear Mounting Bracket. Attach the Bracket to the threaded insert with (1) 10mm Hex Bolt, (1) 10mm Lock Washer and (1) 10mm Flat Washer, (Figures 5 & 6). Do not tighten the hardware. Repeat Step 3 to attach the Bracket to the pinch trim.
- Unwrap the Driver/Left Sidebar. Place the Sidebar on top of the (3) Mounting Brackets. Lift the Running Board up and guide the studs down through the Brackets. IMPORTANT: Do not slide the Running Board on the Brackets, (front to back or rotate), or the finish on the Running Board may be damaged.
- Attach the Running Board to the Brackets with (6) 8mm Combo Bolts, (Figure 7). Do not tighten the hardware.
- Level and adjust the Sidebar and tighten all hardware.
- Move to the Passenger/Right side. Repeat Steps 2,3 & 5 to attach the Passenger/Right Front and Rear Mounting Brackets.
- Locate the center mounting location, (Figure 8). Select the Passenger/Right Center Mounting Bracket. Hold the Bracket and line up to the hole in the pinch trim to the lower slot in the top of the Bracket. Mark where the top slot is located on the floor panel.
- Using a 1/2” drill bit, (not included) to drill through only the bottom layer of the floor panel.
- Select the 10mm Threaded Insert and the 10mm Insert Tool. Push the Tool and Insert assembly into the factory hole. NOTE: If Insert fits too tight, lightly tap it into place with a small hammer.
- Firmly hold the handle on the Tool and tighten the hex bolt in the Insert until it is fully collapsed and locked in place, (Figures 9 & 10). NOTE: Do not over tighten the Insert or a pull out may occur. Once Insert is collapsed, remove the tool from the Insert.
- Attach the Passenger/Right Center Mounting Bracket to the Threaded insert with (1) 10mm Hex Bolt, (1) 10mm Lock Washer and (1) 10mm Flat Washer. Do not tighten hardware. Repeat Step 3 to attach the Bracket to the pinch trim.
- Repeat Step 6 to attach the Passenger/Right Sidebar. Do not tighten hardware.
- Level and adjust the Sidebar and tighten all hardware.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Sidebars.
Product Usage Instructions
Installation Steps:
Step 1: Parts Preparation
Ensure all parts listed in the manual are present before starting the
installation process.
Step 2: Mounting Bracket Installation
Follow the manual to install the Driver/Left and Passenger/Right Front,
Center, and Rear Mounting Brackets using the provided bolts, washers, and
nuts.
Step 3: Sidebar Attachment
Attach the Driver/Left and Passenger/Right Sidebars to the installed
mounting brackets according to the manual.
Step 4: Final Adjustments
Level and adjust the Sidebars as needed before tightening all hardware
securely. Perform periodic inspections to ensure all hardware remains tight
and secure.
**Driver Side Installation Pictured
**
**Passenger Side Installation Pictured
**
Cleaning and Maintenance:
Use mild soap for cleaning the Sidebars. Avoid using polish or wax
containing abrasives that could damage the finish.
Frequently Asked Questions
Q: How do I know if all the hardware is securely installed?
A: Periodic inspections should be conducted to check the tightness of all
hardware. If any part feels loose, tighten it immediately.
Q: Can I use any type of polish or wax on the Sidebars?
A: Avoid using polish or wax that may contain abrasives as it could damage
the finish. Mild soap is recommended for cleaning.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>